What should I do if the ink can t get into the printer s continuous supply system?

<>1. The solution is shown in the figure above

2. Printer (English: printer), also known as printer, is a computer output device, which can permanently output the data stored in the computer to paper or transparencies in the form of text or graphics. The printer was invented by John Vaught and Dave Donald.

3. There are many types of printers, which are divided into percussion printers and non-percussion printers according to whether the printing elements hit the paper. According to the structure of the printed characters, it is divided into:

Full-glyph printers and dot matrix character printers. According to the way a line of words is formed on paper, it is divided into: string printer and line printer.

According to the technology used, it is divided into: cylindrical, spherical, inkjet, thermal, laser, electrostatic, magnetic, light-emitting diode and other printers.

4. The printer was invented by John Vaught and Dave Donald (who co-invented the printer). A device that prints the results of computer calculations or intermediate results on paper in numbers that can be recognized by humans, letters, symbols, and graphics in a prescribed format. Printers are developing in the direction of light, thin, short, small, low power consumption, high speed and intelligence.

5. There are three types of printers for home users, student users, SOHO, business users, etc.: laser printers, inkjet printers, and ink cartridge printers.

1.It turns out that after the ink runs out, there is no press to stop the recovery button, there is no press to restore 2Is your air supply hole open you don't take it off for a while, so that there will be air running into the hope can help you, other questions about the printer, you can ask me again.

The ink in the printer is not going away for the following reasons:

1. There is no seal for continuous supply, and there is air leakage;

2. The nozzle is blocked, resulting in the inability to produce ink;

3. The position of the continuous supply is too low, and it should be placed in the same horizontal position as the printer;

4. Replace the continuous supply with a new one for its own quality problems.

The continuous ink supply system is referred to as continuous supply, which is a new ink supply method that has only appeared in the field of inkjet printers in recent years. Continuous ink supply system, which uses an external ink bottle and then connects with the ink cartridge of the printer with a conduit, so that the ink bottle continuously supplies ink to the ink cartridge, as the so-called"Continuous supply"。

Hello pro Canon printer continuous supply display ink has run out is the solution 1, Canon inkjet all-in-one machine after a period of use, if the computer reports that the ink amount is low or the ink has been exhausted, it means that the ink cartridge ink is very small, and the ink cartridge needs to be added or replaced. 2. If the computer still prompts that the ink is used up or has been exhausted when printing after adding ink or installing continuous supply, you only need to reset the chip at this time, press and hold the stop reset button on the printer for about ten seconds, and then let go, at this time, the printer will resume normal printing. 3. However, the computer still shows that the ink amount is low and the ink lamp is flashing, which is a normal phenomenon.

The description is not cleared. 1. Open the round plastic cover. 2. Clean up the waste powder inside (very critical).

3. Add a bottle of fresh powder. 4. Pour in while shaking. 5. After adding new powder, reset the counter.

Remove the three screws and remove them whole. 6. Remove the entire clearing component. 7. Move the small plastic piece in the semicircle to the left, then go back to the compact, tighten the three screws, and the clearing operation is completed.

Extended Information: Other Canon Printer Faults**: Cartridge physical hardware failure.

Solution: Reinstall the cartridge, if the hopper flame barrier still exists, the cartridge may be defective, replace the cartridge with a new one: it is not a cartridge that can be recognized.

Solution: Install a cartridge that supports this model: The remaining amount of ink cannot be detected.

Solution: Replace the cartridge directly: The cartridge is installed in the wrong position.

Solution: Re-empty the cartridge to install it. If the fault persists, the cartridge may be defective and the chain will need to be replaced with a new cartridge.

There is air in it, it should be a bad seal, you can use the principle of air pressure to check it to see if you can do some treatment, it really can't only be after-sales.

You can take the ink supply tube off, fill the ink cartridge with ink with a syringe, and then connect the ink supply tube. It should be fine.

Even the air pressure is unbalanced, first of all, the two plugs should be turned on the constant pressure, and then solve the problem of filling the tube with ink, you can pull off the tube at the end of the tube to absorb ink, seal the big hole, and empty the air of the tube with the small hole, and then try to open the two holes at the same time, soak the tube in ink before opening, so as to solve the problem of stubborn reflux.

The hole in the cartridge is not sealed.

There's air in it. Try cleaning it.

Check the following questions, integrated ink cartridges with print heads, mostly rental Canon machines.

1. Check whether there is a lack of ink in the ink cartridge, resulting in too much air and not enough pressure, and use a syringe to gently prick the sponge in the ink cartridge to replenish enough ink.

2. Check whether the continuous supply pipeline is blocked, and separate the ink cartridges of the independent print head, most of which are epson machines.

1) A syringe can be inserted into the water outlet and the air can be drawn out until the pin ink is filled.

2) Check the sealing ring of the water outlet of the cartridge to see if it is poorly sealed.

3) Check whether the cheating pipeline, such as the continuous supply pipeline, is blocked.

4) Check the waste ink pump to see if it is working properly.