How to make distilled water fast and abundantly, want to make some distilled water at home, how to g

Preparation: a small bowl, pot, water, ice cubes.

3. Heat the water in the pot below, as shown in the figure below.

4. Next, put the lid of the pot on the pot backwards and put a few ice cubes on the lid.

5. Finally, take out the small bowl and get distilled water, as shown in the figure below.

Fill the kettle with water and boil it on the gas stove, then turn a clean cup upside down on the spout, then put a clean bowl under the cup. In this way, the water dripping from the cup is distilled!

Wash the lid first, then boil the water, and the water droplets on the lid are distilled water.

1. Fill a liter stainless steel pot with about half of tap water.

2. Put a glass bowl in the water. Make sure it floats. The bowl should not touch the bottom of the pot.

3. If the bowl doesn't float, take it out of the water, place a round baking rack at the bottom of the pot, and put the bowl back in the water.

4. The water in the pot must be boiled before proceeding to the next step. This is to evaporate chemicals such as methanol and ethanol. Tong sail shirt.

5. Use a hot and cold barrier to produce a condensation effect. You can do this by flipping the lid of the pot and filling it with ice. Condensation occurs when hot steam hits a cold lid.

6. Bring the water in the pot to a boil. As the water continues to boil, it causes the steam to rise and condense on the lid of the pot. The condensate will drip into the bowl. Let the distillation process continue until there is enough distilled water in the bowl for your needs.

7. Pay attention to the stagnant water in the bowl. This bowl of water is hot, but it shouldn't boil. If the water in the pot starts boiling, turn down the temperature of the stove so that the water in the pot is boiling.

8. Remove your pot from the heat and remove the lid.

9. Remove a bowl of distilled water from a pot of boiling water. Be careful when doing this so as not to burn yourself. If you wish, you can let the water cool before taking the bowl.

10. Allow distilled water to cool before storage.

1. Prepare materials: Prepare a stainless steel pot with a volume of about 18L, tap water, glass bowl, round baking rack, pot lid, and ice cubes. 2. Fill the volume to half of the tap water on the left and right.

3. Put a glass bowl in the pot. Make sure the bowl is floating and doesn't touch the bottom. 4. Pay attention to the water collected in the bowl.

The water here is hot, but it can't be boiled. If boiling, turn the furnace temperature to low. <

1. Prepare materials: prepare a stainless steel pot with a volume of about 18L, tap water, a glass bowl, a round baking rack, a pot lid, and an ice marker.

2. Fill the volume to about half of the tap water.

3. Put a glass bowl in the pot. Make sure the bowl is floating and doesn't touch the bottom. If it doesn't float, place a round baking rack under the bowl.

4. Pay attention to the water collected in the bowl. The water here is hot, but it can't be boiled. If boiling, turn the furnace temperature to low.

5. Use the method of alternating cold and heat to create a condensation effect. Turn the lid upside down and fill with ice cubes, as the heat will condense into water droplets when it hits the ice.

6. Bring the water in the pot to a boil. After boiling, the steam will rise and condense at the lid. It then drip into the bowl and wait until the bowl has collected enough water before it stops condensing.

7. Remove the pot from the stove and remove the lid.

8. Take the distilled water bowl out of the pot. Be careful not to burn your hands. You can let the water cool down before moving it.

Need to prepare: a small bowl, pot, water, ice cubes.

3. Heat the water in the pot below, as shown in the figure below.

4. Next, put the lid of the pot on the pot upside down, and put a few ice cubes on the lid.

5. Finally, take out the small bowl and get distilled water, as shown in the figure below.

1. Take two bottles. The neck of one of the bottles needs to be bent slightly to prevent the distilled water from flowing back. 2. Fill one bottle with tap water, stick the bottlenecks of the two bottles together, and seal tightly with a pipe tape.

3. Fill a stainless steel pot with boiling water and distill the water. Just cover the amount of water in the bottle below. Tilt the bottle thirty degrees against the rim of the pot.

1. Take two bottles. The neck of a bottle needs to be bent slightly to prevent the distilled water from flowing back into the jujube bridge.

2. Fill a bottle with tap water, stick the bottlenecks of the two bottles together, and seal tightly with a pipe tape.

3. Fill a stainless steel pot with boiling water and distill the water. Just cover the amount of water in the bottle below. Tilt the bottle thirty degrees against the rim of the pot.

4. Put an ice pack or ice wrap on the bottle on it. This creates a ratio of hot and cold to liquid silverstone, allowing the steam to condense. Continue the coagulation process until enough moisture has been collected.