Is it normal for the car to have bubbles just on the film, and it will disappear in a few days

Some bubbles are not clean enough in the glass, there are dust particles in it, some are moisture inside, just dry it for two days, if it is not eliminated after two days, you can use an embroidery needle to prick a small hole in the bubble to drive away the air, if you feel too many bubbles to go to them to re-paste.

Abnormal, the air between the glass and the film is not squeezed with a scraper to the direction of the post, this bubble will not disappear after a few days, it will only change with the temperature of the temperature, the temperature is higher when the temperature is higher, the temperature is lower when the temperature is smaller, you can try to use a needle to break the bubble, discharge the gas and compact the vacancy, if it is due to the bubble position is not clean, after the gas is discharged, it will still not be tight. In this case, you can ask for re-pasting, needles and other operations are limited to their own film before use, and it is recommended to re-paste it if the store sticks it.

Hello car owner! It's not normal, there are dust spots in it, I hope it can help you.

Hello, yes, you can run for three or two days and then see, if there is any, and then consider the quality of the film, I hope mine will satisfy you, I wish you a happy car.

Hello, car owner, this is not normal, this is not posted well, thank you for your support to the car master, thank you.

Hello, the film is not pasted well, there is still air in it, you may have to re-apply the film, I hope it can help you.

What should I do if there are a lot of bubbles after the window glass is filmed? Teach you a few tricks.

Most of the small bubbles disappear when sunburned. Car wrapsAfter there are bubbles that will disappear automatically.

Inferior car film will have a foggy feeling when viewed from the inside out. If the film layer is coarse, bubbles and wavy lines will appear.

Safety hazards: the most common is that the film master technology is not in place, the glass surface is not cleaned in place, there is dust adherence, with the film after the strength of the paste rises, the pressure around the sand or dust appears, the phenomenon of blistering occurs, and degumming may also cause bubbles.

It will not disappear automatically, and the air bubbles need to be cut and discharged manually. Air bubbles in the car film are caused by the fact that there is air between the car film and the glass that is not discharged. The film bubbles are completely sealed between the window and the film, and there is no place to leak, so the bubbles will always exist and will not disappear for a short time.

There are two reasons for the bubbles in the car film, one is the quality of the car film itself, and the other is the construction quality of the car film. For the first reason, the majority of car owners should determine whether the film product is a brand car film and whether the film is genuine before the car film. If the quality of the film is not up to par and there is no warranty card guarantee for the product, then blistering, degumming, and fading are inevitable.

It is recommended that car owners should not be greedy for cheap when carrying out car films, and choose brand car films, only in this way can the quality of car films be guaranteed, so as to reduce the possibility of failure after car films.

If the blistering is formed by the incoming air, it has little effect, because the incoming air does not have much effect on the adhesion of the membrane, so you only need to find a sharp object like an embroidery needle to puncture the bubbles, and then use a flat plate to scrape the bubbles out. If it is caused by impurities such as dust and sand, you need to go to a professional place to deal with it.

If it is a small blister, perhaps a blister, it will usually disappear after 1 week. Otherwise, it's a bubble that can't disappear on its own. It's a hands-on approach.

Find an embroidery needle, gently prick the bubbles, and then slowly squeeze it with your hands to squeeze the air out inside.

Air bubbles in the car film are caused by the lack of air between the car film and the car glass.

Because the film bubbles are completely sealed between the window and the film, there is no place to leak, so the bubbles will always exist and cannot disappear for a short time. Unless the bubble is actively cut, it is manually discharged.

The small bubbles that have just been pasted can disappear automatically after drying, and can be dried in the sun again, and if they have not disappeared after a week, find a film shop to deal with it.

Car wrap is now very common, and wrapping for cars has also become a necessary choice for car owners after buying a car. But we can often see such a phenomenon, many cars will have a lot of bubbles on the rear window and side window glass soon after the car film, which greatly affects the aesthetics of the vehicle, what is going on? What should I do if this happens?

To figure this out, we first have to look at the causes of these bubbles.

There are actually three reasons for the appearance of bubbles.

