-
Hello, my family is also this problem, the bathroom waterproofing has been redone, how long can the living room wall be dry?
-
This water leakage may be caused by a leak in the water pipe, or it may be caused by a leak in the waterproof layer, so you should first figure out the cause of the leakage, and then find the right solution to the problem.
1. Water pipe leakage.
Caused by water pipe leakage, it is necessary to find the leakage point of the water pipe, plane the wall tiles, then find the joint part of the water pipe, check whether the partition water pipe is leaking, find the leakage point, replace the water pipe or interface, and finally lay the wall, re-do the waterproofing, and restore the tile surface.
Second, the waterproof layer leaks.
If it is caused by the waterproof layer, it is necessary to find the leakage location of the waterproof layer and repair the waterproof layer. Shovel off the surface tiles, find the gaps between the surface tiles, smooth them with waterproof plugging treasures, and brush the walls with waterproof paint. If the water leakage is caused by insufficient waterproof height, the tiles at the height should be planed, and the upper wall should be re-waterproofed and re-tiled.
The exterior wall must have been ruined, so what should be done with the façade?
a) tiled facades.
Clean the surface of the external wall first, check the tile joints of the external wall for cracks, and repair the cracks with gray waterproof material after drying. After the waterproofing material is completely dry, paint the tile joints with waterproofing material or paint the exterior wall twice with waterproofing material, with an interval of about 4 hours between each coating. Although it is more effective to paint the exterior wall with waterproofing materials, tiles that have been coated with waterproofing materials will be prone to dust absorption due to electrostatic effects in the future.
b) Coated exterior walls.
Remove the old paint on the surface as much as possible to ensure that there is no oil, dust, mud and other dirt on the surface. After drying, repair with a gray waterproof material. After the waterproofing material is completely dry, apply two to three coats of waterproofing material paint to the exterior wall, and the interval between each coating is about 3 to 6 hours.
c) Cement walls.
Clean the walls, check for cracks, and repair them with gray waterproof material after drying. After the waterproof material is completely dried, it can be painted with waterproof material.
It's not that hard, right? However, there are some precautions, so don't be careless.
1. If it is the exterior wall that was originally pasted with tiles, and the water leakage belongs to the junction of the floor slab or the window frame, then the above-mentioned construction method may fail because of the cracks in the handover of the floor slab and the cracks around the window frame, so it is recommended to find a professional to deal with it.
2. The process of crack inspection is very important, and the crack should be repaired in advance, otherwise it will affect its effect.
3. The waterproof material should not be brushed too thickly, as long as the place that has just been brushed is slightly white, and too much brushing will affect the effect.
-
The pipes are buried under the waterproofing layer, and during the renovation, there is almost no water in the water supply pipes – even for closed water tests.
, the time for filling the pipes with water is also relatively short. So if it is a leak in the upper pipe, it can only be detected after normal water use. Use red bricks and waste tiles as a void layer, and plaster cement mortar on top.
Then do a layer of waterproofing, all the interface positions of the drainage pipe have been specially treated, especially the position of the main drainage pipe and the floor through should be strictly guarded! Every link must not be careless and <>
When doing waterproofing, the paint is unevenly smeared, and the waterproof paint is applied.
The quality is not up to standard, the waterproofing is not done in accordance with the process sequence, and the wall is not leveled, which may cause water leakage in the bathroom. It is important to decorate in the order of the process. Before the bathroom is waterproofed, it should be thoroughly cleaned, so at this time the decoration company is required.
If they are unqualified, let them rework in time and not leave themselves with hidden dangers. At this time, the leakage of the toilet is estimated to have appeared here, and the waterproof layer or pipeline on the ground was damaged during construction, resulting in water leakage.
There is no problem with the water supply and drainage pipes, then, the entire bathroom floor, first put the floor drain.
Plug it, put water bubbles to see, and see if it leaks from the tile joints and causes water accumulation throughout the caisson! There is also the fact that the water pipes embedded in the wall are not treated with multiple waterproofing treatments before backfilling, resulting in the water used in the backfill seeping into this place from this place, which is a small chance, 3, and the natural settlement of the backfilled garbage destroys the secondary waterproofing.
