What are the key points of inventory reloading? How can it be poured?

Inverted library preparation: the vehicle is parallel to the bottom line (the front wheel is positive, you can see whether the steering wheel and the left front wheel are positive) inverted left library 1, hang the reverse gear, release the handbrake, the clutch is slowly raised to semi-linkage, stabilize the clutch after starting, adjust the speed, and reverse backwards slowly; Turn back to the right rear to observe the right rear door triangle window, when the front center bar reaches the front of the triangle window, quickly hit the direction to the right (pay attention to keep the speed of the car at the slowest speed when hitting the direction).

2. If you observe that the right rear of the car may touch the middle bar, quickly turn back to the left in a large direction, wait for a while, and it is estimated that the rear of the car will not hit the middle bar, and continue to hit the right direction.

3. After the rear of the car enters the garage smoothly, observe the left body line through the left reversing mirror and the left side line of the garage is parallel, and quickly turn the direction to the left. After the front of the car smoothly enters the warehouse (at this time, the front of the car should not touch the rods on both sides), look back at the left reversing mirror body and the side line of the flat ** condition to correct the direction, wide, to the left repair, narrow, to the right, (you can also look back at the rear window center sign and the two rear rod center sign is aligned, if the right deviation, to the left repair, left deviation, to the right repair.) Keep the direction after repairing.

There are two principles of reversing, one is easy to manage, the other is easy to use, you just need to grasp the hot goods first out of it, that is, often use or turn over quickly in the easy to out of the warehouse position, and not easy to keep in the position that is not easy to reach.

Our coaches are all asking us to play what three points and one line, I don't know if you are the same--

The steps for reloading are as follows:

1. After arriving at the parking place, shift the reverse gear, then reverse in a straight line, find the point to the right to hit the first direction and quickly hit the right full direction, whether it is a left or right reverse library, you can use this method.

2. Look at the right mirror after hitting the full direction, observe what kind of changes in the library angle and the distance between the body, when it is less than 30 cm, quickly turn the steering wheel back to continue to reverse, if the distance is greater than 30 cm, you don't need to move the direction, you can go back to half a circle directly into the warehouse.

3. Continue to reverse after returning to the right direction, look at the right rearview mirror, pay attention to the corner of the library and the front door handle, when the door handle of Jian Heng is about to enter the corner of the library, quickly continue to reverse in the direction of the full right, and then observe the left rearview mirror.

4. When the inner library angle appears, it quickly returns to the positive direction, and if you feel that the car is tilted, you can adjust it appropriately.

5. When the two sides are parallel after returning to the center, then look at the spring to grind the left rearview mirror, when the lower edge of the mirror and the edge of the library are pasted or pressed when the line can be parked, this is the step of the right library.

6, after the completion of the right inverted library to change to a gear, and then look at the left rearview mirror, when the left rear wheel center and the library angle on the same line, quickly to the left full direction out of the library, and then according to the same method into the bucket line left inverted warehouse.

The first point: the starting point:

Grasp the starting point of reversing into the warehouse is a very important step when reversing, slowly release the clutch reversing, look back at the right rear, when the middle column (black bar) of the right rear window just touches the edge of the right library, or look under the rearview mirror, about 2 fingers position, start to kill the direction.

The second point: the start of the correction point:

Repair in advance in the direction of reversing into the warehouse, observe the position of the front right handle of the door at the rear end, and start to correct when it is about to touch the corner of the warehouse, generally half a circle correction. Assuming that the direction is a circle and a half to kill, it is also called back to the straight, and the left hand and right hand start to play the direction of the pendulum.

The third point: the point where the correction is completed:

There is also a reference standard for the direction of correction, observe the front end of the front handle of the door (note that it is the front end, just the rear end) when it just enters the corner of the garage or when the extension line of the right side line of the garage is considered: 1. The right continues to die; 2. Do not kill directly back to the right (a circle direction), these two situations depend on how far the end of the body is from the right library edge line (more than 30 cm to the right to kill), less than 30 cm do not need to die, directly back to the right. Wild hail.

The fourth point: straighten the body point:

After the body is straightened, it helps to operate out of the warehouse, which depends on the left rear mirror, when the whole line of the left library just appeared, immediately return to the body.

Point 5: Parking Spots:

After warehousing, you need to find the right parking point, otherwise it is easy to press the line, some people look at the left rear mirror under just covered, some people look at the left door front handle in the middle of the bottom line of the rotten warehouse.

