Two computers with 1M broadband router can only be used by one

1 Look at the manual of the router You can find some questions about the routing settings in the know, enter it in the IP address to set it.

It's admin password too.

Check whether DHCP is enabled for routing.

You try to change the network cable to the machine that can't be used, see if it's a problem with the computer, set your network connection to automatic IP, and let the router assign it, otherwise you may have the network but you can't get on.

2 You can make a local area network and connect another machine to your host computer in this way: change your own machine to other computers to log in to the web Open Share and set your own machine to.

Let's try it by setting it to (a value between 2 and 254 other than 1).

If you have a problem with the router settings, check whether the other one can get the address.

Ping outside the network is not working!

If you have changed three, it shouldn't be a router problem, look at the address set by the local connection of the machine!

Probably the router is not set up properly.

Buy another router and read the manual.

1. Check whether the line connecting to the other unit is smooth (exchange the connection to see if it is still not connected).

2. Whether the computer's network card or related software and protocols are enabled.

The person who asked the place where you bought the router to help you install it doesn't seem to cost money.

Hehe, there is no limit, generally depends on the DHCP setting of your router, if you set it to be 254 units.

If you set it to 100 units, but if your network bandwidth is not enough, it will get stuck if you connect more than 20 units, hehe.

The network cable is connected to the LAN port, and the mobile phone is connected to the wireless network

--Go back to the main ---

That's basically what it means.,I'm using my own desktop + ipod touch + dlink wireless router + ADSL,Network cable for desktop,Touch for wifi,Internet access is no problem。

However, you should note that if you use wireless routing, you must be a broadband access point, not a branch point in the LAN, and only wireless APs can be used in the LAN.

Theoretically, a home wireless router can connect to 253 computers, and the calculation method is: a total of 254 IPs in a network segment minus the 253 IPs occupied by the router itself, so theoretically 253 IPs can be allocated to computers. In practice, it will be slow to connect more than 20 computers to a regular wireless router.

Enterprise-level wireless routers (wireless APs) are divided into fat APs and thin APs, fat APs are not much different from home wireless routers, and thin APs require wireless controller AC+ wireless APs (thin APs). Theoretically, how many VLANs can be divided into APs, it can access about 253 * VLANs and computers.

A wireless router is a router with wireless coverage that is used by users to surf the Internet.

A wireless router can be seen as a device that sends broadband network signals from the wall of your home to nearby wireless network devices (laptops, WiFi-enabled mobile phones, and all devices with WiFi capabilities) through antennas.

Popular wireless routers on the market generally support four access modes: dedicated line XDSL cable, dynamic XDSL, and PPTP, and it also has some other network management functions, such as DHCP service, NAT firewall, MAC address filtering, dynamic domain name and so on.

Some wireless routers now have a signal range of 300 meters.

In the case of not affecting the network speed, it is generally possible to have 6 to 7 computers, otherwise the network speed is not good

It depends on how much bandwidth you have and how much bandwidth each unit requires.

The third floor is right, it is the conflict of IP addresses. You choose the computer that can access the Internet, run ipconfig all, you can see the IP address and DNS you are using, and directly enter your IP address bar according to the IP address, and set it to a fixed IP address. Especially the desktop one.

Then, when setting up on another computer, change the last item of the IP address to 2 or 3, as long as the two are different.

Add the local extension** and you're good to go.

In this case, if there is a conflict between IP addresses, the IP addresses should be filled in manually and should not be obtained automatically.

I've had this problem before.,It turns out that the computer with the problem is reinstalled on the system.。

Telecommunications? Netcom? There is a difference when it comes to setting.

It depends on the model of your wireless router, 340 is connected to 4 wired ports, and you can connect n if you are wireless

One, but the number of wireless connections will affect the speed and stability, 540 is more stable than the 340 model, or connected to 4 wired ports and n

wireless ports, which can be increased to 12 wired ports if you connect an external switch.

It depends on the model of your wireless router, which can generally be connected to 4 wired ports, and can be connected to n if it is wireless

If you want to connect a few more, you can only connect an external switch, which can be increased to 12 wired ports, and there are larger switches, more wired ports, but you have to take into account that you may be able to keep up with the network speed, I hope it can help you, thank you for adopting!

1.This is because your broadband account is limited by the number of Internet users set by the operator, only one computer is allowed to connect to the network by dial-up, if one computer is connected to another connection, it is error 691, if the account is set to the router, it can be solved.

2.The router is a device that sets up a LAN to achieve network sharing, and the general connection and setting methods are as follows: connect the network cable out of the broadband cat to the WAN port of the router, connect each computer to the LAN port of the router, and the IP address of the computer network card is set to be automatically obtained, enter it in the address bar of the computer browser, and specifically check the network parameters obtained by your computer network card, and log in through the IP address of the gateway) Log in to the router, and the general user name and password are admin, Select the WAN port settings, and set your broadband account and password to the PPPoE mode (if it is a fixed IP, you should select the static IP mode).