How to install a floor drain in the bathroom? What are the steps?

When installing the floor drain, clean up the periphery, block the drain pipe mouth, apply cement putty around the floor drain, take out the anti-odor core, the floor drain panel and the tile need to be aligned and installed, and the surrounding area is coated with glass glue, and then install the anti-odor core after drying. When installing the floor drain, it is necessary to pay attention to the height difference between the cover plate and the floor tile, as well as whether the pipeline installation is qualified.

According to the size of the floor drain selected by the pipeline, the installation position should be connected with the sewer in advance. First make it flat and then install it, then do a good job of waterproof treatment to avoid water leakage, and finally test the effect.

The first point is to install in the bathroom, it is best to choose a good odor-proof one with moisture resistance, so that the floor drain can be installed very perfectly, and there will be no smell. The second step is to clean up the perimeter of the hole, apply putty glue, and then install the drip leak, which can be dried for about two hours, and the cover must be covered very tightly, so that the installation is particularly good.

Preamble: When installing floor drains in the bathroom at home, the location of the installation must be selected close to the corner of the wall, and the position of about 10 cm is the best. When installing floor drains in the bathroom, most of them are designed by water and electricity installers.

Some of the floor drain holes have been left, and since they have been installed when building the house, they only need to be installed directly next to the sewer pipe. However, if you feel that the location of the designed floor drain installation is not particularly satisfactory, you can also choose to connect the water pipe separately and reinstall the floor drain. <>

In the decoration process, if you want to install the floor drain in the bathroom in a reasonable position, you must consider which side of the shower is facing in the shower, and which side should leave a floor drain position under it. Because the water flow is very large when taking a bath, in order to better drain the water, it is best to install 2 or 3 floor drains in the bathroom. In this way, an effective drainage system can be achieved, and even due to the long-term occupancy of the house, the floor drain will be blocked.

If one floor drain is blocked, and there is another floor drain in the bathroom, the effect of drainage can also be achieved. <>

When choosing the location of the floor drain, most people consider that the installation is not in the way, and the floor drain itself is parallel to the ground. No matter what position it is installed in, it will not feel in the way, but when installing, it should be taken into account that there are more drainage places, so it should be installed. At the same time, it is necessary to consider the height of the bathroom, and the installation of floor drains needs to find a professional tile master for lamination.

Otherwise, it is easy to cause uneven floor drainage, and the drainage system cannot achieve the effect of drainage. <>

The installation records are handed over to the tiling master, if the tiling master in the process of tiling, can make the floor drain reasonable to achieve the effect of drainage, which requires a certain amount of experience. In life, I think that installing floor drains is a very simple thing, but I don't know that because there are floor tiles on all sides, once the floor drains are flattened, the water flow is very small, and the drainage function cannot be achieved.

It is best to install it around the toilet, because if there is stagnant water at this time, it can quickly flow under the drain, and if you are taking a bath, you can also quickly let the water evaporate.

Install two, one in the shower room or bathroom, and the other outside the shower room and inside the bathroom. In the floor drain of the bathroom, you need to make a small slope so that the water can flow smoothly to the floor drain of the bathroom and facilitate the discharge of wastewater. The outside floor drain can be placed under the sink or on a lower ground next to the toilet.

The floor drain is best installed at the lowest point in the bathroom, below the surrounding floor. At the same time, pay attention to install floor drains at the lowest point between the shower rooms.

When installing the floor drain, it must be separated from dry and wet, and it should also be installed in the corner, so that it will not affect the appearance.

1. Clean up. First clean up the stains and mud around the original floor drain, and then use clean water to wet the inner wall of the lower oak water pipe, which must be completely wet in order to ensure that the circumstantial evidence is installed.

2. Installation. Place the floor drain in the hole, and then press the floor drain into it vigorously, and ensure that the level of the floor drain is lower than the ground, so as to ensure that the water can flow smoothly into it.

3. Sealing. After the installation of the slow fiber, the place where the floor drain is connected to the water pipe is sealed with sealant to ensure that it will not leak from the gap to the downstairs toilet when draining, which will cause disputes.

As one of the most important drainage system components in a modern family home, floor drain plays a considerable role in the installation of the bathroom, drainage, deodorization, anti-clogging, etc., and it can even be said that the installation of floor drain is the most important step in bathroom decoration.

Once there is a problem with the installation of the bathroom floor drain, the future home life will be greatly affected, how to install the bathroom floor drain so that you can see the drainage and quickly? Next, Xiaowei will take you to compare the installation method of the bathroom floor drain!

1.Diagonal cutting and paving.

This kind of label is very common, cutting tiles along the outer corner of the floor drain to form a semi-diagonal, and it also needs to be tilted to the corner of the wall when laying so that the floor drain position sinks and allows for easy drainage.

2.Cross-shaped paving.

This is also a very common way to align the four corners of the floor drain with the crosshairs of the tiles, which is still very beautiful overall, but has a big drawback, that is, it is inconvenient to make slopes, so the water will not be fast.

3.Semi-diagonal paving.

This method is suitable for sewers close to the wall, the tiles are cut into three pieces, and the floor drain is installed against the wall, and when paving with this method, it is also necessary to pay attention to the sloping corners so that the floor drain is at the sinking point and drains particularly quickly.

4.Four-sided cutting method.

This method is also a very common practice, cut a tile into 5 pieces, regardless of the location of the floor drain, take the floor drain as the center, make a box on the floor drain, and make a diagonal line from the center, make a ramp when tiling, although this method is not very good, but it is definitely the most practical method.

5.Paving in a misaligned way.

If the tiles are a misplaced paving solution, the floor drain can be installed this way and the floor drain can be placed at the intersection of the four tiles, however this paving method is more suitable for use on balconies and is not recommended for large amounts of water in the bathroom.

6.Edge interrupt mode.

If the floor drain is located on the side of the wall and the floor tiles near the wall are straight, you can cut the tiles and leave the floor drain directly at the ends, which is simple and convenient, and is perfect for families with recessed shower rooms!

One thing to keep in mind when installing a floor drain is that you have to make a ramp! It is necessary to pay attention to reserve a certain slope in advance, if the slope is too large, it is easy to affect the installation of sanitary ware such as toilets, if the slope is too small, it may not work normally, if the slope is reversed, the consequences will be more serious and will be directly displayed, the phenomenon of water pouring out of the door.