I have already connected to the telecom wireless router, how can I add another router?

The router can not be the same as the IP address of the cat, you can set it according to the following method, in the case of not connecting the optical modem, set the LAN port setting of the wireless router, set the IP address to it, and then connect the optical modem, and then you can enter the wireless router, and then you can set other items on the router, enter the setup wizard interface, select PPPoe dial-up Internet access to fill in the Internet account and password, open broadband will have an account, fill in it. To learn more about service offers, click on the "****" customer service 217 below to answer for you.

For the second router setup, there are two ways to do it:

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

There are two types of cases: wired connection and wireless connection, and here is an introduction to wired connections

1.Wired configuration is simpler than wireless, and you only need to prepare a network cable. First of all, you need a router as the main router, this router is responsible for connecting to the Internet, and other routers are connected to it.

You need to enable the DHCP service in the router settings (if you don't know how to turn on and off the DHCP service, you can see the second method).

2.Connect the second router to the first router: Use a network cable to plug in any LAN port of the first router (the interface name is usually marked on the router), then plug in any LAN port of the second router and disable the DHCP service.

3.If you want to use multiple routers to connect, you can connect the nth router as described above. Note that all routers except the first router need to know how to turn off their DHCP function.

Turn the DHCP service on or off:

1.To turn off the DHCP service, first open your browser, type in the address bar with "this address" and press enter.

2.After entering this**, you need to enter the username and password of the router, the default username and password of the router can be seen on the back of the router.

3.Username and password on the back of the router.

4.After entering, Hu Meng found the DHCP service pants potato device option.

5.Here you can choose to enable or disable the DHCP service, and then click Save.

Telecom sent router to connect to a wireless router setup steps:

1. Connect a line from the LAN of Route 1 to the WAN of Route 2, and then connect Route 2 to the power supply.

Press and hold the energized route 2 with a small thin wire until the factory setting position is restored. (About 3-5 seconds, after flashing, you can use the computer to search for the wifi emitted by router 2 and connect it (generally passwordless).

3. Open IE browser, enter in the address bar, and press Enter. At this time, the system will prompt you to enter the username and password, and you can enter admin as the username and password, and you can enter the routing management interface.

4. Change the LAN address of route 2 from the original, and then restart route 2 After restarting, if the computer automatically obtains the IP, you don't need to change it, if it is manual, change the address of your local connection, change from the original to the gateway from the original to the LAN address of route 2 that you just redefined, you must change it, otherwise you won't be able to enter route 2.

5. Browser input, after entering, the system will automatically prompt the configuration setting wizard.

6. Find DHCP of route 2 and enable it instead (it is generally enabled by default).

7. On other computers, configure the computer IP according to the LAN parameters of route 2, and then you can access the Internet, such as the subnet gateway.

8. After connecting to the Internet with router 2, the shared printer configured on router 1 (you can also print the things in the router 2 computer directly.)

Dear telecom broadband users, then in the case of not connecting the optical modem, set the LAN port setting of the wireless router, set the IP address to it, and then connect the optical modem, and then you can enter the wireless router, and then you can set other items on the router, enter the setup wizard interface, select PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, open broadband will have an account, fill in it. Hope it helps you and have a great day!

Equipped with broadband, Internet room! Guangdong Telecom's online business hall is equipped with telecom broadband, faster, easier and more economical! 4M pure telecom broadband, no fixed line and mobile phone, one household and one line, no peak pressure on network speed, please click for details.

The broadband cat (wireless broadband cat) donated or purchased by China Telecom cannot directly use wifi wireless Internet access, and professionals need to enter the broadband cat (wireless broadband cat) configuration interface to set the routing mode before it can be used as a router (wireless router), and non-professionals cannot configure it by themselves. It is recommended that you purchase a wireless router to build a Wi-Fi environment. In this way, the wifi device can be used according to the prompt link.

The steps below are below to set up a wireless router.

