What are the solutions to a leaky toilet?

The solution to the problem of toilet sewer pipe is to carefully check the interface between the toilet bowl and the sewer pipe, whether it is loose, or the pipe is rotten, at this time, if the pipe is rotten, you need to replace the pipe, if it is, it is not connected, you need to use some wire or the like from the outside to buy some materials that can fix it, and fix it.

For the problem of water tank material, the best solution is to separate the toilet tank, one by one to check whether the parts in the toilet tank are in good condition, if there are some parts broken, can be repaired, it is best to replace the one that can not be repaired, if it is too inferior to the pumping tank, rotten more, it is recommended to replace the entire water tank, so as not to bring more serious consequences.

1. What to do if the water in the toilet keeps flowing - the reason.

1. Check the material problem of the water tank.

If the material selected for the water tank is not good or aging, there will be a problem of water leakage, now the progress of the toilet industry is rapid, there are many toilets on the market, but there is no guarantee that some fake and shoddy toilets appear, many businesses in order to make money, create some indiscriminate toilets, in order to seek more benefits, choose inferior materials, this kind of toilet just look at the surface can not see a reason to come out, they may be some internal parts of the problem, It won't take long for it to be damaged, and of course, it is not excluded that some toilets that have been used for a long time are damaged as a natural phenomenon of aging.

2. There is a problem with the sewer pipe.

There is also a problem caused by the sewer pipe, which is a pipe that is directly connected to the toilet to transport water, and if there is a leakage, the sewer pipe also has the main cause, which is very likely.

3. The drain valve of the toilet.

The drain valve is in control of the water in the toilet tank, if the above two reasons can not be checked, then you should check the problem of the drain valve, in many cases, it will make the drain valve problem, it may be because of the installation hole cracked and deformed, or a series of problems such as unevenness during installation.

Second, what to do if the water in the toilet keeps flowing - the solution.

1. Separate the toilet from the water tank, check whether the parts are intact, if it is because some small parts are damaged, it can be repaired, and if it cannot be repaired, it will be re-bought to install, for some too inferior water tanks, it is recommended to replace the entire water tank, so as not to bring more serious consequences.

2. The best solution for the toilet sewer pipe is to check the connection between the sewer pipe and the toilet to see if they are loose, or whether the pipe is rotten, if it is because the pipe is rotten, you need to replace the new pipe, if it is not connected, you need to fix it with wire or some materials that can be fixed.

3. If the water leakage is caused by the drain valve, it is more complicated, because it involves some professional knowledge, you can ask a special maintenance master to come, so as to ensure the normal use of the toilet.

1. If the tank is drained, the float and the float rod will affect the reset of the flap and cause leakage. In addition, the float is too long and the float is too large, which leads to friction with the tank wall, affects the free rise and fall of the float, and leads to seal failure and leakage. The mechanism of the tank fittings caused disturbances during operation, which led to leaks.

2. The quality is not good. Manufacturers blindly reduce production costs When the inlet pipe and inlet pipe of the injection valve are injected, the poor material will cause cracks, resulting in the failure of the seal, and the water in the tank enters the toilet bowl through the overflow valve, overflow pipe, resulting in a long flow of water.

3. When the water pressure is very high, if the buoyancy of the float is insufficient due to the excessive pursuit of the miniaturization of the tank accessories, if the float overflows, the water inlet valve can not be closed, so that the water continues to flow into the water tank, and then into the toilet, and there is a vertical situation of water leakage.

4。The height of the lift inlet valve can be changed freely, and if the seal does not fit tightly with the pipe wall, leakage may occur. The fitting of the drain valve is not tightly sealed.

Disposable drain valves manufactured in a single use cannot be tightly sealed through a fitting. When hydraulic pressure is applied, water flows into the toilet bowl through the overflow pipe from the interface gap, causing the toilet to leak.

The most fundamental way to replace it is generally that there is a gap between the base and the ground, and it can be treated with special glue to plug the leakage.

Steps. 1. Check whether the inlet valve and outlet of the toilet are broken; Steps.

2. If it is ruptured, it needs to be replaced with a new one; Steps.

3. Check the connection of the drain valve, if it is a problem here, it needs to be reinstalled; Steps.

Fourth, check whether it is a problem with the floating rod and float, if it is not suitable for their design and style, then they need to be replaced with a suitable one.

Steps. First, first check the position of the inlet valve and outlet in the toilet tank that the jujube is not broken.

Steps. 2. If a rupture is found, a new inlet valve needs to be replaced as soon as possible.

Steps. 3. Check whether the connections of the lower drain valve are damaged or loose, and if so, the cocoa has been newly installed.

Steps. Fourth, check whether there are design defects in the float and float rod in the tank, such as the float rod is too long or the float is too large to affect the normal lifting and cannot be reset freely, which needs to contact the after-sales service or replace the suitable one.

The problem of toilet leakage is basically in the water tank, so the menhir book needs to be disassembled and checked one by one, if it is loose or stuck, then you can solve it yourself, if it is because of damage, aging, etc., you need to let the maintenance personnel replace the new one. So if you want to avoid these problems, be sure to check the quality of the parts in the drain tank before buying a toilet.

The toilet leakage in our home is often a problem due to infrequent inspection or improper use is the toilet leakage, and the bathroom is full of water, which not only wastes water but also affects our normal life. So we have to solve this problem as soon as possible, one. Causes of leaking toilet seats.

1.Leakage of the toilet caused by the aging of the parts inside the water tank.

2.Water leakage caused by backflow of sewage due to poor toilet drainage.

3.The toilet flush switch is leaking.

4.Because the rubber gasket at the drain is aging, it leaks.

Two. What are the ways to deal with toilet leakage?

1.If the rubber ball valve is damaged, the seal is not tight, and there is a water leak, it needs to be replaced immediately.

2.Water tank leakage, basically a drain valve problem, check the water tank outlet rubber plug, if the water outlet rubber plug is damaged or there is a foreign body blockage resulting in the rubber plug is not tightly sealed, it will also cause the toilet to flow more than once.

3.Check if the flush switch is reset. The plastic flush switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored. Generally, the switch can be reset by repeating it a few times.

4. Check whether the rubber gasket of the drain is aged, the seal is not tight, and the problem needs to be replaced.