Audemars Piguet watch stops, Audemars Piguet watches stop and go, what are the reasons for stopping

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

Hello, it is possible that the watch is magnetized or the power is insufficient. If you need to wind a mechanical watch by hand.

Generally, the normal winding takes 30 times, and it is basically full, (provided that you want to be full) The winding watch on your hand actually doesn't matter, as long as you keep it up until you can't turn it, the mainspring is full.

For automatic watches, because most automatic watches can be wound by hand, especially when worn for the first time or after stopping, you need to start the winding with your hand first. (It is recommended that you do not rely on the rotor to wind the full string at the beginning) everyone also knows that because the automatic watch is "not up to the string", it is recommended that the number of winding times of the automatic watch should be more than less, and you may wish to put a few more, such as up to 40 times, it is basically guaranteed to be full.

Audemars Piguet watches are repaired in Room 707, 7th Floor, Block 1, Grand Gateway Center, No. 1 Hongqiao Road, Xuhui District, Shanghai.

1.Insufficient power: mechanical watches are divided into manual mechanical watches and automatic mechanical watches, insufficient power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of movement, and it can be directly manually wound to supplement the power.

2.No maintenance: mechanical watches are generally maintained once every 2 to 3 years, the watch is used for a long time, the lubricating oil in the movement will dry up, and the friction of each gear for a long time will produce iron filings, increase the friction between the gears, this kind of problem only needs to clean the movement, re-refueling.

3.Shock: A mechanical watch has a complex structure and is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop.

According to the reason why the watch is slow, you can take corresponding measures, pay attention to the winding of the manual machinery, maintain the normal amount of exercise of the automatic mechanical arm, maintain it on time, pay attention to the watch waterproof, shockproof and anti-magnetic, and send it for repair in time if there is a problem.

4.Hairspring failure, hairspring failure is also one of the reasons for the mechanical watch steal stop, the above mentioned lack of power caused by steal stop, on the contrary, if the amount of exercise is too large, the clockwork is relatively tight and causes the failure of the upper bar mechanism, it will also cause insufficient power, this situation generally occurs at about 9 o'clock to 12 o'clock in the evening, at this time, the watch with calendar function turns the roulette wheel, which will lead to insufficient power calendar jam to stop the watch. This kind of technical failure also needs to be tested and repaired by a professional watch repair shop.

5.Watch magnetization: Watch magnetization is one of the common reasons for the inaccuracy of the watch, even if it is an anti-magnetic watch, even if it is an anti-magnetic watch, it cannot be placed next to electrical appliances with magnetic fields, such as TV, automatic mahjong machine, etc.

Because some of his parts are not anti-magnetic, they will still be magnetized over time. The watch is magnetized and needs to be demagnetized by a professional watch repair facility.

Reasons for Audemars Piguet watch to stop and how to deal with it:

1) Audemars Piguet mechanical watch accuracy, in fact, will also be affected by the external environment and changes, in particular, the mainspring full or half string, external force caused by swing, vibration, magnetism and other conditions, as well as the impact of temperature and temperature is also quite large, full mechanical watches are divided into single winding and two-way winding, most of them are two-way winding, should not be this problem, no matter how the rotor turns is in the winding, you don't have to worry. There are two reasons for stop-and-go, one is that there is no string, even a self-winding watch requires you to swing your arm every day (at least 8 hours), and when you sleep at night, it is not winding, and the string will stop naturally if it is not enough, and you will automatically wind it when you swing your arm, and it will walk again.

2) In addition, if the Audemars Piguet watch is not matched for a long time, the lubricating oil will freeze, and it should be sent to a watch repair center to have the technician put some oil on your watch. Generally, it is recommended to maintain the watch once after about 3 years of use. There have been inadvertent bumps in life, ask the master to show you.

Under normal circumstances, there is a slight error, as long as it is not a watch, there is generally no problem.

Click to contact an Audemars Piguet Watch After-Sales Service Center.

The more common reason may be a lack of kinetic energy, but some friends may say that I buy a fully automatic mechanical watch, and I don't need to wind it myself. In fact, this is a big misunderstanding, automatic mechanical watches do not need to be wound manually, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch is the use of the arbitrary swing of the rotor to wind up, and the rotor is swinging with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But what if you wear it on your hand a lot and don't leave? Don't worry, it may be a lack of kinetic energy, and then we need to manually wind the clockwork.

After passing the above methods, what should I do if I also find that the machine is not gone? Here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be that the mechanical watch is faulty, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair. Before the watch bar talked about the maintenance method of mechanical watches, mechanical watches need more maintenance than quartz watches, here is an emphasis on the maintenance methods of mechanical watches:

1.If it is a manual mechanical watch, the mechanical watch should be wound regularly, and it is recommended to wind the mechanical watch around 8 pm.