Attached: 30 cm of reversing into storage:

When the right rear wheel bypasses the corner of the garage into the warehouse, if the distance between the right rear wheel and the sideline is greater than 30cm, the left rear corner of the body will touch the infrared of the examination room. If you think of the three edges of the library as walls, the left rear of the car has hit the wall. Therefore, when reversing, by observing the right rearview mirror, you need to grasp the distance between the body and the corner of the garage about 30cm.

Ode to Qi Fan.

The simplest and most accurate way to reverse the warehouse: the first middle balance is adjusted to the body first, and the distance between the side car and the side car is about 1 meter. Next, start to pour the warehouse, use the right rear wheel to find the tire point in Yucong, when the tire passes the tire point in the upper right corner of the warehouse, Qing Pei Ying, immediately fill the direction.

After the body position is corrected, adjust the steering wheel, and then continue to reverse until the body is completely in storage. In the process of reversing, the head must be stretched out to the middle of the width of the car, with the eyes to the midpoint of the tail has been aligned with the midpoint of the garage bottom of the straight line, then the direction is correct, if you find that the rear of the car slowly deviates to a certain side, prove that the direction is not correct. Precautions for reversing and warehousing:

1. Adjust the seat and rearview mirror after getting into the car to ensure that the point you see is correct; 2. The speed of the car should not be too fast, the speed is too fast, the steering wheel is too late, and it is easy to press the line.

It is best to grasp the temper of the car first, that is, to always remember the essentials, the faster the steering wheel hits, the better, more hits, more hits, less hits. Always keep a clear head and practice a lot.

1. Before getting on the car, confirm that the left side of the car body is kept at a distance of meters from the sideline.

2. Get on the car, adjust the seat, start the vehicle, hang into the reverse gear, observe the small triangle glass of the right rear door from the inside of the car, when the front middle bar appears in two-thirds of the small triangle, hit the direction to the right, this is to continue to observe, when the front middle bar appears in the upper right corner of the rear windshield, stop and make a circle to the left, continue to observe the front center bar from the rear windshield to the right and disappear when the stop to the right to kill the direction. (If the current center bar is not visible in the small triangle position, but when the rear windshield has not appeared in the rear windshield, then there is no need to return to the left in a circle direction, only need to observe whether the line is parallel to the car body from the outside) continue to reverse backwards, from the left side of the car outside the observation library left side line and the left side of the car body is parallel to the left side of the car body (the distance is kept at 40 cm) stop and will be in the right direction, continue to reverse backwards, from the outside observe the left rear wheel to the corresponding point and stop.

3, one in and one out, hang into a gear, to the right to kill the direction, observe the left front wheel just pressed over the center line when parking, immediately to the left to kill the direction and observe the car body and the left side line to keep parallel to the car can be stopped, if the front of the car and the middle rod is still a distance, then should go back to the right direction, forward and stop at 5 cm from the middle bar. Engage in reverse gear, hit the direction to the right, observe the left rear wheel, stop when the left rear wheel just touches the center line, continue to reverse to the rear in the direction of the left kill, and observe that the left rear wheel is parallel to the center line when the stop (30 cm distance).

4. Two advance and two retreat, back to the right direction, hang into the first gear and walk forward for a distance, after hanging into the reverse gear, the car is reversed to the inside of the garage, and stop.

5. Diagonal out of the warehouse, hang into a gear, play a circle to the left, go to the front of the car really good between the two rods when the right is right, continue to drive forward, at this time should observe the distance between the left and right rearview mirrors and the two rods, you can turn the steering wheel to adjust. When the rearview mirror.

After two strokes, observe the left side of the tail, when the tail just out of the left front bar after parking, to the right to kill the direction, then continue to drive, when the body and the left side line parallel to the stop back to the positive direction.

6. Hang into the reverse gear, observe the left front bar and the right rear bar 80 cm behind a straight line, stop. Kill the direction to the left, reverse the car, observe the tail and the middle rod to keep at about 20 cm, pour into the warehouse (the distance is not 20 cm when the direction of the right circle continues to drive to the left when 20 cm to the left to kill the direction to continue to reverse), when the car body is parallel to the right side line when the stop, back to the right direction, out of the library is completed.

The rearview mirror leaks a corner to hit the steering wheel and adjust the distance between the body and the line.

It's good to practice more, there's nothing special about it.

It doesn't matter if it's right or left.

