How to install a router on a telecom fiber modem

After the telecom fiber is installed with the cat, the infinite router setup method:

1.Hardware connection: Use a network cable to connect any network port of the optical modem to the WLAN port of the wireless router, and if other computers in the LAN need to access the Internet through wire, you can connect the network of the computer to the LAN port of the wireless router through the network cable.

And press Enter, find "Network Settings" and "LAN Port Settings" in the page that opens, reset the IP address of the router to "Save", and then click "Save" to complete the IP address setting of the router.

3.On the page that opens, find "Network Settings" and "WAN Port Settings", set the "WAN Port Connection Type" of the router to "PPPoE" mode, then enter the Internet access and password, select the "Dial on Demand" mode, and click "Save" to complete the WAN settings of the router.

4.In the page that opens, find "DHCP Server" and "DHCP Service", select Enable DHCP Server, set the address pool start address to ", and set the address end address of the address pool to ", and click "Save" to complete the DHCP setting of the router.

5.Finally configure each device connected to the wireless router. You can configure the IP address acquisition method to be obtained automatically.

Hello, 1. Connect one end of the other network cable to the LAN of the second router, and connect the other end of this network cable to the computer. Set up the second router on the computer, click Network Parameters - WAN Port Settings - WAN Port Connection Type, and select the dynamic IP, and click Save.

2. Modify the IP address to [OK, click [Save], click Save, enter the browser, and enter to modify the second router. And that's it. Anhui Telecom*** is at your service.

1. Connect the network cable from the optical modem to the WAN port of the router, and then use the network cable to connect the computer to any LAN port of the wireless router.

2. Open the browser and enter the wireless router management address to enter, and enter the user name and password to enter.

3. After entering the management interface, click Next to start the setup wizard.

4. Select the PPPoE option in the Internet access mode, and click Next to continue.

5. Enter the broadband account number and password provided by the operator in the Internet account and Internet password. Click Next to continue.

6. Jump to the wireless wifi interface, set the wireless network name in the SSID, and set the wireless password of no less than 8 digits in the PSK password.

7. Click Restart, and the router is set successfully. After the reboot is complete, the computer only needs to be connected to the router LAN port or wireless network to access the Internet.

Do not connect the router to the modem first, and connect it to the computer separately. After setting, connect the modem to the computer.

The steps are as follows: 1. Connect the router to the computer separately, and connect any one of the LAN interfaces between the computer and the router with a network cable.

2. Enter the login interface of the router, enter the username and password to log in to the settings interface.

4. Connect the optical modem to the WAN interface of the router, as shown in the following figure. Finally, use the login and router settings interface to set the router to automatically obtain Internet access and set up wireless wifi.

If you need to set up, you can dial 10000 to ask the working orange high staff to help the user set up, if you are setting up a router, you need to enter the cheat key behind the router account name and password.

Regardless of the port from which the router receives the packet, it extracts the destination IP address and the source IP address of the packet: and then decides if, how, and which port to go to based on the routing table and routing policy.

1. Prepare two network cables, one end of which is connected to any LAN (1 2 3 4) interface on the modem router (primary router), and the other end is connected to the WAN interface of the secondary router;

2. On the setting interface of the secondary router, click "Network Parameters" - WAN port setting "- WAN port connection type" and select: dynamic IP (called "automatic acquisition" and "DHCP" on some routers) - click "Save".

3. In the setting interface of the secondary router, click "Network Parameters" - LAN Port Settings" - the "IP Address" on the right side is modified to: > click "Save", and then it will prompt you to restart the router.

Since the broadband is already connected to the modem, the new router does not need to set up a broadband connection, use a network cable to connect the modem to the LAN port of the router, and then set the wireless wifi of the router. The steps are as follows:

1. Insert the network cable into the LAN port of the telecom cat and the LAN port of the router;

2. Enter the router background login address in the browser to enter the router background management login page;

3. Click "Route Settings";

4. Click and select "DHCP Server" on the left.

5. Select "Off", here you must turn off the DHCP function of the router, because the modem has enabled the DHCP function, and multiple DHCP functions will cause conflicts, resulting in network instability.

6. Select "Wireless Settings" on the left and click to enter;

7. Turn on the wireless function, and then set the wireless name and password;

8. Finally, save it, and the router can be set up.

If the setting is incorrect, the telecom optical modem comes with its own dialing, and you do not need to set PPPOE dialing on the router, nor can you dial in this way.

The correct way is to connect the router to any LAN port of the modem. The router's settings interface only needs to set the wifi name and access password, and no other settings are required. After connecting, you can directly connect to the router with your mobile phone to access the Internet normally.

In addition, if the default access address of the router is the same as that of the telecom optical modem, you need to change it to it.

The cat has already dialed, so don't choose PPPoE dialing, just select the dynamic IP.

Because the cat has a collection of routes, the IP of the cat router is, then change the IP of the wireless router to set the wifi password.

Connect the LAN interface of your modem to the WAN interface of the router with a network cable, and then connect it to the computer with another network cable from the LAN interface of the router. Click **** to get more services, customer service 324 will answer for you.

Hello: You first connect the device as shown below.

Then in the case of not connecting the optical modem, set the LAN port setting of the wireless router, set the IP address to it, and then connect the optical modem, and then you can enter the wireless router, and then you can set other items on the router, enter the setup wizard interface, select PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, there will be an account number when opening broadband, you can fill it in.