How do you clear Konica Minolta 1580?

Konica Minolta.

1580 needs to be disassembled to clear the printer, and the specific clearing steps are as follows.

Tool Material: Konica Minolta 1580.

1. Open the front cover of the printer and plug it in and turn on the power.

2. Press and hold the "Clear" button until the interface with the words "Replace Toner Cartridge" appears.

3. Select "Yes" under "Replace Toner Cartridge" and press "Enable".

4. Continue to press and hold the "+" button until a number appears on the display.

5. Continue to press the "+" button until you see the number "11" appear on the display.

6. Then choose to press the "OK" button, and finally close the front door cover that was opened in the previous step 1, and you're good to go.

The specific operation steps for Konica Minolta 1580 to clear are as follows:

1. First of all, turn on the power of the printer and open the front cover of the printer.

2. Press and hold the "Clear" button until the "Replace Toner Cartridge" interface appears.

3. At this time, press the "Enable" button.

4. At this time, press and hold the "+" button up until a number appears.

5. Then keep pressing the "+" key until the number "11" appears.

6. This is when pressing the "OK" button and closing the front door cover, the clearing is completed and it can be printed.

Konica Minolta 1580 Zeroing requires the printer to be disassembled in order to clear it.

The specific clearing method is as follows:1. Turn on the power supply and front cover of the printer;

2. Press and hold "Clear" until the "Replace Toner Cartridge" interface appears;

3. Select "Yes" and press "Enable";

4. Press and hold the "+" button until a number appears;

5. Keep the "+" button until the number "11" appears;

6. Select the "OK" button to close the front door cover, and you're good to go.

After this kind of printer is replaced with a new toner, the printer needs to be cleared before it can be used normally, and the specific operation is as follows:

1.Turn on the power barrier and open the front cover of the printer as it is done.

2.Press and hold the "Clear" button and wait until "Replace Toner Cartridge" appears on the display interface

3.After that, press the "Enable" button once.

4.Press the "+" button above again until a number appears.

5.Keep clicking the "+" key until the number "11" appears

6.Press the "OK" button again to close the front door cover, and it will be back to normal.

Konica Minolta 185 enters maintenance mode steps such as years wide limb down:

1. First, enter the engineering mode by pressing the button;

<>3. Use the up and down keys to select the "clear data" item, and use the Qiaoyan menu settings to enter;

4. After entering the "clear data" field, select "total clear" and enter the world.

5. Select "yes", and then use the "return" button to return, and the machine can work normally.

Summary. First, power on the printer and open the front cover of the printer.

Press and hold the "Clear" button until the "Replace Toner Cartridge" interface appears.

At this point, press the "Enable" button once.

At this time, press and hold the upward "+" button until a number appears, Konica Minolta 1580MF prompts to replace the toner cartridge after adding powder, how to clean this.

First, power on the printer and open the front cover of the printer. Trillion liquid 2Press and hold the "Clear" button until the "Guess the Thing for Toner Cartridge" interface appears.

3.At this time, press a trillion to pick down the "Enable" button 4At this time, I pressed and held the "+" button up until a number appeared, after I enabled it, it always showed that the lid was opened, what happened when the front cover was closed?

It needs to be closed first.

Still no, what is displayed after getting it is to replace the toner cartridge.

Considering that it is a machine problem pro.

So what to do? Send it for repair.

Ok thanks.

You're welcome, give a thumbs up.

Hello, the number of prints on the Konica Minolta copier can be reset to zero by following these steps:1Press the copier's "Zero" or "Zero" button, which is usually located on the copier's control panel.

2.If your copier doesn't have a "Zero" or "Zero" button, you can try pressing the "Stop" button and the "Start" button until the "Zero" or "Zero" option appears on the display. 3.

If none of the above methods can clear the number of prints, you can try looking for the "Counter" or "Print History" option in the copier's menu and reset it to zero. It is important to note that zeroing out the number of prints may affect the warranty and repair records of the copier, so please proceed with caution. In addition, some copiers may not be able to zero out the number of prints, depending on the model and manufacturer of the copier.

Off-topic expansion: In addition to zeroing out the number of prints, you can also extend the life of your copier and reduce the number of repairs by:1

Clean the inside and outside of the copier regularly, especially at the inlet and outlet of the paper. 2.Use high-quality cartridges or toner and avoid low-quality cartridges or toner, which may damage the copier.

3.Avoid overusing the copier and try to print as little as possible to prolong the life of the copier. 4.

Regular maintenance and upkeep, such as replacing consumables and cleaning the inside of the machine, can reduce the number of repairs and extend the life of the copier. [Wei Li Sheng laughs] <>

Summary. 1. Restart the photocopier;

2. Check whether the plug of the photocopier is reversed and plug it back in;

3. Power on the copier, you can check whether the nozzle of the photocopier is overheated.

4. Check whether the ink cartridge of the photocopier is drying up during the ink circulation.

1. In the case of unqualified printing paper, do not spray out the ink cartridge ink.

It is necessary to improve the quality of the original printing;

2. Check whether the ink will fail in the process of cleaning the ink cartridge repeatedly.

If it does not work properly, the filter may be damaged.

3. Check whether the screws fixed by the photocopier are damaged or fall off.

4. The inside of the water box of the photocopier is a screw with a small capacity, which causes failure, and it is recommended to disassemble the inside of the water box.

5. Check whether the interface of the photocopier is loose or in poor contact.

Faults can be rectified before a suitable movement can be replaced.

Konica Minolta printer repair.

1. Restart the photocopier; 2. Check whether the plug of the photocopier is reversed and plug it back in; 3. Power on the copier, you can check whether the nozzle of the photocopier is overheated. 4. Check whether the ink cartridge of the photocopier is dry in the process of ink circulation. 1. In the case of unqualified printing paper, do not spray out the ink cartridge ink.

It is necessary to improve the quality of the original printing; 2. Check whether the ink will fail in the process of cleaning the ink cartridge repeatedly. If it does not work properly, the filter may be damaged. 3. Check whether the screws of the photocopier are damaged or fall off.

4. If the water box of the photocopier is broken down by screws with small capacity, it is recommended to disassemble the inside of the water box. 5. Check whether the interface of the photocopier is loose or in poor contact. Faults can be rectified before a suitable movement can be replaced.

Hope mine is helpful to you.

1.First, power on the printer and open the front cover of the printer.

2.Press and hold the "Clear" button until the "Replace Toner Cartridge" interface appears.

3.At this point, press the "Enable" button once.

4.At this time, press and hold the "+" key up until the number 5Then keep clicking the "+" key until the number "11" appears

6.This is done after pressing the "OK" key, closing the front door cover, and you can print.

1.Open the front cover in the power-on state and press the "Clear" button.

2.Press the "Start" button.

3.Press the "+" key until the screen shows "11" and press the "OK" key.

4.Close the front cover and you're done.

1. Turn on the power supply and front cover of the printer;

2. Press and hold "Clear" until the "Replace Toner Cartridge" interface appears;

3. Select "Yes" and press "Enable";

4. Press and hold the "+" button until a number appears;

5. Keep the "+" button until the number "11" appears;

6. Select the "OK" button to close the front door cover, and you're good to go.

This machine uses a plug-in card chip, and the chip must be replaced to clear the zero, and the machine cannot be cleared directly.