How to refill Canon MG2580 printer cartridges

I use this printer, I usually do.

Open the lower cover, and the cartridge will automatically move to the middle.

Just unplug the power supply and take the cartridge out.

Add ink with a syringe, about 8ml at a time.

Attach it and close the lid when you are done.

Turn on the power, at this time you may not be able to print, so you have to clear it, method: press and hold the stop button for more than 10 seconds, you can continue to print under normal circumstances, the prompt says that the ink is not enough, it doesn't matter, just continue printing.

The original cartridge can generally print about 180 sheets, remember the point, and add ink when it is almost done. I'm a newbie, so I know so much, good luck!

Label tear off. Find the tiny hole in the middle, about the size of a pinpoint.

It is the same as sending the twist.

Drill bit. Rotate clockwise until you don't add too much ink.

Add about 7-8ml

Let it sit for a while.

This method is suitable for:

People who use small amounts.

It is recommended to change the supply with more use.

How much ink was used.

Directly from the outside.

Ink jar can see.

This. Directly inked.

How much is printed.

You have to add ink. It's a matter of experience.

And even if you make an offering.

The outer ink bottle is out of ink.

Just add it directly. It's intuitive.

So so. This Canon sputtering nozzle.

The lifespan is probably only.

About 5,000 sheets.

Unlike the epson piezoelectric type, it has a long life.

PS recommends that you change the supply.

There are a lot of treasures.

There are tutorials. I really don't know.

You can go to the place where you bought the machine.

Probably. Around 150.

Ink to buy Tianwei's kind with anti-counterfeiting.

8 pieces of each color.

The specific steps for adding ink to Canon MG2580S printer 845 and 846 cartridges are:

1. Take out the "ink cartridge" of the printer, color printers have two cartridges: "color cartridge" and "black cartridge", while "black and white printer" only has one kind of "black ink cartridge".

Second, then gently tear off the "label" on the cartridge, and be careful not to break the label.

3. After tearing off the "label", distinguish the "blue inking hole", "yellow inking hole" and "red inking hole".

Fourth, then use a syringe to extract the "ink" that needs to be added.

Fifth, the version of different colors of "ink" according to different "ink hole rights" to inject ink.

6. After the ink installation is completed, paste the "label" back to the original place and cover the "ink hole" to complete the operation.

How to reset your Canon printer:

<>4. Then use the left and right arrow buttons to select RestoreDefaults, and then press Menu Enter twice, as shown in the image.

Summary. Can you use this printer before adding ink? If it can be used normally, it is the cause of adding ink.

Can you use this printer before adding ink? If it can be used normally, it is the cause of adding ink.

Can be used before adding ink.

There are two specific situations: (1) Check which hole of the ink matches the body, if it does not match, it is impossible to identify the ink for printing. (2) The installation position of the ink cartridge is incorrect, resulting in the machine being unable to recognize, and in this case, there is no Li elimination method printing.

What should I do?

The first way is to shut down and restart, turn off the printer and restart it 10 minutes later. The second way is to take out the cartridge and refill it.

I've tried them all. No way.

These methods are commonly used by us, if these methods can not be solved, then only find professional maintenance personnel!

Open the lower lid, and the box will automatically move to the middle. Unplug the power directly, take out the cartridge, and add ink with a syringe, adding about 8ml at a time. Install it after adding, close the lid, turn on the power, and it may not be printed at this time, so it is necessary to clear it, method:

Press and hold the stop button for more than 10 seconds, you can continue to print under normal circumstances, and it doesn't matter if the prompt says that the ink is insufficient, just continue printing.

Take out the Wu Meng cartridge.

When taking the cartridge, prepare a clean piece of paper and place the cartridge on it.

A piece of adhesive tape is attached to the top of each ink cartridge, and there is usually a hole under the adhesive tape to inject ink. Just tear it gently open and you can see it.

