The local connection of the fast wireless router is connected, but the network cannot be connected

Again, the problem is with the router.

Ping first

Make sure your network card is fine.

Then run ipconfig all in the command line window to see the IP allocation. The correct situation should be assigned to the DNS parameter, if it is not assigned, it means that the route is not dialed up.

Then set it on the router, and if it doesn't work, restore the factory settings according to the manual.

If it still doesn't work, then find a JS that sells your route.

You used to use the cat directly to dial the number with the computer, but now with the router, it becomes the router dial-up.

First of all, check whether the router dialing is normal: you can see the dialing status in the router status.

Second, check the connectivity between the computer and the router: ping the router to see if it can communicate.

If the above two points are normal, then it should be fine.

The ground connection is displayed normally.

It means that your computer can be connected to the router.

Make sure your IP address is correct.

There are many reasons why you can't get online.

Or. Enter the route:

Whether your dialing settings are correct and whether you have successfully dialed the number.

If you can't, please check the cat, etc.

Whether the route has a static IP address set to surf the Internet, you can add your address to it.

Or change to dynamic allocation, and re-flash the IP and cmd

ipconfig

release

ipconfig

renew doesn't know it, so I'll re-computer.

Please check the following items:

Is your external network cable pulled out directly from your modem (cat)?

If yes, :1Whether the network cable is plugged into the WAN jack of the router.

2.In the router, whether you have selected the ADSL account (PPPOE) through the setup wizard to access the Internet and filled in the correct ADSL account and the corresponding password.

3.If the above two items are true, please check whether the IP address or MAC address is filtered in the router's security settings or network parameters.

The general solution for the above three points is: plug in the power cord of the router, press and hold the REST button (hole) on the router for more than 5 seconds, and after the router restarts, log in to the router with the default account password and configure it correctly (you only need to set the Internet mode, and the rest are default).

If the network cable is shunted down by the previous router, then there are two ways.

1 You want to keep up with the users in your router in the same LAN: Plug the network cable into the router Any hole except the WAN port Log in to the router Select DHCP service to disable it No other settings are required.

2 You don't want to keep up with the users in the router in the same LAN: plug the network cable into the router WAN port and then log in to the router Setup Wizard Select the Internet access mode "Ethernet broadband" Static or dynamic IP address You can choose by yourself Then the dynamic IP only needs to modify the IP address of the router and cannot be in the same network segment as the previous router That is, it can be modified to (the method is the router network parameters and then modify it directly) The static IP requires the user to manually enter the IP address and DNS server It is recommended not to select this option.

Is the dialing success in the route? Don't tell me I didn't have a network cable that didn't connect the router in.

At present, more and more people use wireless routers, and the problems encountered are becoming more and more strange, some of which are actually minor problems that we can solve ourselves. For example, when using wireless, you can't connect after encrypting the router's wireless, or you can't connect after changing the password. In response to these problems, here I will tell you how to set it up.

Step Method.

Go to the wireless network connection properties and delete all wireless network configurations in the preferred network.

The specific settings are as follows:

Right-click on "Network Neighbors" - select "Properties" to enter the network connection page.

Right-click on "Wi-Fi Connection" - select "Properties" - click on "Wi-Fi Configuration" There is a preferred network here, delete all the wireless network names in the box below the preferred network. This avoids crosstalk between them.

Search for the connection again (to enter the correct wireless password, the letters are case-sensitive). If you still can't connect, change the safe mode. It may be that his computer department supports this encryption.

If you want to change the password or encryption method, you need to go to the router's settings page. The following steps are as follows to set up the JCG JHR-N815R router:

Connect the router with a network cable, then enter it on the browser to enter the router's settings page, and click "Wireless Connection". Go to the wireless settings page.

Here you can change the name of the wireless network (i.e. SSID), as well as the channel.

Click "Security Settings" to enter the security settings page and set the wireless password.

If the security mode is "WPA Personal" or "WPA2 Personal", then the password must be more than 8 digits of numbers or letters, note: the letters here are case-sensitive.

Note: There is a place to pay attention to here, that is, "safe mode" here, the default security mode at the factory is "WPA2 personal", this security mode is more advanced, if your system is Windows XP Service Pack 2, then your computer does not support this advanced security mode, you need to choose "WPA personal" this security mode.

Precautions. The above is the place where the router needs to be modified after wireless encryption, and the wireless password settings of all routers are the same, as long as you look at the settings of this router, the others are almost the same.

I hope my answer helps.

o( o look!)

After the fast wireless router is factory reset, the wireless router needs to be reconfigured for normal use.

How to configure a wireless router:

1.The router is connected to the network.

2.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

6.The configuration is complete and you can enjoy the network.

Is your school assigned an IP and bound to an IP, what is your network structure, do you want to expand the network through wireless routing, and network sharing?

Does your school need software for account verification?

If so, there will be trouble, the wireless router needs to be set up to connect to your school's **, and it is set to the IP assigned by your school to access the data, but after assigning this IP, your own machine cannot be assigned (because the IP is assigned to the route, and if it is not assigned to the route, the router will not be able to connect to the network. Of course, you can also use the address translation function of the router, but if your school has an account verification mechanism, I'm not sure if the software will detect the IP binding of your own machine and other things, so the route can't be verified. So, the connection will fail.

Of course, if you're lucky, it's okay to set up the first conversion function of the route, so you're in luck.

The first factory reset can't go online, and whether the problem still exists in the second factory reset is waiting for you to try;

After the factory reset, the route needs to be reconfigured.

Open your browser and enter it in the address bar.

Login (the account and password are generally admin by default).

Locate the setup wizard.

Then follow the guided steps to set it up.