How to change the spare tire of a car, how to change the spare tire of a car

It's good to pull your car on the side of the road, pull on the handbrake, and turn on the double flashes to warn the passing vehicles. Place warning signs 50-150 meters directly behind your car. Take out the tire wrench, jack and spare tire from the trunk and remove the bolt cap of the tire with a tool plier.

Use a socket wrench to loosen the tire bolts a little. Use a jack to lift the tire. Pull out all the bolts and remove the broken tire.

Swap the removed tire with the spare tire. Attach the spare tire, first tighten the four screws by hand until the hand can not be twisted.

Hello, car spare tire words are. There are full-size and non-full-size two full-size then with our normal tire size can be installed at will, each tire damage directly to the tire on the line, if it is not full-size, that is, than you, normal tires are smaller, this spare tire can only be installed in the rear wheel, if the front wheel is damaged, the front tire needs to be removed, and the rear wheel is reversed, and then the spare tire is installed on the rear wheel, hope.

First of all, if you are on the road outdoors, park your car, turn on your twin flashing lights, and put up warning signs to warn cars and people. Loosen the tire screws diagonally to reduce the pressure on the wheel. Then find a place with a triangular groove under the car, go down the line, prop up the jack out of the place, and take the tire off.

Replace the tires. The same diagonal method fixes the screws, and then puts the jack down, and after the car is lowered to the ground, the car screws can be tightened.

First of all, stop the car in a safe and suitable place to turn off the lights and double flash, find the tools you need, check the tire pressure of the spare tire, and then unscrew the tire screws that need to be replaced, and then use the jack to lift the car up, it is best to pad something under the car to prevent the jack from collapsing, and finally it should be noted that after the change, the cycle tightening screw twice can play a role in reinforcement.

The first step is to prepare the tools and equipment needed for the whole process of disassembling car tires, a tire wrench, a small hook, both of which can be found in the trunk of the car, and a jack.

The second step, the disassembly of the tire screw cap, take out the small hook, hook the hole of the screw cap with a small hook, and then pull it out to remove the screw cap, a total of 5, take it off one by one, the third step, take off the screw cap to be placed in a small box to avoid loss.

Fourth, the initial loosening of the car tire screw, take out the tire wrench, use the tire wrench stuck on the screw, and then turn counterclockwise to loosen all 5 screws.

The fifth step is to support the place where the tire needs to be disassembled, take out the jack, find the support point of the stiffener in the place of the chassis, and then use the jack to support the vehicle.

Sixth, take out the tire wrench again, disassemble the 5 screws that were loosened before to fix the tire, and put the disassembled screws in the previous small box.

Step 7: We can remove the tires of the car, hold both sides of the tires of the car with both hands, and then lift them out.

Here's how to change your car's spare tire.

1. First take out the spare tire, the screws are tightened, and you have to use your feet to loosen it.

2. Then put on the jack, and then remove all 4 screws, remember to put the screws, so as not to find it for a while. Secondly, put on the jack, and then remove all 4 screws, remember to make the screws hungry and put them well, so as not to find them for a while.

3. After replacing the new tires, you can put on the screws, and tighten the four screws by hand first.

4. Then put down the jack and tighten the screws with tools or Huru.

Find a safe place to park and try not to park on dirt or grass as much as possible, your jack may sink into the dirt and become unstable, try to avoid hills to prevent your car from rolling. Before changing tires, turn off the engine and use the emergency brake or parking brake. Wheel blocks or heavy stones can be placed behind the other side of the side that is lifted to prevent your car from rolling.

Take out your jacks, spare tires, and tools, and if you have never used a jack, spare tire, or tire tool before, consult your owner's manual to check where they are. Once you've found these essentials, we recommend that you try them out and familiarize yourself with how to use them so you can easily navigate the next few steps. Waiting on a dark, rainy night to learn how to use a tool can be frustrating and even dangerous.

We recommend that you practice when your tires are not deflated so that you know how to perform the task.

Loosen the lug nuts slightly before you jack up your car, and if your car has wheel covers (hubcaps), remove them first using a screwdriver or the flat end or lug wrench of the jack handle. Refer to your owner's manual for the best position to secure the jack and follow these instructions carefully! Turn your car at least 6 inches, or in any case, you will need to remove a flat tire.

