How to turn on the router function of the cat sent by Telecom?

<> put a network cable from router i to router ii, router i connects to lan port, router ii connects to wan port;

The management IP addresses of the two routers cannot be on the same network segment. If Router I is, then Router II is changed to;

If dial-up is set in router I, the modem should be set to bridge mode, and the WAN port of router i should be set to PPPoE dial-up. If dial-up is set in the modem, the modem should be set to the routing mode, the DHCP service should be enabled, and the WAN port of router I should be set to automatically obtain the IP.

Router I turns on the DHCP service, and the WAN port of Router II is set to automatically obtain IP addresses.

Router II turns on the DHCP service, turns on wireless and sets a password.

Restart Route II.

According to your description, 1First, connect the network cable on the modem side to the WAN interface on the router.

2.Connect the modem and the power cord of the router, turn on the switch (some brand devices will start automatically after connecting, no switch), and the hardware connection of the above router is complete.

3.Login router settings interface: Open a browser and enter the router login address in the address bar, the login address of different brands is different, but most of them are or check the label on the back of the router or the router manual).

4.Enter the login username and password, the default username and password please check the label or manual on the back of the router.

5.After entering the password correctly, it will enter the settings interface of the router, and the router that has not been set will automatically pop up the settings boot interface4After selecting the connection method, click Next, and the interface of entering the broadband username and password will appear, and the username and password filled in here is provided by the operator when handling the broadband.

6.After filling in the correct username and password, click Next, and the connection of the router is complete.

7.Turn on the wireless connection function, set the wireless connection name, and other options are usually default.

8.Set a password for the wireless connection.

9.Turn on the wireless network card on the computer to find the set wireless network name, click Connect, and enter the set password to connect normally.

I hope I can help you and get yours, Anhui Telecom has officially opened 4G service, please log in to the telecom online business hall for details, thank you for your attention and support to telecom products, I wish you a happy life!

What are the specific signals? I'll see if I can crack it.

You can connect the cat port to the router port by performing the following steps: Annihilation.

1.First of all: pay attention to the connection port, do not connect the connection port incorrectly. Generally, the connection port will be marked. Note: The network cable that comes out of the Telecom modem interface is connected to the WLAN port of the wireless router.

<>2.The other ports of the wireless router are connected to the computer with a network cable, and the wireless router has four outgoing interfaces, one of which can be connected to the computer.

3.After the network cable is connected to the computer, look at the back of the router, you can find the login and setting method of the route, is:, the default password is:admin, as shown in the figure below:

4.Enter and enter the password on the web page on your computer to open the router's settings screen. As shown in the figure below:

5.After the login is completed, we directly choose to get it automatically, as shown in the following figure:

6.If the automatic acquisition option is unsuccessful, you can go to the advanced settings. Check the WLAN setting status and set it according to the following figure

Note: The default gateway of this telecom fiber modem is:

7.Since the fiber optic modem does not need broadband and password, it can also be set up for static IP. As shown in the figure below:

How to set up wifi for telecom optical modem:

After the telecom optical modem is installed, connect the network cable port to one of the network ports of the optical modem (for example, network port 1).

2.Connect the other end of the network cable to the network port of the computer, check the network connection status, and ensure that the network is successfully connected.

3.Use the default address to enter the Fibre modem settings page, which is generally the default address, and the user name and password can be found behind the device.

Set up wireless basic information:

After logging in, click on the "Network" column, and by default on the left side, check "Enable Wireless", "Wireless QoS", and "Wireless Multicast" before the basic WLAN configuration.

Set a wireless network password:

In the navigation pane on the left, select WLAN Security Configuration and configure the following parameters:

Encrypt method: Mixed WPA2 WPA-PSK Click Save application.

After the setting is successful, you can connect with the network cable and connect to the Internet through the wireless network.

Open the IE browser, enter the address bar and press Enter, enter the router login interface, check the label on the back of the router, enter the login with reference to the username and password above, enter the Zhao wireless control after entering, select Open, don't forget to set the wireless password.

Connection Method:

1. How to connect the router and the cat. Find the port with the word "wan" on the back of the router and connect it with the cat with a network cable.

2. There are generally four "lan" interfaces on the back of the router, which are connected to the network cable interface of the computer.

3. After connecting, open the computer browser and enter " in the address bar to enter the wireless router settings page. Generally, this address is entered, and some need to be entered."

4. Before entering the settings page, you are required to enter your account and password, and the default system is generally "admin"."After entering, press enter to enter the router's settings page.

5. Find the network parameters in the left menu, click on the network parameters, and select "WAN port settings".

6. Then enter the Internet account and password provided by the broadband service provider as required in the WAN port settings, select automatic connection, and finally select "Save".

7. Then find the DHCP server on the left side of the router interface, select "DHCP Service", select "Enable" DHCP Service, and finally click Save, and the router settings are completed. You can see the status of surfing the Internet in the "Running Status".

8. The computer's settings are found in the lower right corner of the computer to find Start - Connect to - click All Connections.

9. Open the local connection, click on the properties, find the "Internet Protocol" in the general, double-click to open, select Automatically get the IP and DNS server address in the Internet Protocol properties, and finally click OK, you can go online.

Hello: You first connect the device as shown below.

Enter the address you see on the router in your browser, which is usually.

Then enter,Enter the corresponding account and password,Generally, the newly bought admin is indeed the operation interface,You will see a setup wizard on the left,Enter the setup wizard interface。

Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

Just like a normal router, just plug the cable in.

Connect the router to the cat's cable and set it up in the login.

IP settings router, connect OK

It depends on what kind of access method you have.

Buy a wireless router to connect to the back of the cat, set it up, and call ** to transfer manual services to telecommunications, and let him refresh the cat.

You're watching Internet TV. Don't have a set-top box. Telecom seems to be delivering.

After you connect the network cable to your modem, then pull out a cable from the modem to connect it to the router, and then pull the cable from the road to the set-top box and the computer to surf the Internet separately. If it's just device 1 and device 2, there's no way.

ITV's account and password are not the same as the account and password you use to surf the Internet,1:There is a cat in front,Connected to the wireless router behind,The account and password of broadband are automatically pulled out by the router,ITV and the computer can be directly connected to the LAN end of the router,But after a period of time,The TV may not have a picture,According to Telecom,ITV and broadband are to be opened separately and take two ** lines in。

2: Imagine that the network cable at the input and outlet end of the cat directly enters the switch, and then the switch comes out with two network cables, one into the wireless router to pull out the broadband account, and one into the ITV set-top box to pull the ITV account, so that they can not interfere with each other, and can be used.