How to set up Tengda N318 connection fiber

The router is set up as follows: 1. Line connection: a

There is an adsl modem cat) to connect the network cable out of the cat to the router (WAN port), and then connect the network cable of the computer to the router (any port numbered 1 2 3 4) BConnect the broadband cable to the router (WAN port), and then connect the network cable of the computer to the router (any port numbered 1 2 3 4) Second, log in to the router interface. In your browser, type:

Press Enter, enter the pop-up page: admin and click "OK". 3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: it is generally divided into three types as follows: ADSL dialing:

Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet access method, Internet access and Internet password correctly enter the broadband and password, you can. Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet, you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP mode", and enter the fixed IP address, subnet mask, gateway, DNS domain name server and other parameters of the Internet into the correct one. 4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the corresponding connection mode is displayed correctly.

1.Open your computer browser and log in.

2.Click "Internet Settings", "Wireless Password", you can set 8 or more, numeric or alphanumeric password, and click OK after changing.

Step 1: Type in the browser: press enter, as shown below

Note:1To change the wireless password, it is strongly recommended to change the wireless network name as well;

2.After you change the wireless network name or wireless password, the wireless connection will be disconnected and you need to scan the connection again.

Isn't there an instruction manual? You can enter or.

Hello! Here's how to set up a wireless router:

1. Enter the router address, connect the wireless router, enter the address you see on the router in the browser, generally of course, if your home is using ** online network, then you need to prepare an additional modem, commonly known as "cat").

2. Enter the corresponding account password, and after entering, you will see that you have entered the corresponding account and password.

3. Select the Setup Wizard, and then enter the operation interface, you will see a Setup Wizard on the left, and enter (generally pop up automatically).

4. Enter the Internet mode setting and set the interface of the wizard.

5. Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed.

6. Enter the account password, select PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, there will be an account number to open broadband, fill it in OK.

7. Set the password of the router, and then enter the wireless settings after the next step, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill it in casually, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

8. The next step is to set it up successfully.

9. Click Done, the router will automatically restart, at this time you should wait patiently. The interface that appears after success.

10. How to connect the mobile phone to wifi is simpler, when your router is set up, click the menu key of the mobile phone, and then enter the mobile phone settings, the first item is wifi, and then you set it to on, click to enter the wifi list, and select the wireless network name set in your previous router. Enter the password you set earlier to connect.

Summary: How to use a wireless router, is a more common problem, but also a relatively simple problem, I believe that as long as you have an experience, you can also become a god, of course, the router settings are far from these simple content, there are more setting options after logging in to the router settings page, set other options, such as binding MAC address, over IP, firewall settings, etc., can make your wireless network more secure, to prevent being rubbed off the network.

A: Wireless relay is to realize the amplification effect of wireless, which can avoid the trouble of wired connection, which is convenient and beautiful.

In the following cases, you can consider setting up a wireless trunk:

If you already have a router and need to use another router for secondary routing, you don't want to connect it through a network cable.

Due to the demand of WiFi usage range, the wireless signal needs to be amplified.

Setup steps:

Select the "Hotspot Signal Amplification" mode, and the wireless signal name of the unit will not change after setting;

Or select the "Universal Trunk" mode, and set the wireless signal name of the machine to the higher-level signal name.

Step 3: Click "OK" and wait for the router to restart.

Step 4: On the redirected page, click "Wireless Relay" to check whether the networking status is "Relay Successful!" ”

How to set up a wireless relay on a wireless router:

The first wireless router:

1.First, log in to the router that is connected to the Broadband Modem.

2.Set the SSID number and Channel in Wireless Settings - Basic Settings, and set the fixed channel number.

3.Set the wireless signal encryption information in the Wireless Settings - Wireless Security Settings to record the SSID, channel, and encryption settings of the wireless router after setting.

Second Wireless Router:

1.Log in to the second wireless router that needs to be bridged.

2.In the network parameters - LAN port setting, change the IP address to be different from the first router (to prevent IP address conflicts), for example, save, the router will automatically restart.

4.Select the SSID number of the first router in the list of scanned signals and click "Connect".

5.Set the channel to be the same as the first router channel. At the same time, set the encryption information to be the same as the first router, and click "Save".

6.Shut down the DHCP server. In the DHCP server, select Disable, save, and restart the router.

7.At this point, the first wireless router and the second wireless router have successfully established WDS.