What should I do if the bathroom is leaking, but I don t want to smash the tiles?

There are special tile refurbishment materials, such as tile surface treatments, floor tiles, and mosaic binders, which can be applied directly to the tiles.

Then lay the new tiles on the top, saving the time and energy of eradicating the old tiles in the middle, or if the tiles are not damaged, but there is a problem with the joints between the floor tiles, then you only need to remove all the floor tile joints and redo them.

If the age of the house is relatively old and the waterproofing of the bathroom is not good, it is recommended to dismantle all the bathrooms and redecorate and renovate them.

It can be repaired with a new type of penetrating waterproofing agent to find the leaking part of the bathroom, and then brush the waterproofing agent on the surface of the leaky part so that the water cannot enter the ground and drain directly from the waterway. But this is only for the phenomenon of leakage of the waterproof layer, if there is a leakage problem in the upper and lower water pipes, then the tiles must be smashed.

There is also the problem of horizontal leakage in the bathroom, that is, the mold and peeling of the corner of the wall caused by the door stone problem, and you can also choose to avoid smashing bricks and waterproof construction. Of course, there are many reasons for water leakage in the bathroom, and the specific choice of brick-smashing scheme or non-brick smashing scheme requires a professional waterproof maintenance master to determine through the actual analysis and judgment of the site.

Step 1:

If the caulk between the gaps in the tiles in the bathroom is intact, then mix the caulk with water and wipe the gaps directly, and wait for 12 hours for the new caulk to dry!

Step 2: If the caulk between the tile gaps in the bathroom is full of holes, then directly use a shovel to clean all the previous tile gaps, then refill the tile caulk, and then wait for 12 hours for the caulk to dry.

Step 3: Then use a screwdriver to pry open the iron cover of the anti-leak agent, directly dip the brush into the anti-leakage agent, and brush it to the gap of the tile.

Step 4: When brushing the anti-leakage agent, you only need to brush the gaps of the tiles, and the tile surface does not need to be brushed.

Step 5: After brushing the leak-proof agent, the room is ventilated and breathable, which accelerates air circulation and saves construction time.

Step 6: After 12 hours after construction, the leak-proof agent penetrates into it, and it can be used for water after drying.

Step 7: The anti-leakage agent is penetrated into the building, not the film formed on the surface, and it is okay to walk, sweep, mop and rub in the future.

Answer: In addition to surface water seepage, there is also a leakage of pipes after the bathroom is renovated; There are many such situations, such as floor drain leakage, toilet pipe leakage, and upper and lower pipe leakage. Methods for checking for leaking pipes; First: if there is a leak when you open the faucet, and the leakage decreases immediately when you close the water pipe, it means that the upper and lower water pipes in the bathroom are leaking.

The second is that there is no water, but the water meter pointer is still jumping, which means that the water pipe is leaking; The third leakage may be the leakage of the drainage pipe, because it is buried in the ground, it will be relatively hidden and not easy to find.

1. Determine the cause of water leakage

It is necessary to stop the water in the toilet and wait for the toilet to dry completely before observing

1.If water continues to leak out of the toilet when it is not being used, it is a leak caused by a ruptured water pipe. At this point, the bricks must be smashed to repair it.

2.If the bathroom does not leak when it is not watery, the slightest water will leak. This proves that the sewer pipe is broken, and it can be repaired without smashing bricks.

3.If the water leaks only when there is a large amount of water or stagnant water in the bathroom, it is usually because the waterproof layer is damaged, or the corner waterproof is not perfect. At this time, you can also not smash bricks.

Second, the sewer pipe leakage - plastic steel mud

If you look at the downstairs ceiling if you look at the leaking sewer pipe, you can usually see obvious damage points - the water is seeping out from the pipe, and there are no water stains on the ceiling.

This kind of problem is easier to solve: buy a product called "plastic steel clay", which is like plasticine that we played with when we were children. Wrap it around the water seepage points on the pipes, and after waiting for it to dry naturally, it will become hard and feel a bit like plaster.

The dried plastic steel mud has a strong viscosity and can block the water seepage point.

3. Damage of waterproof layer - permeable waterproofing agent

There are water stains on the outer wall of the bathroom, and it is damp to the touch. Or there are water stains on the ceiling downstairs – usually around the pipes or in the corners of the walls.

At this time, you can buy a penetrating water repellent agent, pour it into your own bathroom (remember to plug the floor drain in advance), spray it on the wall, and wait for it to dry naturally.

After 24 hours, the water repellent that was originally a liquid will turn into a jelly-like form. At this time, just remove this layer of "jelly" and clean it up.

Penetrating waterproofing agents will leak water down the floor or exterior wall along the path of water seepage, and as it dries, it will plug up the damage in the waterproofing layer.

1. How to deal with toilet leakage without smashing bricks: use waterproofing agent. The waterproofing agent penetrates into the mortar layer through the gaps in the tiles and reacts in the mortar layer to form water-insoluble colloids and crystals, thereby blocking the leakage channels of capillary pores and cracks.

2. It is integrated with the mortar layer to achieve thorough waterproofing and leak plugging.

2. How to judge whether the bathroom pipe is leaking:

1) Do a pressure test: carry out a water pressure test, inject pressure into the water pipe, stabilize the pressure for about 10 minutes, if the pressure is not reduced, it is basically not a water pipe leakage, if the pressure is reduced a lot, it is basically caused by the rupture of the water pipe.

