How do you make a sculpture and what does a sculpture reachiever do?

Step 1: Clean up the residue on the surface of the sculpture model, spray it with washing powder and water after cleaning. Wait a few minutes for the laundry detergent to act as an isolating and release agent.

Step 2: Insert, insert is to separate the complex model, the principle of insert is to try to leave the seam behind the shape, can be as whole as possible. After the insert is completed, the mud sealing strip is completed.

Step 3: Cast the plaster, pour the first time with thin points, gradually dry the second and third times, and finally mix the brown silk and apply it to the surface of the model.

Step 4: Parting the mold, digging the mud, and separating the module according to the mud strip of the insert.

Step 5: Waxing, place the clean gypsum module in ventilation, and apply the bottom plate wax in a clean place, the purpose of which is also to play the role of demoulding.

Step 6: Clamp the mold, put the separated models together, and repair them with FRP at the joints.

Step 7: Color simulation, simulate different effects according to different material requirements.

The plaster sculpture was sprayed with soapy water twice on the clay sketch, or with dish soap water, and then the plaster began to be poured on it, which began to thin a little and gradually became sad. Add rice dumplings after two times. Finally, fix it with a stick!!

I am absolutely authentic and available. Because of my experience in sculpture, my practice is still very rich.

Apply a layer of release agent to the sculpture. Then apply a layer of mold silicone, and then use plastic sheets to make slit sheets. Then continue to apply the mold silicone until a satisfactory thickness is reached.

After it is dry, cut the bottom glue along the plastic sheet and pull out the original sculpture. A mold for the sculpture is complete.

It depends on what material you turn plaster, you can turn it yourself, and it is best to find a mold worker for other materials, I study sculpture, and I won't lie to you.

Spend money to do it, it's not that you can do it, it's professional technology.

Reproduced plaster mold, or silicone mold or fiberglass.

What is it made of?

The main tasks he is engaged in include:

1) Special tools for making sculptures;

2) Determine the return procedure of soft mold, hard mold, live mold and dead mold reproduction size;

3) Selecting, formulating, and using relevant materials to reproduce sculptures;

4) Deal with technical problems in the process of reproduction;

5) Large-scale sculpture reproduction and installation.

The following types of work are classified as occupations:

Carved tomb hungry plastic reproduction worker.

The main tasks he is engaged in include:

1) Special tools for making sculptures;

2) Determine the return procedure of soft mold, hard mold, live mold and dead mold reproduction size;

3) Selecting, formulating, and using relevant materials to reproduce sculptures;

4) Deal with technical problems in the process of reproduction;

5) Large-scale sculpture reproduction and installation.

The following types of work are classified as occupations:

Carved tomb hungry plastic reproduction worker.

The main tasks he is engaged in include:

1) Special tools for making sculptures;

2) Determine the return procedure of soft mold, hard mold, live mold and dead mold reproduction size;

3) Selecting, formulating, and using relevant materials to reproduce sculptures;

4) Deal with technical problems in the process of reproduction;

5) Large-scale sculpture reproduction and installation.

The following types of work are classified as occupations:

Carved tomb hungry plastic reproduction worker.

1. Divide your work into two parts with inserts, of course, depending on the specific shape of your work, there are also three to four parts.

2. Draw a layer of separator on the red clay, such as: laundry detergent water or soapy water.

3. The first layer of live gypsum is relatively thin, the second and third layers are slightly raised, pay attention to the degree of thinness, and you had better apply more to some deeper places.

4. When it is dry, the mold should be divided, and then the red mud inside should be taken out and the mold should be repaired.

5. Then brush the mold with the separator, and then close the mold with iron wire, and close it tightly.

6. Pour the gypsum slurry into the mold, pick up the mold and shake it, and repeat it, this step is very important to make it bubble.

7. After everything is done, wait until it is completely dry before using a tool to remove the plaster on the outside, taking care not to hurt the inner layer.

You can first use the real thing to make a first mold out, and then make a mold out of the mold silicone brush mold or inverted mold in it, and then you can pour the material directly into the mold for any sculpture and crafts you want to do, and you can mold it, and use HF-318 and HF-308 to turn the mold has its own advantages.

It depends on whether you can use only one mold for that sculpture. If you can, it's better to make a plaster mold for it first, and then put soapy water in it after the mold is dry, then grout, and then demold, reassemble and repair it.

The main tasks he is engaged in include:

1) Special tools for making sculptures;

2) Determine the return procedure of soft mold, hard mold, live mold and dead mold reproduction size;

3) Selecting, formulating, and using relevant materials to reproduce sculptures;

4) Deal with technical problems in the process of reproduction;

5) Large-scale sculpture reproduction and installation.

The following types of work are classified as occupations:

Carved tomb hungry plastic reproduction worker.

The main tasks he is engaged in include:

1) Special tools for making sculptures;

2) Determine the return procedure of soft mold, hard mold, live mold and dead mold reproduction size;

3) Selecting, formulating, and using relevant materials to reproduce sculptures;

4) Deal with technical problems in the process of reproduction;

5) Large-scale sculpture reproduction and installation.

The following types of work are classified as occupations:

Carved tomb hungry plastic reproduction worker.

The main tasks he is engaged in include:

1) Special tools for making sculptures;

2) Determine the return procedure of soft mold, hard mold, live mold and dead mold reproduction size;

3) Selecting, formulating, and using relevant materials to reproduce sculptures;

4) Deal with technical problems in the process of reproduction;

5) Large-scale sculpture reproduction and installation.

The following types of work are classified as occupations:

Carved tomb hungry plastic reproduction worker.