If you find instability, lower your car to reposition the jack, never place the jack under the axle or suspension parts.

Remove the lug nuts and wheels, trap the front or use a lobe wrench to remove the nuts, and place the lug nuts where they won't be lost, such as on the inside of the door. Pull the wheels down and set aside. Remove the flat tire with both hands, pull the tire towards you and place it under the car in case the jack is unstable and falls off the car.

If it is difficult to remove the tire due to rust, use a hammer to hit the rubber or use liquid penetration to loosen the joint.

Place the spare tire in front of the wheel well, align it with the wheel bolts, and add the lug nuts, tightening the lug nuts as clockwise by hand as possible. Then pick up your wrench and tighten the bolt tight enough to secure the tire before lowering it to the ground. Do not tighten completely.

Slowly lower your vehicle to the ground and remove the jacks and stops. Tighten the lug nuts in the correct order as much as possible. Many spare tires are not full-size plain-based pure tires, and these smaller spare parts cannot travel at normal speeds and can only travel short distances.

For instructions and warnings for driving with compact spare parts, please refer to your owner's manual.

Be sure to choose a relatively flat road surface, open a double flash, place warning signs around the bridge to sell, take out the spare tires and tools, take the bolt cover on the original car, loosen the bolts, and then lift the vehicle with a jack, remove the original tires on the car, and then press the wheel tour town tire used by the Min grinding teasing.

The correct way is to remove the previous tires and then use a jack to jack the car, and then use screws and wrenches to replace the new spare tire on the car.

The old Duan Jing tires should be dismantled with a wrench first, and then the car should be lifted up with a jack, and then the tire should be fixed on the car with a screwdriver and screws.

To change the spare tire of the car, first park the car in a safe place, turn on the double flash, and place the tripod;Take out the spare tire and tools;Remove the plastic cover from the bolt;Loosen the bolt diagonally counterclockwise with a socket wrench;Hold up the jack;Remove the tires;Attach the spare tire;Screw the screws to secure the tire;Put down the jack;Finally, use the tool to tighten the screws with the maximum force of your hands;Complete the replacement of the spare tire.

Detailed explanation of the steps for changing the spare tire of the car.

1. Park the car in a safe and stable place, turn on the double flash, place the tripod, warn the rear that there is a situation here, and pay attention to avoidance. (On conventional roads, it should be set 50 meters to 100 meters behind the car; On highways, it should be set up 150 meters behind the car; In case of rain and fog, the distance should be increased to 200 meters; ）

2. Take out the spare tire, wrench, and jack. (The most common spare tire is placed at the bottom of the trunk, and some SUVs and off-road vehicles have spare tires placed at the bottom of the car, and some are plug-in).

3. Start disassembling the tires. Loosen all the tire screws that need to be replaced in a diagonal form without unscrewing them out. (You must use the diagonal method to loosen it one by one and replace it with one after a few times, do not loosen it at one time, otherwise it is easy to deform due to uneven force.)

The direction of the screw is counterclockwise and loose; Clockwise to tight. ）

4. Use a jack to align the support point at the bottom of the car, which is generally between the two notches at the bottom beam, and the position marked by the automobile manufacturer shall prevail.

5. After the jack is aligned with the vehicle support point, it can be raised, and the tire can be easily removed when it is completely off the ground.

6. Install tires. After installing the spare tire, you can screw it on, and you also need to use a diagonal method, but it is good to screw it to the extent that it can fix the spare tire, and you don't need to tighten it completely.

7. After the body is lowered, tighten the screws and twist them with the maximum force of your hand to ensure that the tires do not fall off when driving and the spare tire is installed.

Many drivers are often at a loss when they need to change the spare tire when they have a flat tire on the road, and habitually choose to give their relatives and friends or auto repairers to seek their help. But if you do it yourself, it will only take you ten minutes.

Let's take a minute to read it carefully, and you won't have to worry about changing your tires in the future.

The right way to change your tires.

Preparation steps. When we find that the car tire is flat or we need to replace the spare tire, the first thing we need to do is to park the car in a safe place, pull over and pull the handbrake tightly.

Then find these must-have tools: spare tire, screw wrench, jack, triangle. The role of the triangle is not much to say, when changing the spare tire, put it 50-100 meters behind the car, if it is 150 meters on the highway. The rest are the tools you need to change the tire.