The quality of the car film is not good, and the quality of the car film on the market is uneven. A lot of low-quality, poor-quality car films are said to be imported from abroad, in fact, the cost of these car films is low-cost, and the glue used is not good, many car owners buy it in order to save money, and bubbles will appear after a period of time.

Many people will find a master they can trust when repairing and maintaining their cars, after all, the film is related to the technical level and the tools used. In many places, you will have an apprentice apply the film to you, and improper craftsmanship or incomplete cleaning will cause bubbles to form.

After the car film was just pasted, the owner did not pay attention to the precautions of the car film, and did not maintain the car film in time, so that the bonding state of the car film and the window glass was not stable, which led to the existence of local blistering.

How to deal with blistering.

1.If the bubble is relatively small, you can use a utility knife to cut a small hole in the bubble, and scrape it flat with a paper hard card.

2.Puncture with a fine needle and then smooth with a cotton cloth, this can also only be used for relatively small bubbles.

3.If the bubble is closer to the edge of the glass, you can scrape it directly with the card, and the bubble will disappear after a few more scratches.

4.If the bubbles are caused by near air, you can tear off half of them and re-apply them according to the normal film process, which is not recommended to be done by yourself.

5.If the bubbles are not cleaned because of dust, etc., you need to find a professional to deal with them.

6.The car film of the regular car film shop has a warranty card, and once the car film appears blistered, it is necessary to go to the store to reload.

The blistering phenomenon of car film is mainly due to two aspects, one is that there is a problem with the quality of the car film, and the car film bought by the car owner is an inferior car film, or a fake film. There are too many types of car film, and the height is uneven, some consumers think that the car film is not worth selling and buying at a high price, so they bought a cheap film, but they don't know that the quality of the cheap film is very poor, not only does it not have the protective effect that the car film should have, but even the toxic gas is released at all times, plus the workmanship is rough, the material is cheap, and the sun is exposed, it is easy to appear bubbles, deformation and hemming, which affects the appearance, blurs the vision, and endangers health and driving safety.

Another aspect is that the construction is not professional enough, resulting in bubbles. In order to achieve the desired effect, it is best to carry out the car film in a dust-free workshop to avoid the dust in the air sticking to the gaps in the car film and causing bubbles; Or the glass is not cleaned when the film is attached, and it is easy to produce bubbles after pasting. It is recommended to go to a regular beauty shop and ask professional fingers and construction personnel to operate.

If your membrane has bubbles, if the foaming is small and not much, gently puncture it with the tip of a needle, then wrap the towel with a thin card and slowly scrape it flat; If the area is large and affects the line of sight, it is better to go to the physical store and let the professionals solve it.

However, no matter how many bubbles there are, you need to go to a professional film shop to inquire about the cause of the bubbles, which will not affect driving safety. If it is an inferior film, for the sake of health and safety, it is necessary to re-paste a new film. If you paste it again, you must choose a high-quality film, consult and experience more, and feel the effect before making a decision.

There are air bubbles behind the film that can't go down on their own.

There are generally two reasons for the appearance of bubbles: inferior car film, which will feel foggy when viewed from the inside out. If the film layer is coarse, bubbles and wavy lines will appear.

Another reason is the most common, that is, the film master technology is not in place, the glass surface is not cleaned in place, there is dust adherence, as the adhesive strength of the film rises, the pressure around the sand or dust appears, the phenomenon of blistering occurs, and degumming may also cause bubbles.

The car glass film has bubbles and is introduced as follows:

If there are many bubbles, a large area, or caused by impurities such as dust particles, it is generally difficult to deal with it yourself, it is recommended to go to a professional beauty shop for treatment, and if necessary, you can consider replacing it with a new one. Don't be greedy for a small bargain when applying a film to your car, choose to buy a high-quality car film or go to a regular and professional car beauty shop for a film.

Only in this way can the film be guaranteed, so as to reduce a series of unnecessary troubles after the car film. If the blistering is caused by air ingress, it has little effect because the air does not have much effect on the adhesion of the membrane.

Causes of bubbles:

The quality of the car film is not up to par.

