How to wire the five hole socket with a single control switch

A five-hole wiring is still very simple, the socket and the switch are independent, the socket part: the live wire is connected to L, the neutral wire is connected to N, the ground wire is connected to PE (some are three horizontal and one vertical), the ground wire is not connected, the switch part: from the socket L to the L of the switch L (some are com), L1 is connected to the light line, the zero line goes directly to the light, I hope it can help you.

The wiring method of the dual-control switch with five holes is as follows:First of all, it is necessary to understand the binding posts, under normal circumstances, there are seven binding posts on the back of the socket, which are marked with [L], [N], [E] [L11], [L12], [L21], [L22], of which [L] is connected to the live wire, [N] is connected to the neutral wire, and [E] is grounded to the wire.

Then connect the switch control socket, connect the switch to control the single control switch, and finally carry out the switch control double control switch, the switch needs to cooperate with the double control switch, and the specific operation steps are as follows:

Precautions: 1. The use of five-hole sockets with switches can be divided into three situations: switch control sockets, switch control single control switches, and switch control double control switches.

2. Pay attention to safe operation when wiring to avoid danger.

Single-open, double-control five-pin socket wiring, ready to open single-open, double-control five-pin socket, connect 2 wires on the switch jack, and connect 2 wires on the 2 wires connected to the switch jack; The specific steps are as follows:

1. Prepare a single-open, double-control five-pin socket.

2. Turn it to the back. As shown below:

3. Connect 2 wires on the switch jack.

4. Connect 2 more wires on the 2 wires connected to the switch jack.

5. Connect the switch jack in series with the socket jack. As shown below:

6. The wiring is complete.

Hello dear, thank you for waiting, let me explain to you, 1, first of all, we must figure out how the wiring terminal behind the dual-control 5-hole switch is distributed, which is generally composed of two switches, a two-hole socket hole, and a three-hole socket hole. 2. Two switch binding posts are respectively connected to the control lines of different lighting equipment, and then a live wire is drawn out from the main power line and connected to the L binding post of switch 1, and at the same time, it is extended to the L terminal post of switch 2, and then connected to the L port on the socket hole, that is, a live wire is connected to three L binding posts at the same time. 3. Then take out a neutral wire from the main power cord and connect it to the N wiring port of the socket hole.

Finally, connect the ground wire to the E terminal post on the socket, and wrap each terminal with insulating tape to protect it. We hope you are satisfied.

Single control and a five-hole socket wiring, which is actually a combination of a socket and a switch, code the two components together, and the wiring method is very simple:

1. The socket connection method is to directly connect the live wire L and the neutral wire N to the two terminals of the socket, if there are three terminals, the middle is connected to the ground wire, that is, the two-color wire we commonly use.

2. The single-control switch is simpler, the zero line does not need to be connected to the terminal, it is directly connected to the outside, and wrapped with insulating tape; The incoming line of the live wire on the terminal is connected to L1, and the outgoing line is L2, and it is so simple to complete.

How to choose a socket?

1. Observe the appearance of the socket.

First of all, carefully observe the workmanship of the product, usually the workmanship of the best products are relatively fine, there will be no flaws at each joint, there will be no variegation, and the overall color is uniform and shiny. Then check the switch of the socket, the product is very smooth when pressing the switch, the sound is crisp, there will be no jamming and friction sound, and it can bounce back smoothly after pressing it, and there will be no pause.

2. See if there is a 3C mark.

Products that have passed the relevant certification will have a certification mark, which should be checked when purchasing, otherwise it means that the product is not guaranteed and may have potential safety hazards. Also pay attention to the material used in the product, generally good quality sockets are made of copper as the socket, if you find that the socket has rust when purchasing, you should choose carefully.

The five-prong socket with dual control switch has three wiring methods.

The first method is to switch the control socket on and off the power wiring, the L2 connector of the double control switch is left blank, the L connection wire, the L1 connection to the L connector of the socket, the blue wire of the socket is the neutral wire, and the two-color wire is the ground wire, this electrician wiring method is to control the socket through the switch.