2.Automatic watches, such as insufficient arm movement, need to manually wind the watch, and the rotation of the crown needs to be controlled within 20 turns.

3.If an automatic watch has not been worn for more than 40 hours, it is necessary to turn the crown twenty times to activate the movement's drive system.

4.Regardless of the water resistance of the watch, it should be avoided as much as possible, and if it does, wipe it dry and make sure that the crown is locked at all times. It is best to replace the waterproof ring once a year.

What should I do if the mechanical watch is gone? We need to establish the common sense of protection of mechanical watches in ordinary times, and when we encounter the situation that we can't go, we don't need to worry, and we can eliminate them one by one according to the above methods, which are usually caused by insufficient kinetic energy.

Hello, glad to answer for you!

The main reasons why the watch does not go are the misalignment of the core gear, the magnetism of the watch, bumps, and the long shelving time, and the oil sludge is dry. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch suddenly stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours.

If the quartz watch stops suddenly, it may be caused by a dead battery, so you can take the watch to the after-sales center to replace the battery.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

Audemars Piguet watch after-sales center in: Shanghai Huangpu District Nanjing East Road No. 299 Hongyi International Plaza 10th Floor Room 1003, when your watch fails, you should go to the regular after-sales center, by a professional technician to carry out a comprehensive maintenance and inspection of the watch, all accessories in the after-sales center are original original, to maximize the life of the watch!

In fact, there are many reasons why the mechanical watch does not go, and there are generally two types, the first is because of the lack of kinetic energy. The second is due to a malfunction of the mechanical watch. Therefore, don't panic too much when you find that the mechanical watch is not leaving, first distinguish which kind of big it belongs to, and you can also directly take the watch to the after-sales center and let the technician test it.

Quartz watch: 1. Quartz watch is mostly parked due to insufficient battery power, and the battery needs to be replaced.

2. The circuit board and other parts of the quartz watch have poor contact, which is also the reason for the watch to stop.

3. If there are some gear train faults in the quartz watch movement, it will also lead to the watch being stopped secretly, and the problem will be repaired in time.

Mechanical watch: 1. Wear more than 10 hours a day, especially automatic mechanical watches, the efficiency of automatic winding is low, and the amount of arm activity is larger, and the range of movement of the wrist is too small when wearing the watch to type on the keyboard, and the winding efficiency is very low. If the amount of exercise is small, it can be wound by manual winding.

2. Pay attention to the shockproof, dustproof, anti-magnetic and waterproof of the watch. It's a good idea to take your watch off when doing strenuous exercise or doing laundry or bathing.

3. Remember to take care of your watch, if you don't maintain it for a long time, a lot of sludge will be generated and silted inside. Friction between gears increases, causing slippage.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the store for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy.

3. Having been beaten or impacted. The watch is very tight, if it is hit or dropped, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to the store for testing.

4. Maintenance is required. A lack of oil or wear and tear of the internal parts of the movement can cause time-keeping problems and require maintenance.

5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the error of the time, which will be sent to the store.

Note: 1. Mechanical watches vary according to the model and manufacturing quality of the movement, and the error of the general watch within 30 seconds per day is within the normal range. Some of the higher precision movements can reach around 10 seconds.

First of all, let's first understand the working principle of a fully automatic mechanical watch, there will be a gyroscope in the movement of the watch, this gyroscope can also be called a self-winding device, when people wear the watch on the wrist, the gyroscope will rotate with the swing of the human arm, and when it rotates, it is equivalent to automatically winding the watch to ensure the normal operation of the watch. Therefore, if the arm does not move enough to fill the watch with enough springs, the watch will run out of power and will slow down or stop at all.

Nowadays, many people sit in the office when they go to work, and they mostly drive or sit in a car on the way to and from work, rarely exercise, and the lack of activity can not make the gyro automatically wind the watch, which leads to the phenomenon of the watch stopping is becoming more and more common. In fact, the automatic mechanical watch does not need much exercise to ensure its normal operation, usually consciously swing the watch, walk more, wear the watch for more than 8 hours a day, basically can maintain the watch work. If there is really no way to give the watch enough power, then you can also choose to wind it manually, and the effect is the same.

The new watch has a high sensitivity, and it may be possible to travel for a long time with a little movement or a few winding cycles. However, when the watch is worn for a period of time, the parts have a certain amount of wear, and the lubricating oil between the parts will slowly volatilize, so that the friction resistance between the gears increases, so give the same power, the efficiency of its work is greatly reduced than when you buy it, and at this time you need to take the watch to a professional after-sales maintenance center for routine cleaning and maintenance.