How to lay floor heating Floor heating laying method

The laying of underfloor heating requires the following steps:1Determine how the underfloor heating will be arranged:

Floor heating can be used in two ways: water heating and electric heating, water heating needs to lay pipes under the ground, and electric heating needs to lay heating cables or heating films. 2.Prepare the ground:

The ground needs to be flat, dry, dust-free, oil-free, etc., so as to facilitate the laying of floor heating. 3.Laying insulation:

Lay a layer of insulation materials on the ground, such as polystyrene foam board, extruded plastic board, etc., to reduce heat loss. 4.Laying underfloor heating pipes or electric banquet cables:

According to the design drawings, lay the floor heating pipes or cables on the insulation layer, paying attention to the spacing and arrangement between the pipes or cables. 5.Testing the underfloor heating system:

After laying the underfloor heating pipes or cables, tests are required to ensure that the underfloor heating system is functioning properly. 6.Laying of floor materials:

Laying floor materials such as floor tiles, floors, etc., on underfloor heating pipes or cables. 7.Installing the Thermostat:

Depending on the type of underfloor heating system, a thermostat is installed to control the temperature of the underfloor heating. 8.Commissioning of the underfloor heating system:

After the thermostat is installed, it needs to be commissioned to ensure that the underfloor heating system is functioning properly. The above are the steps of laying underfloor heating, it should be noted that design and planning need to be carried out before laying underfloor heating to ensure the effectiveness and safety of underfloor heating system.

Underfloor heating is a system that heats the floor through pipes or electricity** to heat the floor. Here are the five key steps and summaries for underfloor heating laying:

1.Planning and design: Before you start laying underfloor heating, you first need to plan and design your system. This includes identifying the heating area, choosing the right heating equipment and plumbing arrangement. Ensure planning and design are in line with local building codes and requirements.

2.Preparation: Before laying underfloor heating, some preparation work is required.

First, clean the slabs to ensure that the surface is flat, dry and clean. Repair any damage or defects to the floor surface if needed. Then, an insulating layer is installed to prevent heat from escaping downward.

3.Installation of plumbing or electricity**: According to the design plan, install heating pipes or electricity** on the floor.

Heating pipes can be prefabricated plastic pipes or metal pipes. The plumbing arrangement can be spiral, serpentine, or grid-shaped, depending on the design and heating needs.

4.Connecting the water and electricity supply systems: Once you have completed the installation of underfloor heating pipes or electricity**, connect them to the water supply system (if it is hot water heating) or the power supply system (if it is electric heating). Make sure the connection is tight, there are no leaks, and it is tested according to the specification requirements.

5.Completion of floor laying: After the installation of the underfloor heating system is completed, the floor can be continued. This can be floor tiles, wooden floors, carpets, or other flooring materials. Depending on the need, you can choose to install a thermal conductive layer or a chain silver chain thermal layer to improve the heating effect.

Summary: Floor heating installation requires planning and design, preparation, installation of plumbing or electricity**, connection to water and electricity supply systems, and completion of floor laying. These five steps ensure the proper installation and proper functioning of the underfloor heating system.

Throughout the process, building codes and requirements should be followed, and all connection and installation work should be ensured to meet safety standards.

Underfloor heating is a type of heating that is laid under the floor. Its laying method mainly includes the following steps:

1.Design: First of all, it is necessary to design the floor heating system, including the required heat dissipation area, heating mode, pipe direction and pipe length, etc.

2.Cleaning: The floor should be cleaned to remove dust, grease and moisture to ensure that the floor is level.

3.Laying insulation: Laying insulation to reduce energy loss. Generally, polystyrene, extruded plastic board and other materials are selected.

4.Laying a reflective film: Laying a reflective film to reflect the geothermal heat and reduce heat loss downward.

5.Installation of pipes: Installation of floor heating pipes, generally using PEX pipes or PE pipes, pipe spacing, pipe direction, pipe length and other factors should be paid attention to when laying pipes.

6.Test: Conduct a test after the installation of the pipes to confirm that there is no leakage in the floor heating pipes.

7.Covering the floor material is quietly changed: covering the ground material, generally the floor, floor tiles, etc. can be selected.

There are many factors that need to be considered when laying underfloor heating, including system design, pipeline layout, insulation materials, etc., and generally require professionals to install them.