2) Observe the state of the water: if there is a leakage in the upper and lower water pipes of the bathroom, there is an obvious performance, that is, the water leakage is intermittent and intermittent, especially when the faucet is turned on, the water leakage is serious, and the water leakage is reduced when the water pipe gate is closed, the water pipe leakage is in a dripping state, and the ground is still wet when there is no water.

3) Observe the water meter: If the water meter still has a slight jump phenomenon in the state of no water, it can be proved that the water leakage is caused by a problem with the water pipe.

How to deal with toilet leakage without smashing bricks and maintenance method 1 When the toilet leaks, if the user does not want to smash the floor tiles for maintenance, you can first find the specific leakage location, and then apply the permeable waterproofing agent to the surface of the leakage location, so as to prevent water from penetrating into the ground and allowing the water to only be discharged from the drain. 2 However, this method is only suitable for repairing the leakage of the toilet waterproofing layer, if the leakage of the toilet is caused by the upper and lower sewer pipes, then all the toilet tiles must be smashed open for repair. There are many reasons why a toilet can leak, and depending on the cause, the treatment measures taken will be different.

3 When there is a leakage in the toilet, it is generally necessary to arrange specific maintenance matters according to the severity of the toilet leakage and the specific location of the leakage. If the leakage of the toilet is more serious, then it is necessary to smash all the toilet tiles of the sedan car for repair, and the waterproofing layer must be redone. 4. If the user does not want to smash the floor tiles for maintenance, and the toilet leakage is relatively slight, then you can use caulk to repair the leakage of the ground cracks, and then use a special waterproof coating to apply a waterproof protective layer on the ground cracks and leaks.

5 When the toilet leaks, if the floor tiles are smashed open for maintenance, the waterproof layer of the toilet floor will inevitably be destroyed, and once the waterproof layer is destroyed, it will not be able to play a good waterproof effect.

Summary. 1. How to deal with the leakage of the bathroom without smashing the bricks and how to repair it.

1. Clean the bathroom floor first and check what the cause of the water leakage is. If there is a slight leakage and the water pipe is not damaged, you do not need to smash the tiles, and you need to use a penetrating waterproof material.

2. Keep the ground dry enough, and then apply the permeable waterproof coating to the ground, paying attention to every part to be smeared, and no leakage.

3. After the waterproof is dry, you need to use glass glue with good waterproof performance or beauty sewing agent in the gap of the tile, and wait for it to dry thoroughly after treatment.

4. If the water pipe is broken, it is generally necessary to smash the tiles and then repair the water pipe. If you don't knock on the tiles, you can only reinstall the water pipe to ensure the later use.

How to deal with toilet leakage without smashing bricks and maintenance methods.

Hello. Can construction be done in Fangshan District, Beijing.

1. How to deal with the leakage of the bathroom without smashing the bricks and maintenance methods 1. Clean up the bathroom floor first and check what the cause of the leakage is. If there is a slight water leakage and the water pipe is not damaged, the lead does not need to be smashed and lifted off, and a permeable waterproof material is used. 2. Keep the ground dry enough, and then apply the permeable waterproof coating to the ground, paying attention to every part to be smeared, and no leakage.

3. After the waterproof is dry, you need to use glass glue with good waterproof performance or beauty sewing agent in the gap of the tile, and wait for it to dry thoroughly after treatment. 4. If the water pipe is broken, it is generally necessary to smash the tiles and then repair the water pipe. If you don't knock on the tiles, you can only reinstall the water pipe to ensure the later use.

With the gradual stabilization of the epidemic situation in Beijing, the District Urban Management Committee actively helped the construction waste elimination and disposal site and construction waste transportation enterprises to resume work and production, standardize the management of muck, and achieve both epidemic prevention and control and resumption of work and production.

Method 1: Clean up the bathroom, scrub the dirt in the corners and seams with a brush, and let it dry. 2. Seam repair:

If there are obvious cracks, they should be repaired with cement slurry. 3. Splashing: cover the floor drain with plastic film, then pour the bathroom plugging agent onto the ground, and then slowly push it around with wooden boards and other tools, and require the entire bathroom floor to be soaked in the plugging agent for 30 minutes.

4. Wipe dry: wipe the excess plugging agent remaining on the ground after 30 minutes or 1 hour. 5. Maintenance:

There is no open water shower within 24 hours. Method 2 1, do not smash the brick waterproof plugging can also use the grouting method, that is, in the bathroom without smashing the brick waterproof plugging construction, relying on the natural type of dust infiltration of the waterproof agent, under the tile reaction to generate insoluble colloids and crystals, blocking the capillary pores, capillary leakage water channel, playing the role of waterproof plugging. 2. The premise of construction is that the water under the tile is not sufficient, but in some occasions or after the water consumption is larger, the reality does not allow enough time to ensure the evaporation of water under the tile, grouting is carried out in an inconspicuous position in the bathroom, and the water under the tile is squeezed out by grouting method, and the waterproofing agent reacts in the leakage water channel under the tile to generate water-insoluble colloids and crystals, which plays a thorough waterproof plugging role.

The use of low-viscosity two-liquid grouting machine for waterproof and leakage plugging construction without smashing bricks greatly improves the construction efficiency.