How much does it cost to scratch the vehicle, sheet metal and spray paint, and how long does it take

Hello, this sheet metal spray paint** needs to depend on the degree of your injury and the area to calculate, if you are convenient, it is best to upload a** normal spray is according to a piece of area, such as a door, **a bumper** normal area is about 300 yuan, if it is a high-end car in 600 yuan or even higher.

Hello, this depends on whether your severity is serious, under normal circumstances, sheet metal painting is two or three days to pick up the car, because this sheet metal painting needs to be baked with a lamp, as for the ** general car, a face is about five hundred.

The sheet metal spray paint treatment 4S shop is 400 yuan for one side of the paint, and the outside repair shop is about 200 yuan for one side of the paint.

It's hard to say, it depends on the severity and area of the scratch. Normally, if you are single-sided, the sheet metal is painted on the outside, and it will be about 400 on the outside, and about 700 if you go to 4s.

Hello, this sheet metal painting is based on the area of the vehicle, and it generally takes about 2-3 days.

Hello, if it is a slight scratch and very little sheet metal, a normal day is enough, take the car the next day, and then polish it, and the normal **200 one side looks.

Hello, you need to look at the degree of scratches of the car, the workload of sheet metal to calculate the time, generally two sides of the sheet metal painting takes two days, the general repair shop ** in about 600.

Good afternoon, this depends on the severity, it is best to upload** to see, ranging from 200-2000**, it generally takes a day or even longer, and you also need to see what car is repaired in what place one ** for reference only.

Hello, this depends on the degree of damage to your Huasheng, if the damage is more serious, it is recommended that you go to the repair shop directly sheet metal painting on it, the cost is generally about 400 per side.

Hello, this needs to look at the damaged area specifically, if it is not serious, it can be done in one day.

Hello, is there a **?,It's best to upload** for you to confirm before I can give you a clear answer.。

This situation requires the entire door to be repainted to deal with the general repair shop**350, 4S** around 500.

Minor scratches can be smeared with scratch wax or toothpaste, and then the scratches can be removed by wiping with a dry towel, and if they cannot be removed directly, polish them first. If the paint is broken, you can simply use a paint pen to repair it or cover it with a sticker, and the scar is in the bumper position, so it's okay if you don't deal with it.

Precautions. If you need sheet metal, you need to add extra money to deal with it, because the sheet metal processing variables are large, and there is no way to give a realistic price, because 50 yuan for small problems can be solved, and hundreds of dollars for big problems. Of course, the advice of the woodpecker master here is that the sheet metal on one side is ordinary depression and scratching, and the psychological expectation expenditure is 150 yuan.

Hello, it depends on the degree of damage to your car door, if you need sheet metal, it will be a little higher, about 600 yuan, if you only need to repaint, it will be a little lower, about** around 400 yuan.

Hello, happy to answer your questions.

Hello, I'm helping you sort out the answers to your questions, please wait a moment Ask about how much does it cost to spray paint and sheet metal.

For example, the price of about 100,000 yuan for this car to spray a surface needs more than 700 yuan in a 4S shop, and more than 300 yuan in an outside repair shop.

Question: I'll send it to you to see how much you'll need.

Yes, ask questions.

That's how it was recessed.

The cost of working hours in the repair shop outside includes the cost of materials, up to about 500 yuan.

Question: Okay, thank you.

You're welcome to ask.

How long will it take?

The whole door painting and sheet metal repair can be done for 350 yuan, generally as long as the sheet metal is painted, the entire door should be painted, so that there is no color difference.

Because the paint is different from the model, and the degree of door damage is different, it is more difficult to determine the repair, and the sheet metal painting is estimated to be about 500.

The car door is generally fat, the menstrual period is good, how much does it cost, this depends on the area of the flower scale, under normal circumstances, the door is scratched, and the paint is generally bound, and it is more expensive to spray it.

<> "Car scratches are encountered by many car owners. So, what to do if the car is scraped off by paint? Most of them will choose sheet metal painting, so how much is car sheet metal? I'm going to talk to you about this topic today.

