How to clean the shower when it is blocked, how to clean the shower when it is blocked

With the improvement of everyone's living standards, nowadays, almost every household has installed a water heater, and the shower has become one of the indispensable supplies in the bathroom. The shower is easy to clog after being used for a long time, which affects the size of the water flow, and there may be no water. So how to clean the shower when it is blocked?

How to clean the shower when it is blocked.

Pour the vinegar into the basin, and then put the shower in it to soak, and the scale can be removed after more than ten minutes, so that the shower is clear. You can also carefully check which parts of the shower are blocked, and then use a needle to pierce the blocked holes until there are no impurities, but be careful not to puncture the shower. If the shower is clogged due to rust, you can use lubricant to clean it.

What are the precautions for using a shower.

1. Don't use too much force when opening and closing, and don't use force when adjusting the amount of water, otherwise it is easy to damage the faucet, just turn it on and off lightly or turn it gently. Even a traditional faucet doesn't require too much force. In addition, be careful not to use the faucet as a handle and the shower stand as a handrail to support it.

2. After use, the connecting pipe of the shower should be kept naturally stretched, and it should not be wound and knotted. Pay attention to the joint position part of the connecting pipe and the faucet should not produce dead angles, otherwise it is easy to break or damage the connecting pipe. You should make a good habit when showering, and wipe the shower with a towel at the end of the shower to prevent the remaining water from forming scale.

If it is a rubber outlet, you can rub it with your fingers, and if it is made of metal, you can use a paper clip to dredge the water hole.

3. Do not place it in a high-temperature environment, if the temperature is higher than 70 degrees, it can accelerate the aging of the shower, and it can not be placed in a place with strong ultraviolet rays, which will shorten its use. Therefore, the place where the shower is installed should be a little far away from the bath bomb lamp electrical appliances, and cannot be directly installed directly below the bath bomb, and it is best to be spaced more than 60 centimeters apart.

The shower at home may be clogged after a long time, because some debris or minerals in the water will accumulate more, which will block part of the water outlet hole of the shower, resulting in less water output. After this happens, do not use strong acidic things to clean up, which will cause corrosion to the shower itself. It is best to deal with the shower at home regularly, and generally clean it once in half a year or less, so as not to suddenly block the shower and affect your mood when showering.

Before cleaning the shower, make sure that the shower is blocked badly, first observe the water coming out of the shower, and determine how many small holes in the shower are blocked. If it is relatively slight, you can use a needle or other thin object to pierce the small hole, but be careful not to puncture the small hole in the shower. This method is the most straightforward and simple, but it is also a more cumbersome method that requires a little more care.

It is only suitable for those with relatively few blocked water outlets and strong hands-on ability in fine movements. Then if the outlet hole is blocked more, it is not suitable for this method, and the effect may not be good if it is too hard.

If there are many blocked holes, vinegar can be used to solve this problem. You can pour rice vinegar into a pot, a little more, and you need to be able to put the amount of the shower that is not over, and put the side of the shower with small holes in it. After about ten minutes, the small hole in the shower will be dredged, if the effect is not ideal, you can soak it for a while, and then after all the shower has been cleaned up, rinse the shower with clean water.

If it is a more serious blockage problem, or even the shower is a little rusty, maybe the above two methods will not work, then you need to use a special rust removal lubricant, this lubricant can be very effective to remove the rust on the shower. In the process of use, it will not hurt the metal, but can effectively separate the metal and the rusty contact surface, and after removing the rust, it can also form a special protective film on the metal surface of the shower, so that the shower is no longer so easy to rust. However, some showers that are too rusty to seriously affect the use of showers, it is recommended to change to a new shower.

Usually, after the shower is used, it needs to be placed. It is best to avoid the bath bomb when installing, and do not let the shower be installed directly under the bath bomb, which will affect the service life of the shower. Prolonged exposure of the bath bomb will increase the temperature on its surface, and it may be hot when used again.