Connect the network device correctly, connect the network cable (or direct home cable) of the cat to the WAN interface of the router, connect any interface of the LAN port of the router to the computer, open Internet Explorer on the computer, enter the correct IP address of the router (user name and password, the default user name and password are admin), you can also refer to the router instruction manual, enter the configuration interface of the router, and set the router correctly according to the setup wizard. Then, restart all your devices.

If you need to pay the phone bill and check the phone bill, please log in to the online business hall (

Enter the wireless router and set it in the WAN port.

The blue plug you are talking about is the fiber optic interface of telecommunications. In addition, it will be explained to you that the broadband cat (wireless broadband cat) given or purchased by China Telecom cannot directly use wifi wireless Internet access, and it is necessary to ask professionals to enter the broadband cat (wireless broadband modem) configuration interface to set the routing mode before it can be used as a router (wireless router), and non-professionals cannot configure it by themselves. It is recommended that you purchase a wireless router to build a Wi-Fi environment.

In this way, the wifi device can be used according to the prompt link.

The steps below are below to set up a wireless router.

Connect the network device correctly, connect the network cable (or direct home cable) of the cat to the WAN interface of the router, connect any interface of the LAN port of the router to the computer, open Internet Explorer on the computer, enter the correct IP address of the router (user name and password, the default user name and password are admin), you can also refer to the router instruction manual, enter the configuration interface of the router, and set the router correctly according to the setup wizard. Then, restart all your devices.

Telecom broadband home ** line or optical fiber connected to the corresponding cat, the cat out of the network cable connected to router A, router A set up normal Internet use.

The LAN port of router A separates a network cable to connect to router B, and there are two ways to connect it:

1: Connect to the WAN port of B, and the two routers are cascaded.

DHCP is enabled on Router A, dynamic IP address is set to Router B, and the LAN gateway of Router B is not on the same network segment as A to avoid IP conflicts. For example, if the gateway IP of A is A, then change the LAN port gateway of B to at least one of the first three digits that is different from that of A.

The wireless settings of the router are set according to the manual. After the settings are complete, the LAN port of Route A is connected to the WAN port of Route B.

2: The LAN port of A is connected to the LAN port of B, and the B router is used as a switch

When the computer is connected to the LAN port of Router B, as long as the DHCP function of the LAN port of Router B is disabled, the WAN port parameters do not need to be set. Do not have the same IP address as the A router to avoid IP conflicts. The wireless settings of the router are set according to the manual.

After the setting is complete, the LAN port of route A is connected to the LAN port of route B, and route B is equivalent to the expansion port of route A, which plays the role of a switch, and the computer can be connected to the LAN port of route B.

Dear Telecom users, Hello!

The key is that in the web settings of the second router, assign a static IP and a gateway to the WAN interface, the IP is in the same subnet as the computer connected to the first router, and the gateway is the internal interface address of the first router. In this way, a two-layer route is established. That is, the router from the landlord's side is not, then you first set the router to IP and turn off DHCP.

You set the IP yourself to ,,, set up the other machine from you, and the rest is the same as yours.

If you need to buy a phone and check the phone bill, please log in to the online business hall (, hundreds of mobile phones are low prices on the whole network, and now you can also enjoy a discount of 50 yuan for 2 yuan.

Yes, if there are two wireless routers, they can be connected by wired or wireless bridging, if the first one is not a wireless router, it can only be connected in the form of wired bridging.

The WAN port of the first router is set to PPPoE dial-up, and the second router is set to dynamically obtain IP

Also, don't set the LAN port IP to the same.

The situation you said can be realized, but there are a few things to pay attention to1 If you connect one or more routers behind a router, you may make enterprise users have such needs, and when broadband access is connected to an enterprise-level large router, the equipment costs thousands.

2 Use large routers Enterprise and routers and small routers Ordinary routers are combined to do network bridging, connect to the big router when accessing, and use small router when sub-networking.

After the 3 major routers are successfully connected, you need to set up the routers you want to bridge on the router login page.