Dumping, the most important point is three, that is, when you reverse the library you to the right (left) to kill the steering wheel point, when the storage is almost completed, step on the brakes of the parking point and out of the library when playing the direction of the left rearview mirror along the edge of the fast near the yellow dotted line, this is the first point, (everyone's height is not the same, the point is not the same, I am close to the dotted line to die, I can call a friend to help see their own point) to the left to die, rather play early, not late, early can be corrected, although late can also be corrected, But the risk is too great (the direction must be fast, do not drag mud and water), press the clutch to reverse at a constant speed, when the left rearview mirror sees the left corner of the library do not rush, slowly pour, when the body is more than one meter away from the corner of the library to make a prediction, that is, the relationship between the body and the extension line of the library angle back to how many directions, the greater their angle, the less the direction of the return, generally the first point direction of the right back half a circle or a small half circle, adjust to keep the wheel or body and the corner of the library has a distance of 10cm, that is, after the left to die, When the left rear wheel or body into the garage and the left side line parallel to the rapid return to the positive direction, continue to fall back at a constant speed, while looking at the right side line and the right body of the distance appropriate adjustment, which side of the wide direction to which side, or which side of the narrow to the opposite direction to hit (at this time the direction to hit lightly, slowly experience).

At this time, the rear body has been completely into the garage, now to the second point, that is, the parking point, when the left rearview mirror is close to the edge of the garage mouth when the clutch brake is stepped on at the same time, (this point is not the same for each person according to the height, you can call a friend to help watch outside, the front and rear of the car is not in the garage or out of the bottom of the garage, find their own point) and then hang a gear ready to go out of the garage (we do not require the reversing into the garage does not require to play the turn signal, if you have a requirement must remember to play the turn signal), out of the garage I did not release the brakes.

Because the library in the examination room has a little backward downhill, if you don't step on the brakes to start, you have to slip, and a few of my friends hang up like this, if you guys are there Kuping is a different matter. Start out of the library at a constant speed, when the left rear wheel is seen in the left rear wheel and the edge of the library mouth is parallel, quickly hit the right to kill, this is the third point, this point is the same, keep the direction still and reach the right library back to the body, some masters teach to keep the direction still, how to go out, how to return to the library, I have not used this method, this method hangs a lot of people, a little error is powerless to return to the sky, or back to the right direction of their own correction good, the right library into the method and the left, the only difference is that the right rear mirror away from us, The relationship between the corner and the body is the same, that is, the whole body and the corner of the body become smaller, and the distance of 10cm is also correspondingly smaller. Okay, so wordy, I hope it will be helpful to everyone, the key point of subject two is the slow clutch pressure, uniform speed, point to see accurately and direction to play quickly, and finally I wish you all a smooth passage of subject two.

The body should be positive (also the premise of warehousing), the body is perpendicular to the bottom of the library, and the side of the compartment that can be seen is perpendicular to the bottom of the library; Secondly, the steering wheel should be positive, usually one and a half circles and a half bottom, and the steering wheel should be flat and flat; Secondly, try to get a little closer to the middle line, whether it will be out of the left line, then put your two eyes on the top of the car.

Reverse pile, also called inverted warehouse, inverted rod, pile test, is an assessment point in the driver's test, that is, in the movement to manipulate the vehicle from both sides of the correct reverse into the garage, mainly to examine the driver's ability to operate the car in the field and the driver's sense of space when the vehicle moves.

Reverse storage skills: gently lift the clutch to move the car back, control the speed, look at the left rearview mirror, and kill the steering wheel right when the right starting point induction line appears in the left rearview mirror.

Kill the steering wheel to the right, continue to move back, can not stop in the middle, while observing the right rearview mirror, to the rightmost line exposed, keep the body and the library angle distance 30cm, (less than 30cm back half a circle steering wheel adjustment, more than 30cm continue to kill the right direction, the body is still greater than 30cm, may be to see 1 o'clock when the steering wheel is slow, next time in advance or speed up the direction of the speed). Continue to move back, when the right rearview mirror library edge line is parallel to the body (as shown in the figure), the steering wheel is back to the center, the body is corrected, and the library is reversed into the bottom.

Look at the left rearview mirror when reversing the bottom of the warehouse, when the front edge line of the library is out of the left rearview mirror position, stop, and the reversing is completed.

The success of the reloading is not only to master the skills, but also to practice more, only by constantly practicing and mastering can the correct reloading success.