The second wiring method is to switch to control the bulb, the socket is not controlled by the switch, the blue wire is the neutral wire, and the red wire is the live wire.

The third is to connect into a double control switch lamp method, two switches to form a double control lamp, this method is often used in the room switch lamp wiring, a double control switch at the door, the head of the bed is a five-hole with a switch, the head of the bed can be charged to the mobile phone can also switch on and off the light.

Extended information: A dual-control switch is a switch with two contacts (i.e., a pair) of normally open and normally closed at the same time. Usually two dual-control switches are used to control a lamp or other electrical appliances, which means that there can be two switches to control the switch of electrical appliances such as lamps and lanterns, for example, turn on the switch when you are downstairs and turn off the switch when you are upstairs. If you want to turn off the lights, you have to run downstairs to turn them off, and you can avoid this trouble by using dual-control switches.

In addition, the dual control switch is also used to control the lamps and lanterns that need to be forcibly ignited in the emergency lighting circuit, and the two ends of the dual control switch are connected to dual power supplies, and one end is connected to the lamps, that is, a switch controls a lamp.

How to wire the dual-control switch and five-hole socket, household electricity knowledge, learn that you are also an electrician.

It's best to upload ** so that it can be clearly marked for you.

Single-open, double-control five-pin socket wiring, ready to open single-open, double-control five-pin socket, connect 2 wires on the switch jack, and connect 2 wires on the 2 wires connected to the switch jack; The specific steps are as follows:

1. Prepare a single-open, double-control five-pin socket.

2. Turn it to the back. As shown below:

3. Connect 2 wires on the switch jack.

4. Connect 2 more wires on the 2 wires connected to the switch jack.

5. Connect the switch jack in series with the socket jack. As shown below:

6. The wiring is complete.

Wiring diagram of the switch control lamp:

Switch control socket wiring diagram:

Single-control switches cannot be used as dual-control switches.

It is recommended to replace the single-control switch with a dual-control switch.

The picture above is the wiring diagram of the five-pin socket switch.

Replace the switch with your five-pin socket switch in the picture below.

How to wire the five-hole switch socket? A physical diagram of the wiring of the 5-hole switch.

A five-hole switch controls the wiring diagram of the bulb.

In the case of a switch with an outlet, the inside is already connected, and we just need to align it for the external connection. What we are talking about here is a single-control switch with a five-hole socket, the switch and the socket do not affect each other, the switch controls the bulb to connect the live wire to the switch with a five-hole socket L, and the L1 outlet wire and the neutral line are linked to the bulb at the same time. This is where the wiring of the switch is complete.

The socket part is connected below, and the live wire is connected to the L neutral wire to the ground wire at the N ground mark, and here it can be wired directly from the L of the switch to the L of the socket, which can save the wiring cost. At this point, the wiring is complete.

Note: The switch "L" in the schematic diagram corresponds to the "com" in other products, which is the same type of interface.

A five-hole switch controls the wiring diagram of the socket.

The switch with socket can also use the switch to control the socket power supply, and the wiring is as follows: the live wire enters the switch L, and then the L1 outlet wire is connected to the socket L, and the neutral wire is connected to the ground wire connected to the middle, so that the wiring method of the switch control socket is completed!

Note: The switch "L" in the schematic diagram corresponds to the "com" in other products, which is the same type of interface.

Wiring diagram of a five-hole dual-control switch.

One open five holes not only single control also has double control switch, here is introduced two a five-hole double control with one open multi-control switch to achieve three switch control a lamp, this method can be used for bedroom switch socket layout, one single double control on both sides of the bedside table with two or three pole sockets, the door is installed with a one-open multi-control switch, relative to the bedside table on both sides of the distribution installation switch and socket will save a certain cost, its specific wiring method can be accessed according to the figure. It should be noted here that the incoming line must be accessed from one open and five holes, and then connected separately!

Note: In the schematic diagram, the switch "L, L1, L2" corresponds to "COM, COM1, COM2" in other products, which are similar interfaces.

The switch needs a dual-control switch to be connected to the dual-control.

You have to buy two dual-control switches to use Remember, it must be two.