How to open the new Fit run in period? How to open the new Fit run in period?

Walk for an hour or two a day, control the throttle below 2500 rpm, turn the steering wheel and don't hit the end, it's almost good, my 3000 one.

To do maintenance, landing to now are plus 97, direct injection in the cylinder has high requirements for oil, domestic quality, only 97 can be slightly.

Put a little heart. However, the 4S shop introduces your maintenance**, there is no need to see, just change the oil, oil grid, gasoline grid, and air grid.

1. Preheat in advance. Today's gasoline cars rarely need hot cars except for long parking and extremely cold environments, but new cars are still available.

It is better not to skip this step, and preheating for 1-2 minutes after each car can provide better oil film protection between dry parts.

2. Shift gears in time when driving, especially when novices are on the road, especially to avoid the occurrence of low-gear high speed and high-end low speed.

Do not use one gear for a long time.

3. Speed limit. There is no clear standard for the speed limit of new cars, and it is generally recommended that the speed of the vehicle should not exceed 100km h, especially for the first 3000 miles, and do not pull the high speed for a long time.

4. Avoid the vehicle running at full load. A full load of the vehicle will undoubtedly increase the load on the engine, so it should be avoided as much as possible in the early stage.

5. Avoid emergency braking. In addition to the large impact on the braking system, emergency braking also increases the shock load on the engine and chassis.

Anti. 7. Don't use a new car as a "coach car", and don't overuse it.

After 3,000 kilometers, it is still recommended to pull the high-speed appropriately. Pulling the high speed before preparing for the first warranty can improve the fluidity of the oil, which is better.

Clean the iron filings and sludge in the engine. The second maintenance after the first warranty can not be ignored, and it can only be done smoothly through the running-in period.

After the long stage of using the car to lay the foundation.

1.Avoid overloading: Running a new car at full load can cause damage to the components.

Therefore, in the first 1000 km, domestic cars can not exceed 75 -80 of the rated load; Imported cars cannot exceed 90 percent of the rated load. In addition, try to choose a better quality road surface to avoid excessive vibration, collision or emergency braking, and reduce the load on the body and power system.

2.Do not remove the speed limiter in advance: The speed limiter is a throttling device installed between the carburetor and the intake pipe.

The driver should not remove it in advance, but after the initial 1000 kilometers in conjunction with the initial driving maintenance. Imported cars generally do not add speed limiters, and the driver completely controls the speed by himself.

3.Avoid running long distances: Honda Fit running long distances will increase the continuous working time of the engine, resulting in increased wear and tear of parts.

4.Avoid emergency braking: Emergency braking not only impacts the braking system during the run-in, but also increases the shock load of the chassis and engine, so do not use emergency braking within the initial 300 kilometers.

It should be stated that the practice of "first leaving and then braking" is a measure to protect the engine during the run-in period and in the event of an emergency situation (emergency braking). Do not use it as a good habit for a long time, when the vehicle has passed the run-in period, from the clutch maintenance aspect, it should be "brake first and then leave", there are many novices in learning to drive, because of the fear of stalling, never forget to pedal clutch, to slow down on the clutch first, even if it is hung in high gear or low gear driving, but also for the convenience of shifting, the clutch does not leave the foot. This kind of braking and shifting may make the car drive more smoothly for novices, but it will cause a lot of damage to the clutch.

1. The mileage of the car at the beginning of the run-in period is generally less than 500 kilometers, and the speed should not be too fast, but should be kept at 60-70 kilometers, and the speed should not exceed 2200 revolutions.

2. When the mileage reaches about 500-1000 kilometers for the middle of the run-in period, the speed is increased from 60-70 to 90-100 kilometers per hour, and the speed is below 2500 rpm is the best. This facilitates the run-in.

3. When the new car runs long distances during the run-in period, the continuous working time of the engine will increase, which is easy to cause wear and tear of the parts. The run-in period has a great impact on the service life and fuel consumption of the car in the future, the owner must take care of his car, and after the run-in period is over, it is necessary to maintain it in time.

1.When driving the vehicle, you should try to avoid high-speed driving, long-distance wheel driving and full load driving, and try to preheat the engine before driving, so that the internal running part of the engine can be fully lubricated.

2.First of all, the speed of the vehicle and the engine speed are strictly controlled. During the run-in period, the maximum speed shall not exceed 90kmh, and the engine speed shall not exceed 3000rpm, so as not to cause excessive load to the engine, gearbox and other components, and at the same time try to avoid long-term low-speed driving of the vehicle, and shift gears in time during driving, so that the gearbox can be completely run-in.