If the sewer pipe is leaking, there will be damp around the pipe and water droplets will settle down the pipe, and the leak will also be found and repaired. If the waterproof layer is damaged, there will be overflow in the corner of the wall and the floor of the floor.
Wet, the most complicated treatment is to pry all the waterproofing, there will be a higher position, if the water is not enough to submerge the high place, it will leave hidden dangers; Then there is the lack of water to test the water, and the water is almost evaporated, so there is no point in testing it later.
-
Yes, this situation is generally because the waterproofing is not done well, so it will lead to water leakage and seepage in the bathroom, and you should check it.
-
Yes, you need to check that the bathroom is ** water seepage, and then remedy it in time, it may be that the plates are not connected well, there are gaps, resulting in water leakage, please repair the workers in the past.
-
Not necessarily, but it is likely that there is water seepage in this case, and it is also possible that the pipes in the walls are broken.
-
It is because the waterproofing is not done well, when decorating the bathroom, the waterproof must be brushed with two layers, so that the waterproofing can be done well, and there will be no water seepage.
-
Yes, it must be because the bathroom is not waterproofed well, and it could also be because the people upstairs have not done the waterproofing of the bathroom.
-
It may be because the waterproofing is not done well, or it may be because the ceiling of the bathroom is damaged.
-
Can be handled with water-soluble liquids. Bathroom waterproofing after testing water leakage treatment method:
1. Use water-soluble liquids and wear protective gloves when using. Do not swallow or splash into eyes, rinse with water if contacted.
2. The surface of the base should be smooth, solid, clean, no oil stain, no clear water.
3. Add 23 to 25L of clean tap water with a water temperature of 18 degrees plus or minus 2 degrees in the bucket (hot water and warm water are prohibited), open the A1 material package and pour it into the water and stir it well until there is no particle, which is subject to the naked eye. Then add A2 and stir well, and finally add B and stir well (the total mixing time should not be too long, about 5 minutes is appropriate).
-
After the bathroom is waterproofed, the water leakage is tested: 1. First of all, you need to analyze the cause of the toilet leakage, if the water inlet valve is turned off, the water leakage and dripping will stop. After the bathroom water inlet is opened, the downstairs water leaks continuously, which means that the toilet inlet pipe is leaking; If there is no problem with the water inlet pipe, you can divide the sewer pipe such as wash basin and toilet to flush the water, if the water leakage downstairs is aggravated, it means that the sewer pipe is leaking.
If there is no problem with the bathroom plumbing, it means that the waterproof layer is leaking.
2. If there is a problem with the waterproof layer of the bathroom, you can use a new type of penetrating waterproofing agent, first clean up the caulk of the bathroom tiles, then brush the penetrating waterproofing agent, and finally fill the tile joints with waterproof paste. Or you can do the waterproofing of the bathroom again, and carry out a closed water test after the waterproof layer is done.
3. If there is a leak in the bathroom water pipe, and the upper and lower water pipes are on the ground, find the location of the leakage, remove the tiles in this range, and then replace the broken water pipe; Or buy a special adhesive and apply it around the cracked water pipe, using the adhesive to bond the leaky water pipe together. Nowadays, many people are asking the decoration company to carry out interior decoration, and the general decoration company will give a certain warranty period to the project, if it is within the warranty period, the owner can ask the decoration company to deal with the problem of water leakage in the bathroom.
-
Check the cause of the leakage, and if the waterproofing is not done well, re-do the waterproofing.
-
Hello! This situation proves that the waterproofing is not done well, and it needs to be re-done.
-
If it is done with money, hit ** to give the warranty.
-
Then it proves that the waterproofing is not done well, and it is redone, what kind of brain-dead questions are these!
-
When this happens, I see that they have all planed the tiles in the bathroom, re-waterproofed, and re-glued the bricks. It's redecorated again, and it doesn't seem to be a good way.
-
1. Treat the dust, oil and stagnant water at the leakage site first, so that the surface of the bathroom is dry and clean. 2. If you want to use caulk to fill the tile joint, you should first use a knife to cut a small groove in it. 3. The penetrating waterproofing agent should be evenly sprayed on the place where the cement needs to be plastered.