The laying of underfloor heating needs to follow the following steps:

Clean the floor: Clean the floor of the paving area to ensure that it is smooth and free of debris.

Number of yards of separator film: Lay a layer of separator film on the ground after cleaning to isolate moisture and other pollutants on the ground.

Installation of heat dissipation pipes: According to the design drawings, install heat dissipation pipes according to the specified spacing, depth and slope requirements. Attention is also needed to ensure the heat dissipation and service life of the pipes.

Connect the pipe and control system: connect the heat dissipation pipe and the water pump, and install the floor heating control system.

Test run: After all the laying is completed, the test run is carried out to check whether there is any water leakage, water seepage or failure. If there is a problem, it needs to be fixed in time.

If you want to install floor heating at home, you need to master the specific installation method. What are the laying methods of floor heating? PChouse will take you to find out.

1. Dry paving.

In order to solve the problems of difficult construction, long construction period and difficult maintenance after the installation of the traditional wet installation method, the dry installation method came into being. Instead of using a concrete bean stone layer to fix the plumbing pipes, the dry installation of floor heating uses a special plastic formwork, which is very convenient to lay by sticking the pipes in the bulge of the formwork. The flooring is laid directly on the plastic formwork, and the hot water transfers heat to the floor through the air and the formwork, which then heats the air.

The tube is directly embedded in a special laying abrasive, no filling layer is required, the installation is simple, the heat dissipation is fast, and the installation height is generally 30-35mm, which is more expensive.

Second, wet paving.

The wet installation method is currently the most mature installation process for plumbing floor heating, and it is also relatively cheap, and it is the leading process in the domestic floor heating market. The so-called wet type refers to the use of concrete to bury the floor heating pipes, and then lay ground, tiles and other ground materials on top of the concrete layer. This layer of concrete not only protects and secures the plumbing pipes, but also serves as the main channel for heat transfer.

The concrete layer evenly distributes the heat and reduces the occurrence of localized overheating or overcooling. After laying the pipeline, cement filling is required, and the installation height is generally 70-80mm, with good heat storage and low construction cost.

1. Make a groove in the wall and prepare to install an electric floor heating thermostat in the future. Pipes are laid in the open slots, and the control lines of the electric underfloor heating pass through them.

2. Clean the site and prepare for the laying of electric floor heating.

3. Lay corner insulation boards to block the heat transmission of electric floor heating to the corners of the wall. Lay extruded plastic panels to block the heat from electric underfloor heating from dissipating to the ground. Laying reinforced aluminium foil to reflect the heat of electric underfloor heating upwards.

4. Place steel wire mesh on aluminum foil to fix the electric floor heating pipe above and increase the adhesion of concrete on the surface. Lay electric floor heating pipes on steel wire mesh and tie them firmly with plastic cable ties.

5. Thread the control line of the electric floor heating from the pre-laid line pipe, and install the temperature control panel here in the future. Use an ohmic shake meter to measure the resistivity of the paved electric underfloor heating, and if the value reaches 1500 trillion ohms, it is qualified.

6. For the installation and laying of electric floor heating, it is necessary to pay attention to the space area and layout of the room, so that the overall decoration effect of the interior is better. After the installation and use of electric floor heating, it is necessary to pay attention to regular cleaning and maintenance, so as to ensure that the electric floor heating and electric heating pipes are not blocked.

1. The heat source of the new floor heating balance comes from the air source heat pump host. The installation method requires laying floor heating pipes on the ground, by burying these pipes in the ground of the house, but after the hot water in the air source heat pump is delivered to the floor heating pipe, the hot water in the floor heating pipe can be dissipated to the tiles on the ground or the trembling floor, so that the heat radiates to the room, so that the room can achieve the purpose of heating.

2. The laying of floor heating is to complete the installation and connection of the water collector first, and then the installation of pipes and wall-hung boilers.

3. The laying method is as follows:

1.Level the ground, 2Installation of the main water pipe, 3

Laying insulation, 4Laying of reflective film, 5Laying underfloor heating pipes, 6

Install the manifold, 7Pipeline hydrostatic test, 8Backfill leveling ground, 9

Install a wall-hung boiler.

4. Among them, we need to pay attention to the strict installation of design drawings for the running of water pipes.