It is best to stay away from the bath bomb, generally about 60 centimeters away from it. Keep it dry after use, often use a soft cloth to dip a little flour, and often wipe the surface of the shower, so that the shower can keep it bright for a long time.

What should I do if the shower has scale and less water? Today I will teach you to quickly remove limescale from the shower.

There is a rotating switch for the rain shower head, which can remove the head and clean the dirt inside.

The shower is cleaned with reed water, then soaked in white vinegar, then with lemon descaler, and finally rinsed with water.

1. Manual cleaning: remove the mesh cover part at the shower head, clean it with a brush and then install it back in place. Some brands of showers are equipped with special shower head opening tools when the first time, which is convenient for consumers to clean and use.

2. Put the white vinegar and water in a ratio of 1:1, put the shower head in it and soak it for about 2 hours, then brush it with a toothbrush, and then rinse it with water.

3. Use citric acid descaler, spray it on the shower hole, wait for ten minutes and then rinse it with water.

4. If the metal of the shower is rusty and the blockage is very serious, then you have to use WD-40 rust removal and anti-rust lubricant. This rust removal lubricant separates the rust layer from the metal layer. It makes the rusty part of the contact surface with the metal, and leaves a protective film, so that the shower will never die of rust.

Precautions for the use of showers: rapid cracking

After removing the shower, put it into a small basin containing white vinegar and soak it for about two hours, brush it with a toothbrush after soaking, and then clean it with water; If there is hard water sediment, scrub with lemon slices.

In order to ensure that the shower head is not clogged, it is best to clean the shower head every six months or less, so that you no longer have to worry about the sudden blockage of the shower head when taking a bath, so that it will affect your bathing mood.

In order to ensure the service life of the shower head (shower), it is best for us to keep it not directly below the bath bomb when installing, and it is best to be more than 60cm away from the bath bomb, and often wipe the surface of the shower with a soft cloth with a little flour to keep it as new. Before each shower, use a towel to scrub the shower spout to prevent limescale from remaining.

If the shower head at home is clogged, you can use some life tips, such as: dipping it in vinegar, pricking it with a needle, using lubricant, etc.

1. Dip in vinegar.

After a long period of use, most shower heads get clogged because the limescale is clogged by the spout. If it is slightly clogged, remove the shower head and wash it. If the shower head is clogged for a long time and a large number of holes are blocked, we recommend that you prepare white vinegar, soak the vinegar in the head, and then soak it in the shower.

After soaking the vinegar for 10 minutes, the limescale can be removed from the head shower.

2. Use acupuncture.

If the nozzle in your home is only partially clogged, you can drip water first to check if the hole is clogged. After that, use a needle to puncture the clogged pores until impurities do not come out of the pores. But pay attention to the strength of the piercing.

3. Use lubricants.

Each nozzle has a different material and a different solution. If the head of the shower is rusty, it is recommended to use a descaling lubricant. This rust removal lubricant improves the permeability of the metal. Separate the rust layer from the metal layer and leave a protective film that won't corrode the shower.

Tips for cleaning clogged showers: use citric acid, baking soda and white vinegar.

1. Use citric acid

If the shower head is caused by limescale or rust, then you only need to have citric acid ready. Put citric acid into warm water to dilute the land belt, and then soak the bath head in the citric acid solution, generally soak for about 20 minutes, the dirt on it will slowly dissolve, and finally rinse it with water.

Citric acid can disintegrate alkaline residues, such as scale rust, etc., the shower head cleaned with it is as clean as new, and it can also inhibit bacteria and disinfect, and the shower cleaned with citric acid is more reassuring and reassuring.

2. Baking soda white vinegar

Pour baking soda and white vinegar evenly in a ratio of 1:1 into warm water, and then soak the shower head in warm water for about 10 minutes, which can also effectively remove the scale and blood rust on the shower head. However, this method is not recommended to be used frequently, because white vinegar has a certain corrosiveness, which can damage the shower head.

