I have disabled the IP of my wireless router and can t access the Internet, what should I do?

You need to refer to the manual ---

1.The wire that comes out of the cat (ADSL dial-up device) is connected to the dedicated socket (inlet) of the router

2.Other devices are connected to the LAN port of the router.

3.Check the manual to find the router's default network segment settings and password.

For example, the CIDR block defaults

Account default: admin admin

segment) Carriage Return.

If you need a user and password, fill it out according to the manual.

5.Set the PPPoe dial-up column in the parameters, and fill in the dial-up account and password you applied for from Telecom.

6.Set up your router's DHCP and DNS

That's it.

- Pay attention to the areas you don't understand, and read the router manual more ---

Connect the computer with a network cable, enter the router, and set the ban back to a short time.

Enter the wired network, open the web page, enter, enter the router configuration, the IP address of the router and the NMS are not in the same network segment, you can set it as you like.

Restore the factory value and reset the settings.

Summary. 1. Reset the router. 2. It is recommended to use the method of connecting the computer to the router with a wired network to set up, after the computer is connected to the router, when the router is powered on, press and hold the black reset button behind the router (generally there is the word reset next to it) and do not let go, until the router indicator flashes, let go to reset the router.

3. After resetting, the router does not have any password, enter the setting address of the router in the address bar of the browser, and you can enter the router settings interface and reset the settings.

The router is set to prohibit Internet access, how to cancel it.

1. Reset the router. 2. It is recommended to use the method of connecting the computer to the router with a wired network to set up, after the computer is connected to the router, when the router is powered on, press and hold the black reset button behind the router (generally there is the word reset next to it) and do not let go, until the router indicator flashes, let go to reset the router. 3. After resetting, the router does not have any password, and the browser enters the setting address of the router in the address bar, and you can enter the router settings interface and reset it.

Use the following methods to cancel: 1. Enter the router: open the browser, enter the general router address in the address bar or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

2. Select IP Bandwidth Control --- leave IP Bandwidth Control unchecked. 3. Restart the router. 4. You can also upgrade the router:

Open the homepage of your own brand router - go to the customer service center - **center - **upgrade program. Enter in the address bar, enter the username and password are admin, enter the router settings webpage - click on the system tools on the left - restore the orange xiang return factory settings (at this time, be sure to prepare the Qi Zhi account and password for Netcom's dial-up login) - then click on the software upgrade (do not click on the upgrade after the upgrade page appears) - unzip the upgrade program just now and run the tftpd32 file - now you can click to upgrade. Select the network parameter options on the left - select the WAN port settings - select PPPoe for the connection type - enter the Internet access and password (given by Netcom) - connect (may have to connect several times) - save the settings - restart the computer, so that you will not be restricted from using only one computer with one IP.

WiFi "has been connected but unable to access the Internet" phenomenon around friends is very common, this article to tell you what is going on, let's first see if the problem may be in **?

External line problem: The router itself is interfered with by the neighbor's wifi channel.

1. Look at the indicator light to determine whether it is a problem with the external line or optical modem.

If you have a lot of wifi"Connected but unable to access the internet", the first time to look at the light of the modem, to see if the light of the light cat LOS light turned red, or red and green. If there is such a situation, it is likely to be due to the external line or the reason of the optical modem itself, just dial the corresponding operator** directly (China Telecom 10000, China Unicom 10010, China Mobile 10086) because you personally cannot solve this problem.

Second, in addition to the external line problem, it may appear in the router itself.

If dial-up routing is enabled on your modem, it may also be that the IP address of the modem and the IP address of the router conflict may cause Wi-Fi"Connected but unable to access the internet"。You need to change the IP settings of the router to an IP, generally the IP address of the router is, this is what you can try to change to this IP address.

3. Interference by the neighbor's WiFi channel.

Nowadays wifi will face a lot of interference, the biggest source of interference may be the neighbor's wifi, the same channel and adjacent channel wifi can cause strong interference to your home's wifi. In addition, Bluetooth also works in the unlicensed spectrum and can also interfere with your wifi. From the beginning, the router can basically solve this problem, or change the router.

1. In the case of wired LAN, the wireless router is restricted from accessing the switch by binding IP and MAC addresses. In the case of binding the IP and MAC addresses of the LAN computer, foreign computers and wireless routers that have not been added to the company's IP and MAC binding list cannot access the company's LAN.

2. Use network security management software to detect LAN wireless routers, and then prohibit the use of wireless routers. Such as network management software. This kind of software can detect the LAN wireless router, and after discovering the wireless router, it can directly block the network communication of the wireless router, so that all mobile phones, tablets, etc. that access the Internet through the wireless router cannot access the Internet.

3. Start the function of discovering the wireless router, mobile phone, tablet and portable wifi alarm on the network management system. Scan to LAN phones, tablets and wireless routers and pocket wifi to ban them. You can restrict P2P**, P2P**, ****, etc., control the broadband traffic of the LAN, and prohibit online shopping on the LAN.

Turn the router over, and there are instructions printed on the back, and the IP and physical MAC are changed from the local connection-attributes, and you can change it as you want. It's not difficult.

You've changed your computer's IP address to a router!

For example, the routing is.

You're ready to go!

Find a needle or something thin, press it in the reset hole of the router for more than 10 seconds, and the router will restore the factory settings, which should be fine. However, you will need to reconfigure the router to use it.

The IP address in the router is forbidden to surf the Internet, because the MAC filtering function is enabled, you can go to the router and disable the MAC address filtering function to lift the ban.

1. Enter the address bar of the browser, and the account password will default to admin (if you do not check the nameplate on the back of the router correctly).

2. In the router management interface - wireless settings - wireless MAC address filtering - turn off filtering.

Modify the IP address. If the Mac is also banned, modify the Mac, there is software on the Internet that specializes in modifying the Mac, and it is very convenient to modify it.

You can change the router to help in the router.

Workaround: Use **.

Name: 618ip**.

Language: Chinese Simplified.

Check whether the DHCP function of the route is enabled, and if you still can't get the IP, you can manually configure it on the IP segment of the route.

Use your IP address, username, and password (prompted on the back of the router) and enter the address bar of your browser.

IP Bandwidth Control Removes rules that are not needed.

Enable the DHCP server. Turn off MAC address filtering. You can all access the Internet.