What s going on with my Longines mechanical watch seconds hand that walks and stops and then jumps f

The second hand of your Longines mechanical watch walks to a halt and then skips a few seconds, which can be caused by a number of reasons. Here are some possible reasons:

1.The battery is low or the battery has expired. If your Longines watch is a quartz watch, this second skip occurs when the battery is low or when the battery has expired.

In this case, it is recommended that you take your watch to a professional repair center to have a new battery replaced.

2.The movement is faulty or needs maintenance. If your Longines watch is mechanical, it may be due to a faulty internal movement or the need for maintenance. In this case, it is recommended to take the watch to an approved repair center for inspection and repair.

3.Temperature changes. Changes in temperature can affect the accuracy of your watch, and if your watch experiences a drastic temperature change, the operation of the second hand may be affected. Try to avoid exposing your watch to extreme temperatures.

4.External shocks. Any watch is a delicate mechanism, and a violent shock from the outside can cause the movement to malfunction. Please be careful to avoid collisions, falls, etc.

In conclusion, if your Longines mechanical watch has a situation where the second hand stops and then skips a few seconds, it is recommended to send the watch to a professional repair center for inspection and repair to avoid affecting the accuracy and longevity of the watch.

The three needles of the table, each with its own drive shaft.

It is a set of one, and the second hand is in the middle, which may be that the second hand and axis are loose. Just looking at the second hand is not accurate, it will not affect the accuracy of the time.

Summary. Hello, I am inquiring for you, please wait a moment and reply to you right away What is the matter with the second hand of my Longines mechanical watch that walks and stops and then jumps for a few seconds.

Hello, I am inquiring for you, please wait a moment and reply to you immediately What is the matter with the second hand of my Longines watch that walks and stops and then jumps for a few seconds.

When the quartz watch is low in power, there will be a four-second macro grip to remind the watch owner that the battery is insufficient, at this time it is necessary to replace the watch battery, if the battery is not replaced for a long time, once the battery leaks the situation, there will be corrosion of the movement, so replace the battery in time to sell!

Good! I hope mine can help you, if you are satisfied with my service, please give a thumbs up, I wish you all the best!

Just replace the battery, right?

Yes ha!

Reasons: 1. It may be a process problem.

The inner cover of the Longines mechanical watch shrank too much, pressing on the movement and causing it to stop. The solution is to open the back case, cut the inner cover, and then reinstall it again. If it can't be solved after cutting the inner cover, then it may be a core problem, just adjust the core.

2. The dust may be poor contact.

Longines mechanical watches can often be caused by improper use, and when the watch is bumped or dropped to the ground, it is likely to cause damage to the watch. When the watch is worn on the arm, the swing of the watch will cause poor contact between the battery and the battery spring clip, so it will cause the watch to stop and go. When this happens, you need to open the back case and reinstall the battery.

3. It may be a movement problem.

Longines watches will definitely wear out more or less after wearing them for a long time, and if you don't pay attention to maintenance, the failure rate of the watch will increase. If the watch is constantly bumped into hard objects, or if the watch is worn for a long time for exercise, the watch movement may malfunction. When the spindle of a Longines watch is damaged, especially when the bearing is damaged or the watch stops on the coaxial axis, it can cause the watch to stop.

Why does the second hand stop when the mechanical watch shakes, and then continue walking.

Hello! When a mechanical watch shakes, the second hand stops for a moment and then continues to walk, which is a normal phenomenon of mechanical watches, known as "jumping seconds" (also known as "jitter seconds"). This is due to the structure of the movement of a mechanical watch, and the parts inside the movement are affected by inertial forces when they are running, causing the second hand to pause before continuing to move.

This phenomenon is very common in mechanical watches, but it does not affect the normal use of the watch. However, if your robot does not have a pure watch, there are frequent beats, or the jumping seconds are too large and noisy, then you need to send your watch to a professional watch repair shop for inspection and repair. This could be a malfunction inside the movement that needs to be repaired or replaced.

I hope mine can solve your doubts, if you have any other questions, welcome to continue to consult me.

Because of the lack of power, most of them should be the amount of exercise, that is, the amount of swing arm is insufficient, fifteen to twenty times a day, it is best not to shake the winding, the shaking is different from the swing frequency, the shaking force is too large, and it is easy to shine into the movement adhesion.

Or there is a problem with the power system of the Longines watch, which needs to be returned to the manufacturer for replacement and repair. If you want to change the quartz watch, if you change the battery or don't go or the time is not accurate, it must be a problem with the movement, and you have to find Longines after-sales service if you repair it directly.

Hello, fully automatic mechanical watch, which operates by the action of the automatic winding mechanism that can tighten the mainspring by turning the rotor in any direction (visible on the transparent bottom cover table). It is conceivable that only by wearing the watch on the hand, the rotor will also rotate to generate energy as the arm moves. Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the energy of the clockwork, but it is not too absolute.

Only when worn on the celery line to constantly replenish the energy of the clockwork, the watch will not stop. Nowadays, there are people who work in the office, and the watch often stops and goes, in addition to the movement, it is because the wearer's movement is insufficient to replenish enough energy to the clockwork