What s going on with the leak in the thermometer of the water heater?

If the inner tank is leaking, it cannot be repaired, and it can only be replaced with a new one, if the manufacturer has a commitment to the warranty period, it should be replaced, but a certificate is required.

Causes and treatment of electric water heater leakage:

1. a sealing ring.

Aging leads to water leakage. Solution: Replace the seal, which can be purchased at the hardware store.

2. The mixing valve is damaged and causes leakage. Solution: Replace the mixing valve or repair it again.

3. The oil tank is leaking due to damaged welded joints. Solution: Find a soldering tool and re-weld it.

4. The tank body is seriously rusted, and the rust penetrates the tank body, resulting in water leakage. Solution: Replace the magnesium strips.

5. a safety valve.

Back leakage, solution: replace the safety valve.

Causes and treatment methods of electric water heater leakage].

1. Water leakage caused by aging of the sealing ring. Solution: Replace the seal, which can be purchased at the hardware store.

2. Water leakage caused by damage to the mixing valve. Solution: Replace the mixing valve or repair it again.

3. The inner tank is damaged due to welding, resulting in water leakage. Solution: Find a soldering tool to re-weld it.

4. The inner tank is seriously rusted, and the rust penetrates the inner tank, resulting in water leakage. Solution: Replace the magnesium rod.

5. The safety valve is leaking, and the solution is to replace the safety valve.

Safety matters] 1. The power supply must have a reliable ground wire.

2. A fixed three-pin socket must be used, and the socket must be installed in a position where the shower water cannot be splashed.

3. Regularly (weekly) check the leakage protection switch on the power line of the fuselage, and prohibit the use of sockets with switches to keep the leakage protection plug working normally.

Fault 1: Water comes out of the small hole of the safety valve.

Cause Analysis and Repair:

When using the water heater, when the tap water pressure is too large, the steam pressure in the water heater will be greater than the pressure relief pressure of the safety valve, and then there will be a small amount of water, the thermostat will be damaged, and the water heater will always be in a heating state. To deal with this problem, you can install a pressure reducing valve in front of the water inlet of the water heater or leave the outlet open. The phenomenon of leakage in the small hole of the safety valve is a normal phenomenon.

Fault 2: Water heater mixing valve leakage.

Cause Analysis and Repair:

If the water heater mixing valve is leaking, then it is because the mixing valve is damaged, and when such a phenomenon occurs, we can only replace the mixing valve of the water heater if we need to repair it.

Fault 3: The magnetization thermostat of the water heater is leaking.

Cause Analysis and Repair:

The thermostat in the water heater It mainly plays a role in the water heater is to reduce the water flow of the nozzle, so that the water from the nozzle is more mixed, if the magnetic ring thermostat in the water heater is leaking, then it only needs to be replaced.

There are generally two possibilities for a water heater water pipe leak:

1. Water leakage at the water valve or connection of the water heater: When the water heater is installed, the water pipe interface is not installed well or the raw material belt is not wrapped enough, resulting in water leakage at the connection of the water valve.

2. Water pipe cracking and leakage: After the water pipe is used for a long time, the water pipe will also cause water pipe leakage due to aging, and individual water valves will also leak after a long time.

Of course, the possibility is not ruled out:

1. The connection between the water pipe and the joint, this depends on what kind of pipe is used, and the hot melt pipe is not well connected when hot melt and causes water leakage; The aluminum-plastic pipe is that the screws are not tightened or the sealing ring is damaged.

2. The connection between the joint and the water tank pipe is often caused by water leakage caused by the raw meal belt not being wrapped well.

3. The connection port between the water tank pipe and the water tank is commonly used in two ways: welded and silicone sealed.

If it is a welded type, then it is necessary to replace the water tank, if the warranty period has passed, you can find a master of argon arc welding, and get the insulation layer welded.

Dear, the reason for the leakage of the water heater thermometer: First of all, the sealing ring of the water heater thermometer is made clear by the blue socks, which will lead to water leakage due to the use of too long time and aging. Secondly, if the mixing valve of the water heater is broken, it will also cause the water to leak out of the position of the water heater's temperature gauge.

The third possibility is that the inner tank of the water heater has rusted due to the use of the inner tank for too long, and the water will leak out of the inner tank and flow out of the thermometer. The fourth possibility is that the inner tank of the water heater leaks out of the thermometer due to a leakage point at the place where it is welded. Wisdom of the Father.