4. After the waterproofing agent is dry, then fill the gap paste on the tile joints or damaged places, and reinforce them with grout paste around the root of the pipe. 5. The ground and the pipe root are made of plastic steel mud as waterproof edges. 6. After the waterproof construction is completed, it cannot be drenched within 24 hours.
-
The bathroom decoration is waterproof, and how to deal with water seepage downstairs.
Dear users, if your bathroom decoration has done waterproof measures, but there is still a problem of water seepage downstairs, you can consider the following ways to deal with it: 1Check that the waterproof layer of the bathroom is complete
If the waterproofing layer in the restroom does not fully cover critical areas such as corners, floors, and drains, it can lead to water seepage problems. You can ask a professional waterproofing master to check whether the waterproof layer is complete, and repair it in time if there is a problem. 2.
Check if the drainage system is in order: If there is a problem with the drainage system in the restroom, such as a clogged drain pipe or an improperly located drain outlet, it can also cause water seepage problems. You can ask a professional plumber to check whether the water system is normal, and if there is a problem, fix it in time.
3.Canasia Soundproofing: If your bathroom is not renovated with soundproofing in mind, it can cause noise disturbances for the residents downstairs.
You may want to consider adding acoustic insulation to your bathroom floors and walls to reduce noise transmission. 4.Negotiate with the residents downstairs to settle:
If none of the above measures can solve the water seepage problem, you can negotiate with the residents downstairs to solve the problem. You can consider jointly asking a professional waterproofing master or plumber to check the problem and share the repair cost. Hopefully, the above tips will help you solve the problem of water seepage in your bathroom.
-
1 First of all, I have to answer that there is a remedy for not moving the tiles, which is to find a clear leak or crack and plug it. That's it. But I have to tell you, this method is purely a headache cure, and a sore foot cure. Treat the symptoms but not the root cause.
2 Therefore, the most fundamental way is to knock off the tiles and redo the waterproofing. At the same time, warn: all the construction that wants to save the trouble will come to you in the end.
In view of your mentality, it is also recommended that you should never buy some inferior waterproof materials in order to save material costs.
3 For toilets, the appropriate material is a polymer cementitious waterproof coating. Good brands are, JCDecaux, Yuhong, Lei Bangshi...
4 Hope it helps!
-
It depends on the specific leakage, the water has seeped, which proves that the waterproof has failed, and I can't think of any way to make up for the failed waterproof! More information, better suggestions, free concrete waterproof leakage repair technical consultation, free of charge to avoid today's repair, tomorrow's leakage, every year repair, every year leakage trouble.
-
The only way is to dig the tiles and do it again, decoration this thing must pay attention to, especially waterproof, it is recommended that you do the waterproof after the closed water experiment for 3 days, don't be afraid of trouble, if you don't leak you brush a layer, waterproof treasure is not expensive, but the labor is not cheap, want to do more than a few more times if you want not to leak.
-
I dismantled it and redid it, there was no other way.
-
It can be injected and can be waterproof.
Bathroom leakage generally does not involve the wall, if you knock on the wall, you only need to pay attention to whether it is a load-bearing wall. However, the waterproofing of the ground should be expanded. The location of the bathroom after expansion must be waterproof!
The first step, before the waterproof treatment of the bathroom, the first thing is to level the floor level of the bathroom, the ground is uneven, when the waterproof paint is painted, it may be uneven, or the ground is easy to crack because of unevenness, which will crack with the ground even if the waterproof paint is applied. >>>More
Directly on the waterproof paint. And I personally recommend that in the shower room, a position with a lot of water, don't brush to a meter as required, and brush it directly to the top. Stay on the safe side.
There is more moisture in the bathroom, so it is necessary to pay attention to the waterproof treatment during the decoration process, and the waterproof must be in place to avoid the problem of water leakage, and the later maintenance is more troublesome. Secondly, the choice of waterproof coating for the bathroom is also very important, what materials are used for waterproofing in the bathroom? It can be mainly divided into the following types: >>>More
First of all, you have to know what is missing.
Only then did I know that I needed to block **. >>>More