3.During driving, rapid acceleration and braking operations should be avoided as much as possible, as such operations are prone to cause great impact on the engine, gearbox, braking system, chassis and suspension. During driving, the driving speed should be kept as constant as possible, and refueling and braking should be slow.

4.Choose high-quality lubricating oil: choose low-viscosity and high-quality lubricating oil to make the friction surface lubricated well and slow down the wear of parts.

5.Warm up ahead of time. In addition to long parking and extreme cold environments, it is best not to avoid this step for new cars. Warm-up for 1-2 minutes after each drive provides better film protection between dry and closed parts.

6.Shift gears in a timely manner while driving, especially if you're new to the road. In particular, avoid high speeds at low speeds, low speeds at high speeds, and do not use one gear for a long time.

7.Don't use your new car as a "trainer car" and don't overdo it. After 3000 km, it is advisable to pull the highway appropriately.

Pulling the high speed before preparing for the first service can improve the fluidity of the oil hood and better clean the iron filings and sludge inside the engine. The second maintenance after the first maintenance should not be overlooked. Only by successfully entering the racing phase can you lay a good foundation for long-term driving in the future.

8..Avoid running the vehicle at full load. A full vehicle load will undoubtedly increase the load on the engine, so it should be avoided as much as possible at an early stage. Avoid emergency braking. Emergency braking not only has a great impact on the braking system, but also increases the shock load on the engine and chassis.

During the run-in period, try to drive as slowly as possible, don't step on the accelerator, don't drive on the empty road, and pay attention to the maintenance of the car on time when you usually drive, the new Fit this car runs in for 5000 kilometers and is almost a loss.

When driving a Zhongsheng car, you must slow down, you must read more manuals, understand the functions of the car, so that you can run in slowly, you must take the sun to observe the rearview mirror, and turn the turn signal when turning.

You can go on the highway, you must drive at a constant speed, you must pay attention to safe driving, you must fasten your hunger and hunger belt, and you must choose the driving speed that is not the same according to different road conditions.

Within 3000 kilometers, it is recommended not to exceed 80% of the maximum speed of the car; Some people in the industry believe that the maximum speed of the car cannot exceed 70%, and the engine speed cannot exceed 3000 rpm.

Fit's run-in method:

Preheat in situ for 1-3 minutes after starting the cold car; The load should be appropriately reduced; Avoid sudden acceleration or sudden braking; Timely speed change, short-term fixed speed driving; Drive for more than 2 hours continuously, stop and go for 20 minutes.

Precautions for the Fit run-in period:

Driving a new car with a full load can cause damage to parts. Therefore, in the first 1000 kilometers, domestic cars can not exceed 75-80% of the rated car load; Imported cars cannot exceed 90% of the rated load capacity. In addition, try to choose a better quality road surface to avoid excessive vibration, collision or emergency braking, and reduce the load on the body and power system.

Millions of car purchase subsidies.

The new car should pay attention to starting the engine correctly, and be sure to wait for the end of the self-test before the key starts at the beginning, and it is not possible to start it all at once. The first key to the run-in of the new car is to monitor the various signal lights of the dashboard at any time, and the fault display must be dealt with immediately in case of bad service.

It is necessary to pay attention to safety issues, pay attention to safe driving in the air of the year, do not overload, do not add too much oil at one time, choose better quality oil, check the oil frequently, and also check the coolant.

The Fit run-in period is 3000 km. Because the work of new automotive machinery and equipment is not comfortable enough to cooperate with each other, the whole process may have an impact on the cause of metal material slag. Therefore, you must grasp the common problems of running in the lease term.

1. Do not stop in an emergency.

The emergency brake pedal seriously increases the impact force on the engine and suspension, and it is also a huge hazard to the car's braking system.

2. It cannot be used by car.

In particular, those who love floor oil will greatly increase the operating load of the engine, which is likely to lead to premature muscle strain of the piston rod and engine crankshaft parts. The engine speed ratio is proposed to be kept within 3000r min.

3. The loading should not be too heavy.

The increase in load and fuel consumption are trivial, mainly because the burden of high toughness will accelerate the destruction of parts. The total output of vehicles and goods is controlled within 70% of the rated load capacity.

4. Apply high-quality fuel.

In strict accordance with the fuel model proposed by the manufacturer, the fuel quality is unqualified, which will lead to carbon deposition on cylinders, automobile spark plugs and other parts.

5. Preheat the cold car before starting.

The function of car preheating is to prevent engine damage by slowly rising the engine degree to the operating temperature.

6. The gear should be suitable.

Owners of manual transmissions must pay attention to the fact that the gear and speed ratio should be consistent, such as high-speed rotation of low gear, or high-end low speed ratio full digging is not good.

Available years: 2020, 2018, 2016 and earlier.

Millions of car purchase subsidies.