How to deal with water fogging in the watch, and how to deal with water mist in the watch

1. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture.

Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

2. Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will all disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch. The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Fourth, put it in a rice jar and bury it deep in the dry rice for a period of time, if it is fast, you can see the obvious effect in one night.

5. Put the watch on the TV, table or other places in the room before going to bed at night, but do not use it in an indoor area with air circulation (it is best not to open the window), because the humidity in the room will be relatively low at night, and it is easy to evaporate the water!

6. It is best to seal the watch with granular dry matter, and after a few hours, take out the watch to eliminate the stagnant water in the watch.

Seventh, the reverse is to wear it, that is, to paste the words **.

Watch maintenance and repair can refer to the service center of 702] Joy City Office Building, Xidan District, Xicheng District, Beijing to provide Swiss watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, and strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

We can use the heating method to evaporate the water vapor inside, first pull out the crown of the watch completely, and then heat the watch with an incandescent lamp, so that the watch is heated to about 520 degrees, the temperature needs to feel yourself, can not be heated too high, otherwise it will affect the inner part of the watch movement, resulting in the second damage to the watch, we use the silicone watch together, put the silicone and the watch in a closed container, the silicone has a strong water absorption performance, you can remove the watch for a long time, observe the fog problem.

The treatment methods of water mist in watches include rice cylinder drying method, silicone drying method, bulb baking method, hair dryer method, after-sales maintenance, etc.

1. Rice cylinder drying method.

The easiest way is to put the watch in a rice jar and stand still for a day, and the mist of the watch can be sucked away.

2. Silica gel drying method.

Put the watch and the silicone granular desiccant in the same airtight container, and after half a day, you can take out the watch. This benefit is that it absorbs water quickly, and the silicone desiccant can be used repeatedly without affecting the performance and accuracy of the watch, making it a good choice.

3. Bulb baking method.

Wrap the watch in toilet paper or flannel cloth with good water absorption, and bake it at a distance of four or five centimeters from the 40-watt bulb, and after half an hour, you will find that the water droplets are gone.

4. Hair dryer method.

If there is fog in the watch, you can use a hair dryer to dry it, but you should use a low-speed, mild wind to dry it slowly, otherwise it is very easy to damage the parts, and you can blow it until the moisture on the watch glass disappears.

5. After-sales maintenance.

If the above methods cannot completely remove the water, then it should be sent to a professional after-sales maintenance treatment, wipe the oil, and remove the moisture of the movement, so as to avoid oxidation and rust of the parts, which will affect the life of the watch.

The solution to the water mist on the watch is as follows:1.Wrap the table tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 3 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

2.Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

3.If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

4.If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

1. Baking: Pull the crown of the watch to the first or second gear, wrap it in a paper towel or cloth with strong water absorption, and then use a 40W incandescent bulb (it can heat up anyway), or under a strong sun, observe while baking, and the fog can be removed in about half an hour.

2. Water absorption and drying: first prepare a package of desiccant and a airtight container, and the mechanical watch is also pulled out of the crown, and then waterproof and sealed in the prepared container with the desiccant. Time is related to the amount of desiccant, and the more it is, the shorter it is.

3. If the water ingress of the mechanical watch is too serious, it needs to be sent to the watch after-sales service or maintenance center to deal with it, so as to avoid oxidation and rust of the internal movement parts of the mechanical watch, accelerate the aging of the mechanical watch, and reduce the lifespan. The above methods also work for other watches.

Notes:

1. There is fog in the watch, which means that there is moisture in the watch. In general, although the watch is hermetically sealed, there are very small pores in the joints of the case, especially in used watches.

2. Any waterproof watch should not be worn in a hot bath, sauna or in an environment with great temperature changes. Because the waterproof rubber ring is affected by temperature, it will expand and contract, voids will appear and accelerate aging, which will cause water ingress and water condensate in the surface, which will seriously damage the parts.