Floor drain installation method What are the floor drain installation steps

Floor drain installation steps.

1. Remove the cement near the floor drain first, so that the floor drain is separated from the cement and is easy to take out. Knock down the old floor drain, which cannot achieve the effect of anti-odor.

3. Scrape cement putty near the floor drain to make contact with the ground. The floor drain is aligned with the middle of the drain pipe, put it in its original position, and install it.

4. Install the inner core, which has an anti-odor effect and can be taken out for cleaning at any time. It can be used after the cement is coagulated.

Floor drain is one of the most common building materials in our home life, whether it is kitchen and bathroom space, or balcony is essential, what is the installation method of floor drain? Next, let's take a look at the installation method of floor drain.

Floor drain installation method, step 1, first of all, the materials required for the installation of floor drain: slotted screws, small hammers, chisels, cement putty, three-proof floor drains, scrubbing Pa.

Floor drain installation method, step 2, check the drain pipe: before the floor drain is installed, you need to check whether the drain pipe is blocked, and the drain needs to be protected before putting in the floor drain, so as not to be blocked by foreign garbage pipeline.

floor drain installation method, step 3, after cleaning up the cement debris, scrape the cement putty around the pit wall; The reverse side of the floor drain is also scraped with cement putty to make them firmly combined.

Floor drain installation method, step 4, the center of the floor drain is facing the center of the drainage pipe, put it into the pit, and press it hard.

Floor drain installation method, step 5, after pressing firmly, wipe off the excess cement putty with a scrubbing pad, and clean up the cement debris garbage on the ground.

Floor drain installation method, step 6, kitchen and bathroom floor drain installation pay attention to slope treatment: kitchen and bathroom installation floor drain must pay attention to slope. "Water flows to a low place" I believe everyone understands, the same is true for kitchen and bathroom water, when paving, you need to make a certain slope around the floor drain, so that the water can flow down naturally.

Floor drain installation method, step 7, the last step is to install the cover, wait for 24 hours, and the cement can be used after setting.

About the floor drain installation method.

When we decorate a new house, we usually install floor drains in the three areas of hygiene, balcony and kitchen, and how to install floor drains, if the newcomers must not know where to start, it seems simple, but there is no way to take it. Today I will teach you a trick: how to install the floor drain, and several ways to install the floor drain correctly.

How to install the floor drain.

1. Before installing the floor drain, the props should be prepared: screwdrivers, small hammers, chisels, cement, towels, and of course, the floor drain must be indispensable.

2. It is also necessary to inspect the drainage pipes in the lower room to see if they are blocked. Otherwise, it will be very troublesome to find that the floor drain is blocked after installation.

3. The floor drain should also be complete and able to be used normally: the main heart of the floor drain should be guaranteed to be able to open and close normally, and the sealing must be good.

4. Clean the pipeline: first flush the inside of the pipe with water, then take the prepared towel to plug the pipe mouth tightly, clean the surroundings, and remove the cloth. Note that no foreign matter remains inside.

5. Smear cement near the drainage port of the pipeline, and then smear enough cement on the back of the floor drain, so as to ensure that the floor drain and the drainage outlet are tightly combined.

6. The last step is to smear enough glass glue near the mouth of the drainage pipe and put the floor drain sleeve into the drainage pipe. After installation, don't forget to clean up the trash near the floor drain.

There are several ways to install a floor drain correctly.

The first type: diagonal cutting method.

If the installation position of the floor drain is in the positive position of the tile, then the tile needs to be cut along the diagonal line to get 4 fast equilateral triangles.

The second way: four-side cutting method.

No matter what position the floor drain is in, it can be installed in this way: in the center of the floor drain, the side length is about 12cm square area, and then make a quick diagonal in this area, when pasting tiles, be sure to make a gentle slope, so as to ensure that the water flows into the floor drain. This installation method is not good looking, but it is very practical.

The third type: cross-shaped paving.

The installation method is to use the floor drain as the center point for paving, this method can be said to be better, can not let the floor tiles maintain integrity, and from the appearance looks very beautiful, of course, there should be a slope.

Fourth: edge break.

This method is suitable for the situation where the floor drain is located at the edge of the wall, in the small area closest to the wall, the floor tiles are pasted in a straight shape, and only the middle of the tile needs to be reserved for the floor drain.

1. Match the floor drain in advance according to the caliber of the sewer pipe shirt.

Before buying a floor drain, you should know the diameter of the floor drain sewer pipe, which is generally 50 PVC pipes now, and the cast iron ones are larger. The selected floor drain water diameter should match the diameter of the PVC pipe, and the reserved holes for drainage are generally large when burning and delivering, and the decoration needs to be trimmed, and the drainage outlet should be done according to the size of the floor drain, do not trim the drainage outlet first, and then go to buy the floor drain.

2. The location of the floor drain installation.

When installing the floor drain, it should be installed as low as possible, the location of the floor drain should be determined first, the floor tile is paved with slope to the floor drain, it is best to lay the whole brick at the floor drain position, and the floor drain is installed in the middle of a brick, and the diagonal line is opened, so that it is good to drain.

3. The connection between the floor drain and the sewer:

Generally, the drain interface of the floor drain can be inserted into the sewer pipe, and the four-proof floor drain is inserted into the sewer pipe.

Because this floor drain should be filled with water sealing core, so it can not be done too fine, if you add a circle inside, then the water sealing core must be made a little thinner, so it is made like this, only a small circle is stuck on the sewer pipe, and it does not affect the installation. If this kind of structure is a general residence, there is no problem, because after the ground is waterproof, when laying bricks, the floor drain core is aimed at the drain and smeared with cement, which is generally not a problem. But this kind of floor drain is not suitable for the frame floor, after installation, it will be unstable back and forth, there will be gaps, once the sewer under it is blocked, its water will flow into the floor, fortunately, such a structural floor slab is not much of a cavity.

When installing the floor drain, special attention should be paid to the bonding and sealing of the connection between the floor drain and the sewer pipe, and the installation should be tight, and the professional adhesive or glass glue can be used to seal the blessing.