Minor scratches can be applied with scratch wax or toothpaste, then wiped off with a dry towel.

If it cannot be removed directly, polishing should be done first. If the paint is broken, it can be simply covered with touch-up pens or stickers. If there are scratches on the bumper, it doesn't matter if you don't have to deal with it.

If the stove branch fruit is only simply spray painted, a paint surface is 200 400 yuan. According to different places, if you are a novice, then go to the roadside repair shop for 100 yuan almost to imitate the excitement, anyway, there will be scratches in a few days, and you don't have to care about the quality of this 100 yuan. If you go to a 4S store, the lacquer usually starts at 300 yuan.

If it's a luxury car, it's even more expensive.

In addition, if you need sheet metal, you also need to add extra money to deal with it, because the sheet metal processing variables are very large, which cannot give a specific **, because small problems can be solved with 50 yuan, and big problems may be hundreds of dollars. Of course, the personal suggestion is that the psychological expectation of spending 150 yuan is 150 yuan for a surface of sheet metal and ordinary depression and scratching.

Now speaking of paint restoration. Generally speaking, a door, a bonnet, and a unique surface are painted. The paint ** of some stores is uniform, no matter which part it is, it is 300 yuan.

However, more stores make some distinctions. The roof, lid, and front and rear bumpers are comparatively more expensive than four-sided doors and fenders, ranging from about 10% to 35%, depending on the actual situation and type of paint.

There are also differences in the built environment. Whether there is a paint room affects the hardness of the paint, and the result is directly reflected in the life of the paint.

If you spray pearl paint and paint room paint, the ** of a car door may be 350 yuan.

If you spray metallic paint and paint room paint, the ** of a door is about 280 yuan.

If you only use ordinary paint and paint room paint, the ** of a single door may be 180 yuan.

This **is the average medium-sized car repair shop**. This is just the ** of the companies that have been served before. It does not represent ** across the country, nor is it equal to ** of roadside repair shops and 4S shops.

Summary: Here, I suggest that you only set a psychological expectation**, just scratch the spray paint, and it is expected to cost 280 yuan. If sheet metal fabrication is required, an estimated cost of $150 is added.

The ** given here is relatively conservative, and you can definitely find a cheaper one than this **.

The door is scraped with sheet metal spray paint, if it is just a very ordinary family car, if such a painting repair is carried out in an outside auto repair shop, it is about two or three hundred.

A door sheet metal painting is about 350 to 800 yuan, and the maintenance of the outside auto repair shop is quite different from that of the 4S shop.

Summary. Hello, I have seen your inquiry, please wait for a moment and answer it for you immediately.

The door is scratched, and it costs to do a good job of sheet metal spray painting.

Hello, I have seen your inquiry, please wait for a moment and answer it for you immediately.

Hello, if you don't need a large area of sheet metal, a slight sheet metal plus painting, a door ** is about 300 to 400 can be repaired.

Is the slight depression of the front door also this**.

That's right, you don't need to add money for the slight ones.

It is when the speed is low, and the rear car slams the front door with the accelerator. Do you mean the entire front door sheet metal painting? ** of the 4S shop?

No, it's the outside repair shop's **, in this case, the outside repair shop 400 is enough, and the 4s is more expensive.

How much does that 4s cost?

Sub-brand, probably less than 1,000 yuan, you can call ** to consult local after-sales.

Rental car, car rental company has repair place. But I'm fully responsible, and I guess I'll have to pay for it myself. Is there anything to be aware of?

They designate a repair shop, if it is not high, let them go out of the formalities after repairing, and the problem has nothing to do with you later.

Okay, thank you, it's the first time I've sued my brother for an accident. Is it appropriate to find a roadside repair by yourself or go to the envy and disturbance ming 4S store they cooperated? The BAIC EU260 rented by the company's Li Jing is not a valuable car.

You can ask**, if the roadside is repaired, it will take about two days to Changze, and if this is the rent in these two days, it will not be suitable for the calendar. It's better to go to their repair shop to fix it.

