When it starts, it prompts an error Please help the master Thank you 20

The memory module is loose, plug it in tightly!

This is the motherboard BIOS setting interface, if you automatically enter this interface when you boot up, it may be caused by the following situations.

First, the Delete key, F2 key, or decimal key of the numpad may be pressed by something, or the computer thinks that these keys are pressed, and pressing these keys during the boot process will enter the BIOS settings interface.

Second, if the computer does not have a hard disk installed, or a hard disk is installed but the system is not installed, or a hard disk is also installed but the hard disk or the system is damaged and the system cannot boot the system, it will also automatically enter the BIOS settings interface.

It is recommended to check if the keyboard is pressed by something, if the keyboard is not pressed, then consider the hard disk failure, it is recommended to find a local computer city or computer store to repair it.

Once you're in the motherboard BIOS, you press F10 to save and exit it.

Your computer has entered the BIOS setting mode, which is generally caused by the loss of BIOS settings caused by the computer motherboard battery being out of power, you can replace the motherboard battery and then reset the BIOS settings and save them, which should be solved.

Did you reinstall the system yourself? Look at the BIOS settings.

Turn on the computer and press F8 to see if there is a hard disk.

You must be booting or pressing the static disk to restart.

1. Force restart the computer, hold down the F8 key before entering the system, and select the last correct configuration to try.

2. If the software or driver is installed before the blue screen, enter the safe mode, uninstall or delete the newly installed software and driver, and then boot the computer to try again.

3. If there is still a blue screen after deletion, or you can't enter the safe mode at all, then reinstall the operating system and try it.

4. If the blue screen is still blue after reinstalling the system, the hardware problem will be considered. First of all, clean the dust inside the computer thoroughly, remove the equipment on the memory, graphics card, and PCI slot, and test it with an eraser. Because the temperature caused by dust is too high, poor contact, etc., it will also cause a blue screen; At the same time, remove the CPU, graphics card and other fans and replace them with new heat dissipation silicone; Also, check that the temperature of all hardware is normal.

5. If it still doesn't work after cleaning the computer, then use the replacement method to check the computer hardware, if there is no replaceable hardware or not familiar with the computer, it is recommended to find a professional maintenance personnel to deal with it.

6. Hardware replacement is troubled in the following order: memory, hard disk, graphics card, motherboard, power supply, other hardware, and CPU.

Let's take a look at the most common 0x0000000a of blue screen errors. This error is usually caused by an error in a hardware driver in the Windows system or the driver is incompatible with the system.

If you encounter this kind of error 0x0000000a, it is recommended to restart the computer and press the F8 key to enter the advanced options menu of Windows, and select "Last correct configuration" to enter the system.

After entering the system, it is necessary to check whether there is a driver of some hardware updated recently, or what new hardware is installed, if it is a driver of updated hardware, then we recommend using the driver wizard to reinstall the driver.

If you have installed new hardware, then it is recommended to remove the new hardware first, try to restart the computer, and see if the blue screen appears, if the normal system boots normally, it proves that the new hardware or the driver of this hardware has a problem.

It's a blue screen, and it's time to install the system. There are 3 main reasons.

1 If there is a problem with the hard disk, it is directly judged that the sound of the hard disk is loud, indicating that the hard disk is a problem.

2 Loss of system files leads to a blue screen at boot.

3 The memory module is broken.

In general, there is a high probability of system problems. Reinstall the system and take a look.

Your computer has now crashed and can only be solved by reinstalling the system.

There are two ways to reinstall a system.

Reinstalling the system will only change the system in the C drive of the computer, such as the files and things in the D and E and F disks of the computer.

The first is the optical disc mounting system. It is suitable for those who have a good understanding of the BIOS settings of the computer. [Find and enter the option containing the word "BIOS" in the BIOS interface, 1.]“advanced bios features”

2.After going to "Advanced BIOS Features", find the first boot device option with "first", "First boot device".

3."First Boot Device" option, select "CDROM" Enter, after the configuration is set, press the "F10" key on the keyboard to save and exit, then the computer will restart by itself, and the rest is to install the system automatically.

The instructions above are the steps to set up the BIOS boot. Each computer has different BIOS settings, you can refer to it. Once you've learned it, you'll be able to pack the system on disc. 】】

The second is the USB flash drive mounting system. U disk system, you need to make the U disk into a boot disk first, and then from the online ** system, and after decompression, copy the system with GHO to the boot disk that has been done quietly.

1.The installation system can go to the win7 ultimate base.

2.After watching the tutorial on how to make a USB flash drive, you will use the tray system. Go to the computer store.

Learn how to install the system.

It is suitable for those who have a good understanding of the BIOS settings of the computer. [Find and enter the option containing the word "BIOS" in the BIOS interface, 1.]“advanced bios features”

3.After going to "Advanced BIOS Features", find the first boot device option with "first", "First boot device".

4."First Boot Device" option, select "U disk" to enter, after the configuration is set, press the "F10" key on the keyboard to save and exit, then the computer will restart by itself, and the rest is to install the system automatically.

Above are the steps to set up the BIOS boot. Each computer has different BIOS settings, you can refer to it. Once you have learned it, you will be able to use the USB flash drive system.

1. Repair the system: If you can't enter the system normally frequently, press F8 immediately after booting to see if you can enter the safe mode or configure the correct mode for the last time, if so, the system will automatically repair the registry after entering, and recall what operations were done when the first few abnormal phenomena occurred, and according to the suspicion that a certain application software (or driver) caused the problem, uninstall it, and then exit normally, and then restart it should be able to enter normal mode. If you have security software installed, you can use 360 Security Guard plus 360 Antivirus or Kingsoft Antivirus and other similar security software in safe mode to clean up your computer, optimize and accelerate (remove redundant boot auto-start programs, defragment hard disks, etc.) and check and kill Trojans and viruses.

2. Reinstall the system: If the above operations are invalid, you need to reinstall the system (Note: If the C drive has important data, it needs to be backed up in advance).

There are many ways to install the computer system, in addition to the time-consuming and troublesome complete installation method that is rarely applied now, the commonly used is clone installation, and the method is divided into: hard disk installation, U disk installation and optical disc installation, etc.

U disk start the computer copy C: Windows System32 Config Regback system to C: Windows System32 Config to overwrite the original file, restart!

Press the chassis panel reset key, keep pressing F8, enter safe mode, and tap Start-Restart.

System files are corrupted! Take it to a computer repair shop and install the system!

Factory reset the motherboard BIOS and set it up again. The boot sequence 123 needs to be set.