How to overclock the E5200 and how to overclock the Xeon E5620?

First of all, you play games, super CPU does not have much improvement on the game, my CPUE7400 has been super to 4G, graphics card Sotai GTS250, super 4G and not super, playing Crysis, there is not much difference, if you really want to play games to go super u also if the next software super graphics card (there are many software super graphics cards online, each has its own merits), super graphics card is much simpler than super u. Step by step 1m 1m a little bit of super, as long as you can pass or15 minutes, it's OK to run 3d06.

Since your question is going to be super U, of course I can't go off topic.

Overclocking is a very complicated one, not simply changing the external frequency, adding some voltage, 1, your U's physique, many ashes overclocking players go to buy a fixed batch number of U, such as overclocking cost-effective E5200, players like to use 5 capacitors (it's best if you see how many capacitors your u is, if five envy me, hehe). 2. Power supply. 3. Memory constitution.

4 motherboards. 5. Heat dissipation.

1、First of all, we must solve the problem of CPU and North Bridge heat dissipation,If you use the original CPU fan,Don't overceed,It will be very miserable,100 yuan or less recommended——Kyushu Fengshen Alpha 400 Plus——Overclocking three Red Sea HP-9——If it is "not bad money", it is recommended that Kyushu Fengshen Black Killer Whale Gold or Ice Blade, I am using Black Killer Whale Gold, E7400 Super 4G or baking machine for 3 hours, up to 68 degrees, and can take care of North Bridge heat dissipation.

2. There is no problem with the surface of the E series CPU below 75 degrees, pay attention to the temperature of the north bridge during the overclocking process, the temperature of the north bridge is too high, and it will also cause a direct crash. It can be detected with everest.

2. Memory physique, set the memory frequency and CPU to 1:1, that is to say, when you exceed the CPU, the memory will also go up, if the memory physique is not good, it will also lead to a crash. Recommended memory non-connectivity, 8:

10 or 9:10, or simply lock with the original frequency.

3. Lock PCI and PCI-E frequencies, reference values 99-105.

4, super thunder for too many reasons, the following take 4G as an example, directly change the CPU external frequency to 320, if your motherboard can support changing the frequency doubling, the frequency doubling will be reduced, become 12, so that your external frequency needs to be changed to 333, to the memory non-connection, 8:10 or 9:10 or simply use the original frequency, memory timing 5 5 5 15 2T, if it is still not operating normally, it is recommended to give the north bridge + or voltage, pay attention to check the temperature of the north bridge, more than 75 degrees is not a big deal, as long as it does not crash, It is not recommended to add voltage to the CPU, if your motherboard supports it, you can properly add voltage to the vid and VTT of the CPU, and the voltage of the E series CPU is under control, no problem.

Evaluate whether the overclocking is successful, run OR (CPU oven software) for more than 1 hour, 3D06 runs normally, the maximum temperature of the CPU oven is controlled below 70 degrees, and the maximum temperature of the North Bridge is controlled below 75 degrees. It's a success, Xiao Chao is pleasant, big is super hurtful, just enough, step by step, I hope the above can solve your problem.

Overclocking! Not recommended for newbies! To prepare, 1 chassis CPU fan must have a good heat sink!

In case the temperature is too high after CPU overclocking 2 Familiar with the BIOS settings, should be overclocked to set it here, don't do it if you don't understand, do not do it well, clean up the BIOS before it can be restored and booted, 3 Prepare the CPU test software after successful overclocking.

I just saw one who said he was noisy.

Overclocking with software has been a technique for a long time!

Or setting up the BIOS is king! With the motherboard manual, properly adjust the external frequency, which is the most entry-level overclocking. Overclocking in detail requires a lot of technology, go to the CPU forum in Zhongguancun to see the overclocking technology post!

Overclocking has high requirements for the motherboard, power supply, and heat dissipation, and may damage the hardware, so it is recommended to know more before starting!

Overclocking is risky, so use caution.

The specific way to overclock is to press del when you boot up

Go to the BIOS menu

Then select the CPU

clockrate option, modify and enable this option. (enabled is enabled, disabled is disabled).

Just pull the external frequency to 240MHz directly in the BIOS, and don't change anything else. If not, lock the PCI bus frequency to 100, reduce the ratio of memory to CPU external frequency to or 1:1, and pull the external frequency to 266

Generally speaking, 3G is easy. My E2200 can go on 3G, let alone E5200Good luck.

e5200 external frequency 200, the frequency doubling is, so it is 200*, the general overclocking is the frequency doubling keep, and then increase the external frequency, for example, the external frequency to 333 is 333*. After the external frequency increases, the voltage of the CPU can be added if the machine cannot be turned on, which can generally reach the E5200 of the capacitor. When overclocking, the out-of-frequency ratio of memory can be maintained at 1:

1.The other is to increase the frequency doubling and reduce the external frequency, for example, I overtook the e5200 to 380*.

In short, you need to keep trying various parameters, and it is best to take a pen to record the various permutations and combinations you have tried.

5 capacitors are basic, and 4G is passing.

Mine is also 5 capacitors, 4G can only go through 30 minutes of OR (memory instability), and finally stabilized.

1.Intel Xeon E5620, 4 cores and 8 threads, clock speed, turbo up to the first generation Core i7 920, Core i7 950, etc., use the same architecture.

2.The main frequency of the E5620 itself is relatively low (because it is set very conservatively to ensure stable operation for a long time in order to be used on the server, but based on the excellent constitution of Xeon, it is very easy to overclock the E5620).

3.Turn off the Turbo Mode in the BIOS (Disableable), directly adjust the external frequency to, the frequency doubling X19 (non-adjustable), the core voltage is the default, no need to adjust, so that you can easily overclock the E5620 to, run completely stress-free, no need to replace the fan, the operating temperature almost unchanged, very stable. After overclocking, the E5620 can basically reach the level of the Core i7 970.

4.You can even try to adjust the external frequency to 220MHz, at this time you can overshoot the E5620, and there is no need to replace the fan, the operating temperature is a little higher (more than 65 degrees), but the operation is still very stable.