Some experts said that although the car film industry is not big, but the water is very deep, a small number of repair shops will be shoddy, to the inferior car film labeled with a brand-name logo, fooling consumers, some of the poor texture of the car film, after the exposure to the sun, a chemical reaction occurred, blistering can not be avoided.

2.There is a problem with the mounting process.

When a small number of repair shops are busy, they may ask some apprentices to put the car film on you, which may cause bubbles to occur because the process is not necessarily in place; If the construction site is not properly cleaned, sand and dust will adhere to the surface of the car body, which may also lead to the formation of air bubbles.

Expand content: car film: there are many car film brands on the market, ** is also far away, many car owners often look left and right to make up their minds, in fact, a good car film is also a high-tech product, choose a lot of car film knowledge. The film has high requirements for technology, soft and hard conditions, such as dust-free environment, special equipment, standardized operation procedures and skilled technology.

However, due to the extremely low threshold for joining the ranks, some illegal traders are mixed in, counterfeit and shoddy products are rampant, and consumers often suffer losses due to ignorance.

Precautions: Many car owners already know that the film has to go to the regular car decoration store, but most car owners may not know that when it is cloudy, the air humidity is large, and the suspended matter in the air is also significantly reduced, which can avoid the appearance of impurities between the film and the glass, which is the best time to apply the film.

The cleaning of the glass is the basic work of the installation and pasting. Generally, there are three steps in cleaning glass: glass flaw detection, removing rubber particles and gravel; Glass dust removal and cleaning (due to the need for water dust removal and lubrication, pay attention to prevent water leakage into the car's audio and electronic control system, and must be cleaned three times); Cleaning before filming.

When washing the rear windshield, be sure to protect the heating wire.

When the store is required to paste the front and rear windshields, it is best not to open the knife and post it neatly, otherwise it will lose its explosion-proof property and affect the appearance.

If the bubbles are not very large and the volume is relatively large, you can cut a small incision and then slowly scrape it with a scraper and a baking gun. If there are not many bubbles and the volume is small, we can prick the bubbles with a needle and flatten them. If you encounter sand particles in the car film, you can only turn to a professional 4S shop or car beauty shop.

There is little possibility.

Because of the bubbles that have appeared.

It doesn't go away because of time.

It's common sense.

It is not that the car has air bubbles just after the film, and there will be it after two days of drying.

If the bubbles are caused by impurities or dust, or there are too many bubbles, it is more troublesome, and it is necessary to bring a warranty card professional to deal with it. Car owners must not continue to use it because they are reluctant to spend money, and it is best to replace it with a new one. This is because the blistering solar film can also have an impact on the health of the driver and the occupants.

Many car owners believe that the reason for the blistering of the window film is mainly because the quality of the sun film is not up to par. Indeed, when the quality of the solar film is not up to par, it will be exposed to direct sunlight, and the temperature on the window glass will be quite high, and it will blister after a long time. There are also two possible causes of blistering of the solar film.

Not normal, of course. The car film should be smooth and free of air bubbles, if there are air bubbles, it means that it is not well pasted.

It must be abnormal, there is a dirty thing on the surface when there are bubbles to indicate that the sticker is not cleaned, you can take a needle to puncture the bubbles and expel the air.

It is not normal for air bubbles to appear after the car film, and generally speaking, the car body after the film is relatively flat.

What should I do if there are a lot of bubbles after the window glass is filmed? Teach you a few tricks.

If there are occasional small bubbles, you can leave them alone. Under normal circumstances, whether it is summer or winter, the adhesive of the film is at most in a week, and it is all dry. Some of the bubbles will disappear on their own.

If there are still bubbles after a week, you can press it with your own hands to observe. Often some air bubbles disappear when pressed, if it is useless to press, you can find a needle to gently puncture the bubbles, and then press to exhaust it.

Hello. The car has just finished applying the film, and there will be no bubbles.

Generally, it is filmed, and the experience is not enough.

So it causes bubbles in the film.

In this case, you should negotiate with the merchant as soon as possible.

Let them find an experienced master to re-paste it for you.