How can we pour the positive and negative warehouses, and how can we pour the warehouses well?

Reversing warehousing operation skills:

1. Control the driving speed and idle with 1 gear or reverse gear throughout the whole process, and drive at what speed you start.

2. Carefully observe the process of reversing after controlling the steering timing, grasp the key points of steering, and turn in a timely manner.

3. When controlling the driving route test, the driving route of the car mainly depends on the speed and speed of rotating the steering wheel.

1. Before getting on the car, confirm that the left side of the car body is kept at a distance of meters from the sideline.

2. Get on the car, adjust the seat, start the vehicle, hang into the reverse gear, observe the small triangle glass of the right rear door from the inside of the car, when the front middle bar appears in two-thirds of the small triangle, hit the direction to the right, this is to continue to observe, when the front middle bar appears in the upper right corner of the rear windshield, stop and make a circle to the left, continue to observe the front center bar from the rear windshield to the right and disappear when the stop to the right to kill the direction. (If the current center bar is not visible in the small triangle position, but when the rear windshield has not appeared in the rear windshield, then there is no need to return to the left in a circle direction, only need to observe whether the line is parallel to the car body from the outside) continue to reverse backwards, from the left side of the car outside the observation library left side line and the left side of the car body is parallel to the left side of the car body (the distance is kept at 40 cm) stop and will be in the right direction, continue to reverse backwards, from the outside observe the left rear wheel to the corresponding point and stop.

3, one in and one out, hang into a gear, to the right to kill the direction, observe the left front wheel just pressed over the center line when parking, immediately to the left to kill the direction and observe the car body and the left side line to keep parallel to the car can be stopped, if the front of the car and the middle rod is still a distance, then should go back to the right direction, forward and stop at 5 cm from the middle bar. Engage in reverse gear, hit the direction to the right, observe the left rear wheel, stop when the left rear wheel just touches the center line, continue to reverse to the rear in the direction of the left kill, and observe that the left rear wheel is parallel to the center line when the stop (30 cm distance).

4. Two advance and two retreat, back to the right direction, hang into the first gear and walk forward for a distance, after hanging into the reverse gear, the car is reversed to the inside of the garage, and stop.

5. Diagonal out of the warehouse, hang into a gear, play a circle to the left, go to the front of the car really good between the two rods when the right is right, continue to drive forward, at this time should observe the distance between the left and right rearview mirrors and the two rods, you can turn the steering wheel to adjust. When the rearview mirror.

After two strokes, observe the left side of the tail, when the tail just out of the left front bar after parking, to the right to kill the direction, then continue to drive, when the body and the left side line parallel to the stop back to the positive direction.

6. Hang into the reverse gear, observe the left front bar and the right rear bar 80 cm behind a straight line, stop. Kill the direction to the left, reverse the car, observe the tail and the middle rod to keep at about 20 cm, pour into the warehouse (the distance is not 20 cm when the direction of the right circle continues to drive to the left when 20 cm to the left to kill the direction to continue to reverse), when the car body is parallel to the right side line when the stop, back to the right direction, out of the library is completed.

Commonly used points, the distance between left and right is between 1.5 and 2.5 meters, and the dotted line can be aligned.

Both sides of the positive and negative library explanation method, this library is not difficult to learn!

The reversing skills of the positive and negative warehouses are as follows:

1. Take the inverted left library as an example to illustrate (the operation of the inverted right library is the same as that of the inverted left library, and the direction is opposite). Shift one gear in reverse, hit the left turn signal, move the car slowly, observe the left rearview mirror, and when the left rear wheel is out of the corner, quickly hit the left direction;

2. The front of the car is positive, the direction is quickly back to right, when the left side of the rearview mirror is 20cm away from the yellow dotted line, stop;

3. Shift the reverse gear in the first gear, and pay attention to the left rearview mirror while reversing, and when the lower edge of the rearview mirror coincides with the dotted line, quickly hit the left direction;

4. Observe the left rearview mirror, when the left side of the body is about 30cm away from the library angle, return to the right direction;

5. Observe the left rear wheel through the left rearview mirror, when the left rear wheel is on the extension line of the library, kill the direction of Henghuai to the left;

6. Observe the right rearview mirror, and when you see the corner of the warehouse, return to the right direction and slowly enter the warehouse; Pina.

7. When the lower edge of the left rearview mirror coincides with the yellow line in front, stop. At this time, the reversing and warehousing are all completed.

Precautions for reversing and warehousing:

1. Learn to adjust the seat;

2. Adjust the rearview mirror and observe the rearview mirror;

3. Adjust the distance between the body and the sideline;

4. Learn to use the method of pressing the clutch pedal to control the speed;

5. Learn to trim the direction after warehousing.

The steps for reloading are as follows:

1. After arriving at the parking place, shift the reverse gear, then reverse in a straight line, find the point to the right to hit the first direction and quickly hit the right full direction, whether it is a left or right reverse library, you can use this method.

2. Look at the right mirror after hitting the full direction, observe what kind of changes in the library angle and the distance between the body, when it is less than 30 cm, quickly turn the steering wheel back to continue to reverse, if the distance is greater than 30 cm, you don't need to move the direction, you can go back to half a circle directly into the warehouse.

3. Continue to reverse after returning to the right direction, look at the right rearview mirror, pay attention to the corner of the library and the front door handle, when the door handle of Jian Heng is about to enter the corner of the library, quickly continue to reverse in the direction of the full right, and then observe the left rearview mirror.

4. When the inner library angle appears, it quickly returns to the positive direction, and if you feel that the car is tilted, you can adjust it appropriately.