Aging, hardening, or damage to the sealing ring or seepage valve can lead to water leakage. If you find that the water heater at home is leaking, you must unplug the power immediately, turn off the water inlet switch to ensure safety, and then contact the maintenance personnel for further inspection. The water heater water temperature meter leakage treatment method is as follows:

1. In case of water leakage, the power should be turned off first to prevent continuous water ingress and power connection. In general, the water leakage is due to a problem with the internal seal where the inner tank is combined with the heating pipe, in which case the sealing ring must be replaced to restore the water heater to normal. 2. It is also possible that the inner tank of the water heater will corrode and cause water leakage, and the water heater at this time will have no repair value, so you can only buy a new one.

3. The mixing valve of the water heater, the welding problem of the inner tank, the leakage of the safety valve, etc., will make it leak, which part of the water leakage can be replaced with new parts in time, if the welding is damaged, then the welder needs to re-weld it. 4. During the installation and use of the water heater, it is necessary to ensure that the power supply must have a reliable ground wire. Buy a three-pin socket and install it in a location where you can't splash when using water.

Regularly check the status of each switch to ensure that it can be used normally, and must not use the socket with the switch, so as to better maintain the plug of the leakage protection device can maintain a normal and stable state.

Summary. 1. Causes of water heater leakage.

1. The inner tank of the water heater is leaking.

2. The water heater interface is aging.

3. The safety valve is leaking.

Second, the solution.

1. Generally, it is not recommended to repair the inner tank if it leaks, because the inner tank enamel has been damaged, and it will not take long to leak after repair. From the direction of the dripping, such as a leak in the sealing ring or flange mouth, it may be solved by replacing the sealing ring. You can * manufacturer after-sales, see if the warranty period of your liner has passed, most manufacturers will replace the new machine during the warranty period, if the warranty period has passed, then you have to buy again.

Of course, you must report for repair of such a problem, and ask the manufacturer to send professional maintenance personnel to take a look.

Causes of water heater leakage.

2. The second type is relatively simple, if it is within the shelf life. You only need to replace the small parts of the interface, and the cost is within 50 yuan.

The thermometer of the electric water heater is leaking, what's going on? Broken? Is it easy to repair?

1. Water heater leakage Cause 1: Hot socks only water tank leakage. 2. The water heater interface is aging. 3. The safety valve is leaking.

2. Solution 1: It is not recommended to repair the water leakage of the inner tank, because the inner tank enamel has been damaged, and it will not take long to leak after repair. From the direction of the dripping, such as a leak in the sealing ring or flange mouth, it may be solved by replacing the sealing ring. You can * manufacturer after-sales, see if the warranty period of your liner has passed, most manufacturers will replace the new machine during the warranty period, if the warranty period has passed, then you have to buy again.

Of course, you must report for repair of such a problem, and ask the manufacturer to send professional maintenance personnel to take a look. The reason for water heater leakage 2, the second is relatively simple, if it is within the shelf life. You only need to change the small parts of the interface to make a good situation, and the cost is less than 50 yuan.

3. The third safety valve is leaking, and the third situation is that the safety valve is leaking, and you need to understand the work of the safety valve first. After installation, it is recommended that Liang Jinchun first turn on the faucet switch on the side of the hot water when the water is inlet, and turn it off when there is water at the hot water outlet, so that the air in the water heater can be drained clean. If the safety valve leaks water in the case of high temperature, it is normal, and there is no problem with the safety valve, because the inner pressure of the electric water heater is very high under high temperature, and part of the pressure must be discharged with the help of the safety valve, so that the water heater will not operate under high pressure rubber resistance, resulting in safety accidents.

If there is a water leak at low temperatures, the safety valve will have a problem with the operation, and it is recommended to replace it with a new safety valve.

The first reason for the leakage of the first type of thermometer must be the damage to the internal parts of the water heater, which in turn causes the water inside the water heater to leak outward through the damaged holes. So if the temperature gauge of the water heater has water seepage, several. Water leakage due to deterioration of the sealing ring.

Solution: Replace the seal, which can be purchased at the hardware store. Damage to the mixing valve leads to water leakage.

Solution: Replace the mixing valve or repair it again. The inner tank is damaged by the weld, resulting in water leakage.

Solution: Find a soldering tool to re-weld it. The inner tank is seriously rusted, and the rust penetrates the inner tank, resulting in leakage and water loss.

Solution: Replace the magnesium rod. You look at these.