TL WR885N router how to set the speed limit inside the uplink and downlink 10

First fix the IP addresses of all machines, that is, in the DHCP service - statically assign addresses, specifically.

And then there's the per-IP setting:

The uplink is set to a maximum of 160, and the downlink is up to 2500 (the unit used in the router is kbps, which is the upload and ** network speed that they use in addition to 8, like Thunderbolt) is probably 20k upload per person, about 300k**.

Finally, remember to change the login password of the router, so that no one can change it back.

ps:You're 2 networks,Besides, your amount of machine is relatively large,Shrinking king TP is estimated to be a little enough,It's best to buy a dual-WAN behavior management router,JD to get a Huawei should be on the line (too expensive, Aitai, OK),You can ban Thunder,QQ or something,

First, test the total, upstream, and downlink bandwidth (online speed test tool), and then reasonably allocate the uplink and downlink traffic according to the number of clients.

Use your IP address, username, and password (prompted on the back of the router) and enter the address bar of your browser.

DHCP Service Client List View which clients need to be controlled, and record information such as host IP addresses.

IP Bandwidth Control Add a new entry (see message above).

Enter the IP address and uplink and downlink bandwidth (reasonably allocated according to the requirements) Enable Save.

Fill in the data reference:

The following parameters need to be set for IP bandwidth control:

Enable IP Bandwidth Control: If enabled, the bandwidth control rule will work.

Broadband line type: If the Internet access mode is ADSL broadband Internet access, please select "ADSL line", otherwise please select "Other line".

Total uplink bandwidth: The upload speed that can be provided through the WAN port.

The IP bandwidth control entry contains the following fields:

id: indicates the first rule.

Uplink bandwidth: If the maximum upload speed allowed through the WAN port and the minimum upload speed are guaranteed, the default value is used.

Enabled: The status of the rule, indicating whether the rule takes effect.

Configuration: You can perform and delete actions on rules.

References Routing Control Bandwidth.

Users can also limit the speed of each Internet device while they are on the router. Here's how:

1. Log in to the management interface of the router first, open the IP address of the router through the browser, enter the administrator account and password, and log in;

2. After logging in to the management interface, enter the MAC binding module and bind the allowed MAC (known Internet access devices);

3. Enter the bandwidth control page and limit the speed of the IP corresponding to the MAC address you want to limit the network speed.

Hello, method steps.

There are more users who access the router, and it is inevitable that they will encounter frequent movies, which occupies a lot of bandwidth, and limiting his bandwidth will not have any impact on his watching movies, and the router has this speed limiting function. Open a browser on a computer connected to the router, enter the IP: Enter, some router addresses IP:, a login box will pop up.

Enter administrator in the login box, the default is admin, the initial password is admin, it is best to change the initial password, log in to the router management background, different management interfaces of routers may be different, and the functions are similar.

In the left-side navigation bar, click IP Bandwidth Control to go to the bandwidth operation page.

The set bandwidth information is displayed on the page, and below the rate limit list, click the "Add New Entry" button.

In the new entry settings, enter the range of the IP address, if it is just a separate IP, just fill in the starting address, and then set the uplink broadband and downlink bandwidth, that is, the upload speed and ** speed, and click the save button.

Return to the IP bandwidth control page to see the IP record of the new limit you just set, and then put a checkmark before enabling IP bandwidth control, save and exit the router management background, and the rate limit will take effect.

It's also easy to delete the speed limit setting, just delete the entry of the setting.

Change a batch of relevant experience.

How to set the speed limit of the TP-Link router?

How to set the speed limit on the router.

How to set the speed limit on the router.

Router speed limit settings**.

How to set the router speed limit.