What is the method of changing one gear and other gears in a manual transmission car?

The methods and techniques for shifting gears are as follows:

1. Shift gears in a timely manner according to the speed of the car. Under normal circumstances, the first gear is hung at the start, and then the second gear is changed after driving a few meters; When the speed reaches more than 20 miles, 35 miles and then shift to three gears; The speed reaches more than 35 miles, and 45 miles is changed to four gears; The speed reaches 45 miles or more, and changes to five gears. The above is an ordinary five-speed transmission car, for a car with more than 6 gears, a gear can be added for every 15 miles of speed increase.

In addition, when changing gears, you should be optimistic about the speed of the engine, and it is best to change gears in time when it is about 2500 rpm.

2. Sometimes when driving the car, you find that the vehicle is a little trembling, which means that the engine is running at low speed and high load, and you should immediately lower one or two gears according to the actual situation.

3. At the same time of shifting, the clutch and throttle should be well coordinated, and the clutch should be lowered and then release the accelerator pedal, and then quickly shift to the corresponding gear. After shifting gears, let go of your hand immediately, and do not put it on the gear lever (commonly known as the gear target) for a long time, otherwise it is easy to damage the gear lever.

4. Master the correct gear shifting hand. Many drivers often ignore the hand shape of the shift, and sometimes use two or three fingers to change gears, which is very irregular and unsafe. The correct shift is to cover the head of the gear target with your palm down, grasp the gear target tightly with five fingers, and then shift gears.

5. Shift gears in place. Sometimes we drive for a long time and change gears very casually, and lift the clutch without the gear being aligned, which is very damaging to the transmission. Therefore, when changing gears, you must shift in place, and when shifting gears, you must press the clutch to the end.

Generally speaking, hang 1st gear, go left and then move forward to hang gear; Hang 2nd gear to the left and then push down to hang gear; Hang 3rd gear and push straight up on the basis of returning to neutral; Hang 4th gear and push straight down on the basis of returning to neutral; Hang 5th gear, push straight to the right and push up again.

6. Familiar with the special reverse gear hanging method. Different vehicles have different ways to hang reverse gear, and some vehicles push straight to the right and then pull down to hang gear; Some vehicles have to keep left in the position of 1st gear, that is, they are pushed to the left one block more than 1st gear and then gear forward; Some vehicles need to use the middle finger and ring finger to lift the button under the gear target, and then push the gear forward to the left; There are also vehicles that need to press the gear target and then push left forward or right backward to get into gear.

<> "Car Shift with Manual Transmission.

The shift sequence must be 1st, 2nd, 3rd, 4th, and 5th. Gear skipping is not recommended.

The order of downshifts is based on the speed per hour. Depending on the car condition, the general speed is below 1500 rpm and needs to be downshifted. Choose the gear that's right for you based on speed and real-time traffic conditions.

Shift gears at the right time according to the speed of the vehicle.

Ordinary five-speed transmission cars generally start in first gear, and then shift to second gear after a slight increase.

Shifting into fourth gear is worth it when the speed is steady at 35 to 45 mph, and when the speed is above 45 mph, shifting fifth gear is worth noting.

Gearshift tips for manual transmission cars.

When changing gears, you must keep in mind the principle of "accelerate first when upshifting, and slow down first when downshifting".

Before downshifting, the clutch pedal must be pressed all the way down, and the gear lever must be operated gently.

Shift gears according to the speed of the car.

In general, you start in first gear and then change to second gear after driving a few meters. When the speed reaches 20mph or higher, shift to third gear after 35mph. Changing four gears at a time to reach speeds of more than 45 mph, and changing more than five gears is a common five-gear shifting model and a sixth-gear car.

The key to driving a manual transmission car is shifting gears.

The key is to shift gears in time according to the speed at which the car is traveling. Only by being fast and accurate can you drive more freely.

When the vehicle reaches 20 mph or higher, shift into second gear at 35 mph.

The shift technique of a manual transmission car accelerates first when upgrading, and slows down first when downshifting.

The first is to keep in mind the principle of "accelerate first when upshifting, and slow down first when downshifting".

Before downshifting, "retract" the throttle and reduce the speed of the car.

When changing gears, try to accelerate with "two feet off".

The specific operation steps of manual transmission car shift are as follows:

1. Press the brake pedal of the manual transmission car.

2. Press the one-button start button of the manual transmission car.

3. The instrument of the manual transmission car lights up and the vehicle starts.

4. Put the gear lever of the manual transmission car in the M position to enter the manual mode.

5. Push forward the manual transmission gear lever once to increase one gear.

6. Push the manual transmission lever backward once and lower it by one gear.

7. Press the manual transmission car accelerator, and the vehicle will start.

The following is the manual shift operation:1The vehicle hangs 1st gear and pushes forward to the left to get into gear; 2.

Hang 2nd gear, go left and then push down to the gear; 3.Hang 3 gears and push straight up on the basis of back to neutral; 4.Hang 4th gear and push straight down on the basis of returning to neutral; 5.

Hang 5th gear, push straight to the right and then push up (refer to the gear mark of your own vehicle for details). The following is the introduction of the gears: Block:

It is used when starting normally or climbing very steep slopes. The speed of the vehicle is generally 10 km/h; Gear: Excessive gear for acceleration after starting, or low-speed forward use, the speed is generally 20 kilometers per hour; Block:

This gear is used at 20-40km per hour U002FH, and it is often used when driving in urban areas; Gear: Use this gear when the speed is 40-60km U002FH; Gear: The gear can be used at a speed of 60km U002FH or more; Block:

Neutral, parked and idling when running; Gear: Reversing gear, reversing in this gear after the vehicle is stopped.