Both the router and the cat have been factory reset, what to do

Just set up your router again.

Here's how to set up your router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

5. According to the setting wizard step by step setting, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

6. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

No, the router reset can only clear the parameters of the router, it has no effect on the optical modem, if the router needs to be used normally, you also need to reset the parameters of the router, the following describes the router setting steps:

2. Then open the browser of the computer, enter the login address and login password of the router, and the specific login IP and password can be looked at the label on the back of the router.

3. After entering the router, there will be a setup wizard, first fill in your broadband account and password.

4. Then set the wireless name and connection password.

5. After the successful setting, a prompt will appear for the successful setting, and it will take effect by restarting the router.

Summary. After the factory reset, you need to set up your wireless router again.

Does the cat connect to the wireless router, do you do this:

Plug in the wireless router, don't pick up the cat first, reset the wireless router (restore the factory), connect the computer to any LAN port of the wireless router, enter the router gateway address in the browser address bar (on the label behind the router), enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method.

Then set the SSID, encryption method, and password. Save, restart.

After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

How do I connect the optical modem after the router is factory restored?

This question is up to me, it takes a little time to type, so please be patient.

After the factory reset, you need to set up your wireless router again. Does the cat connect to the wireless router, you do this: plug in the wireless router, don't pick up the cat first, reset the wireless router (restore the factory), connect the computer to any of the wireless routers, enter the router gateway address in the browser address bar (there is a label on the chain head behind the router), enter the settings page, and set it according to the pppoe (adsl virtual dialing) method.

Then set up the SSID, encryption, and password. Save, restart. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

Here's how to factory reset your router and get back online

Operating environment: dellxps13-9305, win10, router version.

1. Check the router's settings**.

<>3. Then, according to the prompts on the page, first set a "administrator password" (login password) for the router.

4. Set the Internet access parameters, if the "Internet access mode" is detected: broadband dial-up Internet access, you need to fill in your home's "broadband" and "broadband password" below, as shown in the figure below.

<>6. Set up a wireless network, and according to the prompts on the page, set a "wireless name" and "wireless password" for your router.

7. After the setting is completed, the router will automatically apply the configuration information just now.

Hello, after the router is factory reset, it needs to be reconfigured to surf the Internet. Here are the general steps:1

First, make sure your router is properly connected to the network and plugged into the power core. 2.On your computing cracker or mobile device, open the Wi-Fi settings and find and connect to your router's default wireless network.

The default network name and password of the router are usually marked on the back or bottom of the device. 3.Open a web browser and enter your router's default IP address in the address bar.

Common IP addresses are or, and the specific IP address needs to refer to your router's user manual or the label on the back of the device. 4.Enter the default username and password to log in.

This information is usually also noted on the back or bottom of the router. Common username and password combinations include "admin admin", "admin password", etc. 5.

Once you have logged in, you need to configure your network by following the information provided by your ISP. Usually you need to select PPPoE and then enter your broadband username and password. If you're unsure, you can contact your internet service provider.

6.Set up a wireless network. You can set a new wireless network name (SSID) and password in your wireless settings or wireless security settings.

7.Save and apply the settings. After that, your device should be able to surf the internet normally.