Can I use a plug in a water heater? Is the water heater socket the same size as a regular socket?

Yes, use a high-power socket.

That's it. The high-power socket is specially designed for high-power household appliances to be manufactured and used, and meets the configuration of 16 amperes (power 4000 watts), which can fully meet the bearing requirements of high-power electrical appliances.

For example, a 2 hp (heating area of 20-22 square meters) air conditioner power is about 1800 watts, the power of general household electric heaters is about 1000 watts, as well as TVs, refrigerators, etc., and general plugs.

The power is 2500W, therefore, high-power electrical appliances must be equipped with high-power sockets.

It is best not to use a fork, the high-power water heater is best to use a special line, the power is not too big and you don't need a 16A plug, if your water heater is a water storage type, I estimate that the maximum is 2 kilowatts, in fact, the ordinary socket is enough, the 16A plug is dedicated to air conditioning, go buy a replacement on it.

Wire, 16A socket, 18A air open is OK, high-power electrical appliances should be supplied separately, separate air open control.

It is best to separate high-power electrical appliances, otherwise it will cause a short circuit and burn out.

Now the use of gas water heaters has been very common, the technology is also very mature, hot water plug and play, it is very convenient to use, there is no need to leave the electric water heater socket, in fact, when you want to use it in the future, you may not be able to hang the position, so don't stay. However, many apartments have a long distance between the kitchen and bathroom, so when choosing a water heater, try to choose a large capacity, according to the different types of apartments and distances, the capacity should not be too small, and the use of hot water is not enough. When choosing a water heater, most users like to write about gas water heaters, one is more practical, and the other is low-cost.

Three styles are more beautiful. But when choosing, it's best not to throw away the electric water heater completely. It is wise to reserve an outlet for your electric water heater when renovating.

Although nowadays gas water heaters look much better than electric water heaters. Technology is evolving, and another water heater may appear later. Or a new type of electric water heater.

It seems to be a number better than a gas water heater. For example, a new type of air energy water heater, 60L, has appeared, which is similar in appearance to an electric water heater when installed, but the cost of use is much lower than that of electric water heaters and gas water heaters. So for now, gas water heaters are the best at the moment, but they can also be replaced by new ones.

So it's important to prepare in advance when we're decorating. To be sure, today's equipment is inseparable from electricity, so book the power supply in advance.

In the circuit, if conditions permit, it is best to set up an independent circuit; If the conditions do not allow, it is better to choose a circuit with fewer sockets to reserve. At least 4 square meters of wires should be reserved to basically meet the normal use of electric water heaters. You can install a five-prong socket first.

As a daily preparation, household gas water heaters and electric water heater sockets do not need to be reserved, but there must be several more sockets in the bathroom. The bathroom may not seem like a big one, and it's not the focus of home renovation, but the convenience of using the bathroom is directly related to the quality of life of your family in the future. You need to reserve an outlet under the washstand, and you can't use that kind of water heater at home.

The first water to drain is cold water, and there will be a socket left under the washbasin so that a water purifier, i.e. a heater, can be added later.

There should be an outlet for small household appliances such as hair dryers on the washstand. Reserve an outlet next to the toilet to prepare for the use of the smart toilet later. The shower room has an outlet for electric heating and electric towel rails in the future.

Now that we have entered the era of smart homes, how many sockets have been booked should have been measured on site in advance. Don't wait until the renovation is done. The whole family is real-to-do.

The small bathroom is the best place for a family's quality of life. Pay more attention when decorating a new house.

With a gas water heater at home, I don't think it's necessary to leave an outlet for installing an electric water heater in the bathroom.

Now the use of gas water heaters has been very common, the technology is also very mature, hot water is also plug and play, it is very convenient to use, there is no need to leave the socket of the electric water heater, even if it is left, there may not be a place to hang when you want to use it in the future, so don't stay. However, due to the fact that the kitchen and bathroom of many houses are far away, it is necessary to choose a large capacity when choosing a water heater, according to the house type and distance, do not choose a capacity that is too small, and the capacity is too small to use hot water is not enough.

There is a gas water heater at home, do not reserve the socket of the electric water heater in the bathroom decoration, there is no need, if the water heater is broken and needs to be replaced, you also buy a gas water heater.

Personally, I feel that it is okay to reserve one, just in case, after all, it does not affect the operation if it is left there, and it is convenient to use it when you want to use it in the future.

It is also possible to reserve a water heater power socket, so that you don't have to refer to it if you plan to install an electric water heater in the future.

It is recommended to purchase and install a three-pin socket with 16A, which is more convenient and practical to control the socket by switch.

I think even if you install a gas water heater, you should leave the socket to install the electric water heater because you don't know when it will be able to use it, and it doesn't take up space, and it doesn't affect the aesthetics when you put it there.

It is also necessary to prepare an electric water heater socket, for example, if you can prepare it with both hands, if you can't install a gas water heater, then it is also very convenient to use an electric water heater.

When you are ready to use a gas water heater, you must make a reservation for power outlets, so that it can be used conveniently.

There is a problem here with a different installation location. Electric water heaters are generally used in bathrooms, and electrical outlets are generally installed in bathrooms. Whereas, gas water heaters are used in the kitchen and are generally installed in the kitchen or adjacent to the kitchen in a well-ventilated place.

So it's generally designed separately and not together. If the bathroom and kitchen are close to each other, and the length of the power cord of the electric water heater is sufficient, you can consider installing two sockets together. FYI.

Because gas water heaters also need power to make the water heater work, it is necessary to install sockets when installing gas water heaters.

The so-called, be prepared, ready to install a gas water heater, of course, to install an electric water heater socket, if you want to install it again in the future, it will be very troublesome, anyway, it is not in the way, just one more socket.

Today's gas water heaters are basically strong exhaust water heaters, and strong exhaust gas water heaters are to use 220V alternating current, if you switch to gas water heaters, the socket of the original electric water heater is just used.

Since you are ready to use a gas water heater, you must adapt the water network, gas circuit, and power supply in advance! So as not to bury yourself in hidden dangers and troubles in the future!

In general, the size of the water heater socket is not the same as that of the ordinary socket.

Single-phase 3 kilowatt electric water heater, the rated current can reach 14A, the minimum should be 16A socket, if the socket size is appropriate, it is best to use a 25A socket. When the high-power water heater used in the socket first starts working, it will cause the instability of the power supply voltage. Socket specifications with switch are very common, such as three-hole with switch, five-hole with switch, 16A air conditioner, etc. with switch socket.

The switch is generally used to control whether the socket is energized or not. Sockets with switches are generally installed within reach, and outlets with switches do not need to be installed in places that are not within reach. Frequent plugging and unplugging has certain damage to electrical appliances, and the use of sockets with switches can save every unplugging and unplugging, which is a kind of protection for electrical appliances, especially some high-power electrical appliances are best not to be plugged and unplugged frequently;

A waterproof cover can be installed on the wall socket for the electrical outlet.

The socket can be wrapped directly in a plastic bag or plastic wrap.