Causes of clogged shower heads

1. The quality of the shower head is not good.

The blockage of the shower head is mainly because the quality of the shower head is not good, you must choose the silicone texture when choosing the shower head, the shower head of this texture has a long service life, it is cheap, and it will not be clogged often, even if it is blocked, it is relatively simple to clean up.

2. The shower head is rusty and scaled.

The main reason why the shower head can become clogged is due to rust or limescale. If the selected shower head does not have the function of filtering the morning reed, then the pores of the shower head will breed a large number of bacteria over time.

One of the reasons for the long use of the shower is that the water quality is hard, and the water remains on the shower, and the scale is formed. So what should I do if the shower is blocked? Next, let me take you to take a look.

1. Use acupuncture: If some of the small holes of the shower are blocked by foreign bodies, you can use needles to prick the small holes to remove the foreign bodies, but it should be noted that if the area of foreign bodies is large, it is best not to use needles, otherwise the needles may sink into or be broken.

2. Soak with vinegar: If the shower has been blocked by foreign objects for a long time and the holes are completely blocked, you can use vinegar to soften the substance, and then prick the foreign body with a needle. The specific method is to prepare some white vinegar first, then pour it in a basin and dilute it with water, and then put the shower inside.

3. Use lubricant: The shower is blocked by foreign matter, you can buy a lubricant specially used to clean the shower, separate the rust layer from the metal layer, and then remove the rust to make the shower smooth again.

4. Wipe with a towel: The appearance of the hunger shower is old, it has been used for a long time, if it is blocked, wipe it clean with a towel first, and then prick it with a sharp object, and finally remember to rinse it off to prevent residual bacteria in the flower such as limb sprinkler.

1. Pour out the sprinkler head debris to clean the water inlet for a long time, and it is difficult for some granular objects in the water inlet pipe or tap water to come out of the water outlet hole, so it is easy to block the water outlet hole, remove the shower nozzle, and gently shake the water inlet downward to pour out the sundries inside. When disassembling the nozzle, take care to save the accessories.

2. Clean the dirt of the nozzle.

1) Use embroidery needles and vinegar.

The shower nozzle diverts the water column from multiple outlets, which reduces the impact on ** and can also achieve a massage effect. When cleaning, you can make use of small items around you, such as embroidery needles for sewing. Pierce the needle into each outlet hole one by one to make the scale fall off from the inner wall of the outlet hole, and then pour the water into the sprinkler from the water inlet, shake and wash and pour out the water to make the scale fully cleaned.

The method described above does not require too complicated tools, and the more troublesome point is to clean them one by one. But when cleaning, you need to disassemble the shower head, so how to break the shower head that cannot be disassembled? Many people know to use vinegar to clean the inner wall of a kettle, because vinegar can dissolve limescale, and shower head cleaning can also be used in this way.

2) Soaking. Choose a container that can put down the sprinkler, pour in white vinegar, toilet cleaner or special limescale cleaner and other weak acids, put the end of the sprinkler head into the water for a period of time (3-4 hours is appropriate), brush it with a small toothbrush or other clean brush, and then rinse with water. One thing to note with this method is that weak acids should be used instead of strong ones.

The surface of the nozzle generally has an electroplating layer, or other parts are made of metal, which will cause corrosion to the nozzle when encountering strong acids.

3) Wipe off limescale.

After rinsing with water, wipe the scale around the hole and on the surface with a rag, and if you encounter a more "stubborn" sediment, do not use a needle, scrape with your fingernails until it falls off, and then clean it with a rag. Of course, in order to maintain a long service life, it is not enough to pay attention to the cleaning of the shower head, especially for the nozzle with the electroplated surface, but also to carry out daily maintenance: after use, often wipe it with a clean soft cloth (preferably with a little flour to wipe the surface), so that the surface is as smooth as new.