Step 1: Disassemble the broken tire.

First loosen the screws that fix the wheel hub on the tire, and when loosening the screws, we should take the "diagonal" principle to loosen the relative screws one by one, because this will not make the screws and wheels deformed!

To add, under normal circumstances, counterclockwise is to loosen the screws, clockwise is tightened, the screw locks are relatively tight, and you must use force to unscrew them, and the female drivers with less strength can also kick with their feet if they can't do it, but pay attention to safety.

Step 2: Use a jack.

The chassis of each car will have a jack support position, generally below the middle of the vehicle, there will be obvious marking, generally 10-15 cm away from the tire.

Note: When holding up the jack, change the spare tire to the side of the jack, remove the tires on the car and then replace them with the position where the spare tire was just placed, and then take out the tires and loosen the jack after installing the tires, and then the lock screws, which are done to prevent the jack from slipping down and causing dangerous conditions.

Step 3: Tighten the screws.

When tightening the screws, you should follow the principle of "diagonal", do not tighten all the screws as soon as you come up, and then tighten the screws after confirming that they are all finished.

Note: Tightening the screws this time is related to your own life safety, don't be soft. Always make sure the screws are tight.

After doing the above, you have already changed the tires, isn't it very simple? The spare tire can only alleviate the urgent need and cannot be used for a long time. After changing the tire, you must drive to the repair shop first to get the tire in order to avoid future troubles.

2.Take out the spare tire and tools, and use a wrench to loosen all the screws in a diagonal direction in a counterclockwise direction. Find a load-bearing beam on the site and jack it up until the tire is off the ground;

3.Remove all the screws and remove the tire, put it at the bottom of the car to prevent the jack from slipping, align the screws and install the spare tire, and install the diagonal square.

This one is very simple, 1Find the tool first and open the damaged tire screw. 2.

Use the jack to jack up the vehicle and remove the tires. 3.Replace the spare tire, and then tighten the screws.

But be sure to remember to tighten the screws diagonally, not sequentially. 4.After changing the finished tire, be sure to repair the original tire as soon as possible, and then replace the spare tire as soon as possible.

5.The speed of driving on a spare tire should not exceed 80 km/h.

First take out the jack to lift up the tire to be replaced, and then use the vehicle tool to remove the old tire, remove it and install the new one according to the method of removal.

It is not too difficult to change the spare tire of the car, and there will be a detailed operation process below to tell you how to change the spare tire. However, it should be noted that car reserved tires are generally not full-size tires, and they should be replaced as soon as possible in a car 4S shop or technical professional repair shop after being installed in the car, and they should not be driven for a few days. Unless it is a special circumstance, it must be used for a few days, and the spare tire is installed in the car, and the driving speed should not be too fast.

The process of changing car tires for reserved tires.

1. Remove the spare tire, wrench, and hydraulic jack. (The more common spare tire is placed at the bottom of the trunk of the car, and there are also some SUVs and off-road vehicles that are placed at the bottom of the car, and many are external).

2. Gradually remove the tires. Loosen all the tire screws that need to be replaced at the top angle without screwing them out. (You must choose the diagonal method to loosen it one by one and replace it with one after two times, and you don't have to loosen it at one time, otherwise it is very easy to deform due to uneven pressure.)

The angle of the screw is in the opposite direction, and the direction is loose; Clockwise for tight. ）

3. The fulcrum of the bottom end of the car is pointed to with a hydraulic jack, which is generally in the middle of the two vacancies at the chassis load-bearing beam, and the part identified by the automobile manufacturer is the standard. 4. After the hydraulic jack points to the fulcrum of the car, it can be raised, and when the tire is completely off the road, it can be easily removed from the tire.

5. Equip tires. After installing the spare tire, you can cover the screws, and you need to use the diagonal method, but it is good to screw it to a level that can fix the spare tire, and you don't need to tighten it thoroughly.

6. After the car body is lowered, tighten the screws, and tighten it with the highest force to ensure that the tires do not fall off when driving, and the spare tire is installed.

It is worth mentioning that in the case of changing reserved tires, it must be carried out under the condition of ensuring safety, and at the same time, when dismantling and replacing tires, we must pay attention to the method of tightening the screws to prevent damage to the tires. In addition, in the daily maintenance link, the spare tire can not be ignored.