The rent is fine, the main thing is that it is cheap [eat whales] I estimate that I have to pay for it myself.

Well, then just go outside to repair it, it's cheaper to repair it outside.

If I can help you, please give me a thumbs up Thank you!

Driving is a bit bumpy. If it weren't for the Great Depression, many car owners would be reluctant to do sheet metal, so how much sheet metal is the car? Real cars are really expensive.

No wonder old drivers don't recommend brushing sheet metal as long as they are not very dented, because a small point costs hundreds of dollars more, and the pimples are all meat.

1. Automobile sheet metal ** table.

Cars** will vary in each region. This is a list of cars for each region. It can be found that the ** of each party will be different, which is determined by the degree of damage and the difficulty of construction.

In this form, the sheet metal cost and the painting cost are separated, but they are often done at the same time, and they are called ].

Because we have dents after a collision, the paint will come off, and sheet metal is just a car dent repair technology, so we still need paint. In order to restore the car to its pre-collision state, it is necessary to restore its color and shine to its original state as much as possible (it can only be similar, not restored). So we can see that sheet metal is quite cheap, about 100,000 yuan for a car is only about 100 yuan, but in fact, it takes about 500 yuan to do sheet metal painting, which is only a part.

However, these are the best travel trips in general 4S shops, so many car owners say on the Internet that they only need about 300 yuan to go to the roadside repair shop, which is certain that it is cheaper. But if you don't go to the 4S shop where the sheet metal is being dismantled, it's best to find a place with acquaintances, otherwise the sheet metal will be cheated, and the consequences will be very serious, because some repair shops cut corners, which will lead to serious consequences.

Second, the consequences of not doing a good job in automobile sheet metal.

1.Automotive If the heating process is also applied in the sheet metal process, the metal material will anneal, and the strength and hardness of the metal will decrease. In the event of another collision, the protection of the occupants of the vehicle may not be sufficient.

2.Because the metal is sheet metal, if the repair is not professional enough, it is easy to appear uneven, and cracks, dents and other phenomena will occur after a long time, which will affect the appearance of the car.

3.Whether it is sheet metal or Qingpei whole car painting, although it looks like the production setting has been restored, it will actually have an impact on the value retention rate of the car, because your car is no longer the original paint, and no matter how good the paint is, it will not achieve the original effect.

Millions of car purchase subsidies.

If a car of about 100,000 yuan costs sheet metal painting, how much does it cost?

Side of the body. Front and rear door sheet metal spray paint 500 yuan.

Front and rear fenders sheet metal painting** 400 yuan.

Bottom edge sheet metal spray paint** 200 yuan.

The upper part of the car. Roof sheet metal painting** 800 yuan.

Front cover plate sheet metal painting** 800 yuan.

Trunk lid sheet metal spray paint** 500 yuan.

Car front and rear bars.

Front and rear bumper sheet metal spray paint** 400 yuan.

The above ** are all including sheet metal repair and painting, the expensive part of the car painting is the roof and engine cover, because these two areas are large, and the painting is more troublesome than other parts.

Note: The above is the ** of the 4S store, but the ** of the general 4S store. Roadside shops and repair shops are relatively cheaper, about 30%-50% cheaper than 4S shops.

Sheet metal is a comprehensive cold working process for metal sheets (usually below 6mm), including shearing, punching, cutting, compounding, folding, riveting, splicing, forming (such as automobile body), etc.;

Painting is a work in which the spray gun is dispersed into uniform and fine droplets with the help of air pressure and applied to the surface of the coated object.

2. The order of the two in the workflow is different.

Taking car restoration as an example, the sheet metal is in the front and the painting is in the back, and the order of the two cannot be reversed.

3. The technology to be mastered by the two is different.

Sheet metal technology needs to master the rational use of materials, size and length matching, scrap material assembly, row wrench nesting, straight line, arc shearing methods, learn the convex and concave, edge warping and patting correction of sheet metal, as well as the commonly used sheet metal, bending, edge closing, edge laying, crimping, bite and correction methods and other complex technologies and processes;