5. When the two sides are parallel after returning to the center, then look at the spring to grind the left rearview mirror, when the lower edge of the mirror and the edge of the library are pasted or pressed when the line can be parked, this is the step of the right library.

6, after the completion of the right inverted library to change to a gear, and then look at the left rearview mirror, when the left rear wheel center and the library angle on the same line, quickly to the left full direction out of the library, and then according to the same method into the bucket line left inverted warehouse.

It is best to grasp the temper of the car first, that is, to always remember the essentials, the faster the steering wheel hits, the better, more hits, more hits, less hits. Always keep a clear head and practice a lot.

The rearview mirror leaks a corner to hit the steering wheel and adjust the distance between the body and the line.

It's good to practice more, there's nothing special about it.

It's pretty much the same, as long as you practice it carefully, it's basically the same.

Key points of reversing warehousing operation:

The most basic thing in reversing is to be sure to use the clutch to control the speed, the speed is slow, and there will be opportunities to make space adjustments in the future.

After the feeling of the first clutch is controlled, the ideal speed is controlled, and it is not necessary to loosen and tighten from time to time, and it is enough to maintain this speed throughout the process. If you lift your left foot and put it down, it is easy to stop or stop when the speed is slow. Of course, the speed of the car will become slower when it is reversed, and it may feel like it can be loosened a little when it stops, but don't be too greedy, and then press the clutch to maintain the original speed after turning right.

The others are mainly the following points:

1. It is not necessary to deal with all possible situations according to the dead dogma, and the pursuit of one-step thinking is not helpful to your on-the-spot adaptability, 2. You must learn different processing methods that can be safely put into storage in various situations.

Inverted library preparation: the vehicle is parallel to the bottom line (the front wheel is positive, you can see whether the steering wheel and the left front wheel are positive) inverted left library 1, hang the reverse gear, release the handbrake, the clutch is slowly raised to semi-linkage, stabilize the clutch after starting, adjust the speed, and reverse backwards slowly; Turn back to the right rear to observe the right rear door triangle window, when the front center bar reaches the front of the triangle window, quickly hit the direction to the right (pay attention to keep the speed of the car at the slowest speed when hitting the direction).

2. If you observe that the right rear of the car may touch the middle bar, quickly turn back to the left in a large direction, wait for a while, and it is estimated that the rear of the car will not hit the middle bar, and continue to hit the right direction.

3. After the rear of the car enters the garage smoothly, observe the left body line through the left reversing mirror and the left side line of the garage is parallel, and quickly turn the direction to the left. After the front of the car smoothly enters the warehouse (at this time, the front of the car should not touch the rods on both sides), look back at the left reversing mirror body and the side line of the flat ** condition to correct the direction, wide, to the left repair, narrow, to the right, (you can also look back at the rear window center sign and the two rear rod center sign is aligned, if the right deviation, to the left repair, left deviation, to the right repair.) Keep the direction after repairing.

There are two principles of reversing, one is easy to manage, the other is easy to use, you just need to grasp the hot goods first out of it, that is, often use or turn over quickly in the easy to out of the warehouse position, and not easy to keep in the position that is not easy to reach.

Our coaches are all asking us to play what three points and one line, I don't know if you are the same--

The first point: the starting point.

Slowly release the clutch and reverse, look back at the right rear, when the middle column (black bar) of the right rear window just touches the edge line of the right library, or when you look under the rearview mirror, about 2 fingers, start to kill the direction. (Pay attention to the relationship between speed and position).

The second point: start the correction point.

Observe the position of the right front handle of the door against the rear end, and start to correct when this point is about to touch the corner of the library (about (5-15 cm)), usually half a circle correction. (Assuming that the direction is a circle and a half to kill, it is also called a straight, and the left hand and right hand start to play the direction of the pendulum).

The third point: the point where the correction is completed.

This point is hung up by many people).

Observe the front end of the front handle of the door (note that it is the front end, just the rear end) just enters the corner of the garage or when the extension line of the right side line of the garage is considered: 1. The right continues to die; 2. Do not kill directly back to the right (a circle direction), these two situations depend on how far the end of the body is from the right library edge line (more than 30 cm to the right to kill), less than 30 cm do not need to die, directly back to the right.

The fourth point: drag the body point.

This point is for the situation when the third point is full on the right, if the third case is not full on the right, you can jump directly to the fifth point).

This point depends on the left rear mirror, when the entire left library edge line has just appeared, immediately return to the body.

Fifth, the parking spot.

Some people look at the left rear mirror just to cover the bottom, and some people look at the middle of the left door front handle into the middle of the bottom line of the library, and the specific habits are just up to each person.

Note: The above five points are the same except for the first and fifth points due to the changes in the front and back of the seat, the height of the person, and the rearview mirror.

Dumping teaches you how to find the right point.

1. Method 1. When the rear of the car has been put into the garage and the front of the car has not been put into the garage, if the rear of the car is biased to the side of the sideline, the reason is that the timing of returning to the steering wheel is too early or too fast. That is, the midpoint of the rear of the car is not yet aligned with the midpoint of the bottom of the garage, and you put the steering wheel back to the center.

2. Method 2. When the rear of the car has been put into the garage and the front of the car has not been put into the garage, if the rear of the car is biased to the side of the center line, the reason is that the timing of returning to the steering wheel is too late or too slow. That is to say, when the midpoint of the rear of the car has been quietly aimed at the midpoint of the bottom of the garage, the steering wheel of your car has not yet returned to the right.