If the sheet metal of the car is recessed a little, can it be sucked out directly with something wit

If the body is depressed and painted, it is recommended to paint sheet metal, about 300 to 500, but if there is no paint off and you are very concerned about the original paint, you can try the paint-free car dent repair technology, no need to destroy the original car paint for body concave repair, the principle is actually very simple, it is based on optics and mechanics, and the use of the lever principle to slowly restore the pits of different depths to the original appearance, look at the following picture You can see it at a glance.

Similar to the one in the picture, it is generally about 300 yuan.

<> the picture below is the repair effect of our sharkskin car dent repair direct store**, the first one**The black border area on the left is the appearance of the original painted body, and the right is the appearance of the repaired body, how can you feel the specific effect, but after all, there are so many stores in the country that the car dent repair can not be generalized, so I suggest that you still go to the regular brand store to repair, so that the technical level will be *** and** fixed, unlike small shops that will only shout prices all over the sky.

No. Explanation:

Sheet metal worker is to erase the paint on the surface of the car, and then weld it with argon arc welding and then gently pull it out, if the paint is not erased, there is no way to irgon arc welding the paint on the surface of the car body is insulated and cannot be welded.

Features: sheet metal has the characteristics of light weight, high strength, electrical conductivity, low cost, good mass production performance, etc., with the application of sheet metal is more and more extensive, the design of sheet metal parts has become a very important part of the product development process, mechanical engineers must be proficient in the design skills of sheet metal parts, so that the design of sheet metal not only meets the requirements of product function and appearance, but also can make the stamping die manufacturing simple and low cost.

Car sheet metal dents can be sucked out without damaging the original paint finish, but it takes a long time.

The specific steps are as follows:

Step 1: Suck with a straw first, then pick slowly with a hook.

Step 2: Slowly beat with a rubber hammer, then sand with fine sandpaper, and then polish with a polisher, and finish.

In the process of using a car, it is inevitable that there will be stumbling, so how can this situation be minimized? Let's take a look:

1.Be sure to make it a habit to observe your surroundings before driving.

Sometimes, some children or small animals will play around, and it will be difficult to find them. If you take a few seconds to look at it again, you might avoid something.

2.Turn on your turn signals and look in your rearview mirror before changing lanes.

The turn signal is to remind other vehicles, and you can see the vehicle behind you by looking at the rearview mirror, which can ensure the safety of driving ulcer cracks.

3.Stay away from the trolley. If you are close to a large car, the danger factor of the big car will also increase. Staying away from big cars is the wisest choice.

4.Keep an appropriate distance between cars so that there is a certain safe distance. In case of emergency, avoid rear-end collisions, resulting in loss of property and life.

Millions of car purchase subsidies.

The sheet metal depression can be sucked out, and it does not slip and damage the original paint surface, but it takes a long time.

The specific steps are as follows:

Step 1: Suck with a suction cup first, then pick slowly with a hook.

The second step is to knock slowly with a rubber hammer, and then polish it with fine sandpaper and polishing machine, and then finish it.

In the process of using the car, it is inevitable that there will be bumps and bumps, so how can we minimize this situation, let's find out:

1. Observe the surrounding environment before driving, and be sure to develop this habit.

Sometimes, children or animals will play around, and it's hard to spot, so if you take a few seconds to look at it, you might be able to avoid something from happening.

2. Before changing lanes, you should turn your turn signal in advance and look at the rearview mirror.

The turn signal is to prompt other vehicles, and you can see the vehicles behind you by looking at the rearview mirror, which can ensure the safety of driving.

3. Stay away from the car, and the car is closer, the risk factor of the car will also increase, away from the car is the wisest choice.

4. It is necessary to maintain a suitable distance between vehicles, so as to have a certain safety distance, and in the event of an emergency, avoid rear-end collision and loss of property and life.

The car sheet metal depression can be sucked out without damaging the original paint surface, but for a long time.

The specific steps are as follows:

Step 1: Suck with a suction cup first, and then pick slowly with a hook.

Step 2: Slowly tap with a rubber hammer, then sand with fine sandpaper, polish with a polisher, polish.

In the process of using the car, it is inevitable to stumble, so how can this situation be minimized? Let's take a look:

1.Be sure to make it a habit to observe your surroundings before driving.

Sometimes there are some children or small animals playing around, and it is difficult to spot. If you take a few seconds to look at it again, you might avoid something.

2.Turn on the turn signal in advance before changing lanes and look in the rearview mirror.

The turn signal is to remind other vehicles, and you can see the vehicles behind you by looking at the rearview mirror, which can ensure driving safety.

3.Stay away from the trolley. If you are close to the cart, the risk factor of the cart will also increase. Staying away from big cars is the wisest choice.

4.Keep an appropriate distance between vehicles so that there is a certain safe distance. In case of emergency, avoid rear-end collisions, resulting in loss of property and life.

Now the car is our daily travel tool, and there will be some problems in the process of use, such as: how to suck out the car when it goes in. Then I will introduce it to you below, I hope you can help.

Some car repair shops have special equipment. Before sucking, blanch it with boiling water, then place the suction cup in a concave place, and then use the machine to suck the air in the dish. This increases the suction power and then pulls it out forcefully.

If there are dents on the front and rear bumpers, it is easy to suck the dents out with the above method.

If there are dents in the metal part of the body, the above methods may be successful in sucking out, but not necessarily successful.

If it can't be sucked out, then riders need professional sheet metal repair.

When repairing sheet metal, the technician will first fix the dents, then polish the paint, then scrape the putty, polish the putty, and finally repaint.

When advocating sheet metal repair, be sure to go to a professional organization, and then find a professional.

The putty used in some small shops is not of good quality, and the painter's skills are also majority. After repairs at such shops, the putty may crack after a period of use, affecting the peeling of the paint and rusting of the metal parts.

Some roadside shops may not be accurate in color matching, and there will be color differences after painting, which is very beautiful.

Riders are encouraged to go to professional institutions or 4S shops immediately when repairing or painting sheet metal, and riders must not go to some roadside shops for cheapness.

If a certain part of the body is dented, you need to go to a professional sheet metal maintenance agency to suck it out with a professional tool, and the owner can't suck it out by himself.

If the body is dented and deformed, it can be restored to its original state by sheet metal repair, but before sheet metal repair, be sure to choose a professional shop.

After the car sheet metal is repaired, it needs to be repainted.

The paint surface of the body is composed of four layers, from the inside to the outside, the electrophoresis layer, the middle coating, the color paint layer, and the clear coat layer.

After the entire body is assembled, the robot will soak the entire body in an electric swimming pool, so that an electrophoretic layer will form on the body.

The main function of the electrophoretic layer is to prevent rust.

After the electrophoretic layer is formed on the surface of the body, the robot will spray an intermediate coating, which is also used to prevent rust and improve the ability to bond with the next layer of paint.

After spraying the intermediate coat, the robot will spray the color paint layer, which mainly plays an aesthetic role. The various body colors we usually see are presented through the paint layer.

The outermost layer of paint is the varnish layer, which plays the role of protecting the paint layer and can also improve the gloss of the body paint surface.

Usually small scratches are left on the varnish layer and can be removed by simple sanding.

Millions of car purchase subsidies.