What is the process of car wrapping?

Car film process, first of all, car film preparation work, cleaning and interior protection. In order to prevent the production of tiny impurities during the film, the car is usually cleaned all over the body when the car film is applied, and the car interior must be protected before the car film, especially for new cars, because it will inevitably stain the car interior during the film process, so it is necessary to prepare for the work in the early stage.

Secondly, the car film is tailored according to the size of the window. Film cutting is an important process of car film, the size of car film is generally determined according to the specific size of the window, with a size slightly larger than the size of the window.

After that, the front and rear windshields are cleaned and other window glasses. In addition to the whole vehicle cleaning, also need to carefully clean the window glass again, at the time of cleaning, generally with two kinds of scrapers (hard scraper and soft scraper) to the car repeatedly scraped. Now the car film will be operated in the dust-free workshop, which is also to prevent impurities in the car film and affect the effect of the film.

Finally, there is the film, baking film, and wet film. When cutting the film, the staff will spray soapy water on the car window glass, so that in order to better paste the car film, after the adhesive layer of the car film is uncovered, it should be carefully glued to the inside of the car window, and the edge distance between the car film and the car window should be adjusted under the lubrication of soapy water to ensure the overall appearance.

Clean the outside of the glass, make patterns and cut the film, shape and trim, clean the inside of the glass, apply the film, and check whether there are bubble creases!

What do you mean by this? The film is divided into front gears, and there are four doors and windows in the back gears! A little bit of a difference!

The front and rear gears are measured first, and the four doors and windows are modeled! Then they are all rough cut first, and then put the glass on the baking film, because the glass has a curve, so it needs to be baked! Then fine-cut, then wash the glass!

Then the upper membrane ......Probably so, but you still have to find a place to experience it.

Before applying the film, first of all, it is necessary to ensure that the working environment meets the requirements of dryness and less dust, otherwise dust and debris will enter during work, which will affect the effect of the film. It is recommended to wash the car before applying the film.

Cover the necessary areas of the vehicle, protect the interior and exterior with a protective cover, and if there is no special material, you can also choose plastic wrap. Clean the car glass that needs to be filmed, pay attention to the top and edge of the glass, and then dry it. The next step is to cut the car film, pay attention to the size of the car film to match the glass.

Spray a little water on the surface of the glass, then adsorb a certain thickness of plastic film to the window, and then draw a pattern according to the edges, the template can be a little more than the glass.

When applying film to the front and rear windshields, it is also necessary to bake and shape the film. Cover the cut car film on the outside of the glass, and then use the heat gun to shape it, this step is also more critical, and it is easy to make mistakes, because the temperature and shaping techniques of the heat gun have relatively high requirements, otherwise improper use is very good to cause the car film to be blackened or the glass is broken.

Car inspection, mainly to see if there are scratches and damages; Do a good job of protecting the car; Measure the size of the glass and preliminarily cut the automotive film; Side window cleaningThe cleaning of side window glass is divided into internal and external sides; Next is the internal film, which sprays the window film installation fluid evenly on site. After the film is applied to stabilize each piece of window film in its final position, the installation fluid should be sprayed again on the surface of the window film to lubricate the surface of the squeezed water.

How to operate the car side window film.

Step 1: A good start to the preparation is half the battle, although it is a bit ridiculous, but the preparation in advance must be in place. For car film technicians, whether it is window film or other parts, these preparations are essential.

Includes: Car inspection. Mainly to see if there are scratches, damage or something, if there is a need to communicate with the customer in time to confirm, otherwise it is difficult to talk about things after putting it in the car film.

Car washing. Generally, it is a simple cleaning of the whole vehicle, and the main purpose is dust reduction and dust removal.

Prepare materials and tools. Car film is a technical job, which will involve a lot of professional tools, such as: car film, baking gun, utility knife, gasket, large water scraper, heavy scraping, soft scraping, cleaning sponge, baking film scraper, ......Wait. Of course, car film is also required, this is a later story!

Step 2: Car protection In the process of car filming, the protection of the car is very important, basically except for the window, other parts must be firmly protected. The reason and significance of protection is to avoid problems such as cleaning solvents staining the interior or infiltrating into the car's electronic control system during the process of laminating the side windows of the car.

In particular, if the electronic control system is not properly protected and moisture penetrates, it is very likely to lead to switch failure and local short circuit. Therefore, before applying film to the side windows of the car, it is very important to carefully protect the exposed hidden electric control switch and speaker of the vehicle.

The operation mode of automobile protection: generally use protective paper, protective film, protective cover, and thicker Hengtong towels to cover the instrument panel, door trim panels, interior seats, steering wheel and rear cover plates, and do a good job of proper protection; In addition, the exterior of the body needs to be properly protected so as not to scratch the paintwork.

Step 3: Rough Cutting FilmThe factory shape of the automobile film on the market is a roll, so after getting the film, first of all, it is preliminarily cut, or the stove is called "rough cutting". Of course, before cutting, you need to measure the size of the glass, and at the same time, the rough cutting size of the car film should follow the following principles:

Side window top film size》Original side window glass edge size +5cm; The size of the left and right sides of the side window is the edge size of the original car glass +1cm; Leave a margin of 1 2cm at the bottom of the side window when cutting the film.

Step 4: Side window cleaningThe cleaning of the side window glass is divided into the inside and outside, and the inner side is the cleaning of the side glass sealing strip; The outside is the cleaning of the outside of the side glass.

1. There are two types of side window glass sealing strips for cleaning window and door glass sealing strips: glue edge and raw edge, and different cleaning methods are used for different types of seals.

If it is a rubber edge, the cleaning method is as follows: 1. Use a blowing air to blow out the sand and debris hidden in the sealing tank; 2. Spray an appropriate amount of water into the sealing groove, and directly clean the inner groove with a straight-handled plastic scraper.

Car film, methods and steps, don't mention it yourself, this is all done by professional people, we really can't do it well.