The purchased ink generally has a more convenient tip for adding ink, and be careful to add ink once squeezed into too much. Because bubbles will be generated. In this way, you can add it gradually. After adding ink, it is recommended to seal the hole with tape. This prevents ink from spilling and dust from drifting in.

Summary. 1. The Canon MG2580 printer flashes two yellow lights, which is a warning that the surface printer is malfunctioning. The faults may be as follows:

2. There is no paper on the tray, and the solution at this time is to press and hold the stop button for 5 seconds to stop the flashing phenomenon.

3. The ink cartridge is faulty, and the ink cartridge cannot be recognized. If the cartridge is not recognized, you should remove the cover of the copy window, then let the cartridge stay in the middle and unplug the power cord. Take out the ink cartridge, hit the contacts of the ink cartridge with pure water, and then use a hair dryer to dry the contacts of the ink cartridge, turn on the machine after it is installed in place, and eliminate the fault immediately.

How to reset the Canon printer MG2580 cartridge after refilling.

Hello noisy, I'm glad to be able to answer your questions for you, please wait two minutes, Brother Shenghui, I see your question here, and I'm going to inquire about the relevant information for you, the teacher also needs time to type, please be patient and wait for two minutes! Please don't end the consultation |! <

<>Thank you very much for waiting, I put your question on the back for you;; One is that the domestic ink is not recognized, and the ink can be identified by pressing the reset button for five seconds, and the second is that the ink is not good for adding hail and the ink is bad, and the ink can not be added too much, just a small grid is OK, and the third is that it cannot be printed The ink inside the ink cartridge is a blind sponge, and the ink added is not evenly sourced into the nozzle Take the ink cartridge and gently tap it to let the ink penetrate evenly Fourth, **Canon machine was designed by unscrupulous manufacturers to modify the ink cartridge chip cannot be used to add ink Can only be used back to the original ink.

Canon MG2580S yellow and green lights flash and cannot be used normally.

Why. 1. The Canon MG2580 printer flashes two yellow lights, which is a warning that the surface printer is malfunctioning. The faults may be as follows:

2. There is no paper on the tray, and the solution at this time is to press and hold the stop button for 5 seconds to stop the flashing phenomenon. 3. If the cartridge is faulty, the cartridge macro can not be recognized. If the cartridge is not recognized, you should unplug the power cord by removing the lid key source plate of the copy window, then let the cartridge stay in the middle and slide it to the middle.

Take out the ink cartridge, hit the contacts of the ink cartridge with pure water, and then use a hair dryer to dry the contacts of the ink cartridge, and after installing it in place, the draft will be turned on in a stateless state, and the fault will be eliminated immediately.

Summary. 1.Turn on the printer first, 2

Then press the menu enter key, 3Then button to select Service, then press Menu Enter, 4Then use the left and right arrow buttons to select RestoreDefaults, then press Menu Enter twice, 5

When you finally return to the ready state, the restore setup is complete.

Hello, we have received your question and are working hard to prepare the answer for you, and will reply to you within five minutes! Wait a moment! ^

1.Turn on the printer first, 2Then press the menu enter key, 3

Then button to select Service, then press Menu Enter, 4Then make Jian Shizao use the left and right directional buttons to select RestoreDefaults, and then press Menu Enter twice, 5When it is finally restored to the ready state, the settings will be restored and the block will be restored.

I'm glad to answer for you, your question has been solved If you have any questions, you can continue to ask, if not, I hope you can give a thumbs up, thank you, I wish you a healthy and happy family.

HP LaserJetM1005 Monochrome All-in-One Laser Reset to factory settings.

The steps are as follows: 1. Turn on the power of the printer and turn on the printer, as shown in the figure below.

2. In the control panel of the printer device.

, press the Menu Enter key, as shown in the image below.

3. Then use the left and right directional buttons to select "Settings".

4. Use the left and right directional buttons to select the "Settings" option, and then press Menu Enter twice, as shown in the figure below.

5. Wait until the all-in-one machine is restored to the ready state (the LCD screen shows ready), and the reset will be completed, as shown in the figure below.