How to adjust the distance between the corn harvester press and the peeling roller?

First, the quality of straw leakage or chopping is not good:

1.If the line spacing does not meet the requirements or the walking deviation is skewed, the correct operation method should be followed.

2.Check if the belt is slippery and tension the belt.

3.Check whether the blade is damaged or missing, and it should be replaced or completed in time.

4.Appropriately reduce the forward speed of the small corn harvester.

Second, the elevator does not work:

1.It is possible that the ear fell into the curved plate, and the spike should be cleaned up in time.

2.Check to see if the spikes are brought under the partition and should be reversed to remove.

3.If the transmission belt is too loose, the belt should be tensioned.

Third, the lifting chain does not work exclusion measures:

1.Check if the belt is too loose and tighten the belt.

2.There are fruit ears stuck between the stems and rollers, and they should be removed in time.

Fourth, the peeling machine is blocked:

1.Adjust the snap tight.

2.Tighten the shortage of transmission belts.

3.Adjust the high and low position of the compressor.

4.Check whether the rubber plate of the pressure feeder is aged or broken, and it should be replaced in time.

Fifth, the roller picking is blocked:

1.Slow down your drive.

2.Adjust the tool clearance appropriately.

3.Adjust the roll clearance.

4.Check if the pinch chain is working properly.

5.The elasticity of the safety spring of the ear picking tooth box is not enough, and the precompression length of the spring is appropriately compressed to improve the elastic force.

Sixth, the pinch chain is not**

1.Adjust the distance between the dial and the ground.

2.Check whether the double spindle head screw of the small corn harvester is loose and adjust the spring preload length.

3.If the pinch chain is too loose, the tension of the pinch chain should be adjusted.

4.Check whether the upper and lower sprockets of the ripper are wrapped in grass.

5.Check whether the friction plate is damaged, and if it is damaged, it should be replaced in time.

7. The chopper rotor is entangled:

1.If the belt is too loose, adjust the belt tension.

2.The distance between the blade and the ground shall not be less than 30mm

How much is the gap adjustment of corn peeling roller There are two main adjustments to be made in the work of peeling, one is the adjustment of the sieve blade, and the other is the adjustment of the inlet and outlet gate knives. The adjustment of the sieve is mainly to adjust the gap between the sieve and the peeling roller, if the gap is large, the pressure of the peeling chamber is small, and the friction of the corn is not strong, so the peeling is not clean, but the yield is high. When the inlet gate knife is opened and the outlet pressure valve is closed, the corn in the peeling chamber increases, the pressure increases, and the peeling effect is good, but the yield is low.

On the contrary, when the inlet gate knife is closed small and the discharge pressure valve is opened, there is less corn in the peeling room, the pressure is reduced, and the corn taken out is not clean and the effect is not good. According to the requirements of the internal pressure and friction of the jade loss rice peeling machine, the pressure of the peeling roller and the inlet and outlet gate knives should be adjusted according to the following methods to peel clean corn, white and black spots. (1) The gap between the corn peeling roller and the sieve should be appropriate.

The gap should not be less than the transverse diameter of the corn kernel, otherwise, the corn will be lost. The gap should not be greater than the longitudinal diameter of the corn, otherwise, the effect of taking out the corn is not good. (2) The inlet gate knife and the outlet pressure valve should be well matched.

Generally, the opening of the imported gate knife can be controlled in the whole opening of 1 2, and the zui is not more than 2 3. Some veteran operators take out the imported gate knife and let the import all be opened, which is not appropriate. Because after all opened, there is too much corn, the pressure of the peeling chamber is too great, and the rotational resistance increases, if the outlet pressure valve cannot be matched for a while, the belt will slip, and even the machine will be stuck or damaged.

The outlet pressure valve should be flexibly mastered, during operation, the gap between the peeling roller and the sieve piece should be adjusted, and then fixed, at this time, the hand only needs to operate the outlet pressure valve, and the finished corn kernel is terminated under the outlet to check the peeling effect. If the peeling is too much, you can open and reduce the pressure of the outlet pressure valve to increase the discharge; If the peeling is not good, you can increase the pressure of the pressure valve to increase the peeling effect. Until both should be taken into account to meet the requirements.

Summary. <>

<>Hello, dear, I am glad to answer for you: the corn peeling roller gap adjustment 6mm corn peeler is an indispensable mechanized farm tool for farmers. A typical corn peeler is gearbox driven, equipped with 1 or 2 pairs of longitudinally arranged rubber peeling rollers, the arrangement of the rubber rollers can be seen to be trapezoidal or 'Z' shaped (from the perspective of the axial direction of the roller).

When the corn ears pass through the rubber rollers, a group of peeling rollers rotate in opposite directions, and the corn bracts are peeled off by the friction between the peeling rollers and the corn ears. At present, the debarker of this principle is widely deployed on the corn harvester, and the debarking roller also adopts a variety of cast iron and rubber combinations.

How much is the gap between the corn peeling rollers?

<>Hello, dear, I am glad to answer for you: the corn peeling roller gap adjustment 6mm corn peeler is an indispensable mechanized farm tool for farmers. A typical corn peeler is gearbox driven, equipped with 1 or 2 pairs of longitudinally arranged rubber peeling rollers, the arrangement of the rubber rollers can be seen to be trapezoidal or 'Z' shaped (from the perspective of the axial direction of the roller).

When the corn ears pass through the rubber roller, a group of peeling rollers rotate in the opposite direction, and the corn buds are stripped off by the friction between the peeling roller and the corn ears. At present, the debarker of this principle is widely deployed on the corn harvester, and the debarking roller also adopts a variety of cast iron and rubber combinations. Celery imitation.

How not. Pro, the gap between the corn peeling rollers is adjusted by 6mm