What to do if IWC specializes in repairing watches when it gets wet, IWC watch repair points

How to deal with the watch stopped by magnetization:

Holding the watch slowly close to the hair dryer, note that you should always keep it in one direction, and then move away slowly, generally to eliminate the lighter magnetism.

Using the degausser, press the red button to open it first, face the watch upwards, keep a certain distance from the demagnetizer, (the mobile phone watch cannot be directly attached to the demagnetizer) pass through the left and right (or from right and left) at a constant speed.

For some watches, it comes with an anti-magnetic device, if there is magnetism, then you should go to a professional watch repair shop to ask the maintenance personnel to replace the anti-magnetic device and demagnetize.

Dust that enters the dial of a watch is usually due to gradual infiltration during prolonged wear. If only fine dust is entered, there is no need to clean it without affecting the appearance and use. However, if there is a certain length of dust such as hair or acrylic fibers that enters the watch dial, it is necessary to pay attention to it, because such dust is very likely to stop the operation of the watch.

In this way, we have to go to the regular watch repair shop in time to clean up, and after cleaning, we must consider the problem of re-sealing.

If a mechanical watch is damp, the best way is to go to a watch repair shop for a full inspection, which can prevent serious rust on the watch at a lower cost. If the movement is corroded, the watch will be scrapped and the loss will be great, so it is important to prevent accidents.

Daily repair methods for water ingress in the watch:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe. (It is not recommended to use the above methods to deal with it, it is recommended to go to the after-sales center for maintenance).

Watch maintenance and repair can refer to the service center of 702] Joy City Office Building, Xidan District, Xicheng District, Beijing to provide IWC watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of parts, and strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

When an ordinary mechanical watch is damp, you can press it on the watch with dry cotton, and then bake it with a 40-watt light bulb for 5 minutes, and all the moisture in the watch can be evaporated. Water in the watch is a more serious thing, especially some high-end mechanical watches, if not repaired in time, then the water will make the steel parts in the watch movement appear embroidery, tiny clock parts usually need to be replaced once rusty, the future repair cost will be very large, to know that the damage to the watch is "catastrophic". In addition to movement parts, long-term exposure to moisture can also cause discoloration, blistering and rust on the dial and hands of the watch.

If there is a problem with the watch, it is recommended to go to the regular after-sales service for maintenance, not only the technician is more professional, the instrument is also more precise, and the **transparent is not messy**. There is a very good after-sales service near Wanling Hui in Tianhe District, so I will go to see it when I have time. My personal advice is to pass as soon as possible, otherwise the longer the time, the greater the problem with the watch, and the greater the economic loss.

The main thing is that it is still more troublesome, and the repair time will become longer.

If the mechanical watch is damp, you can press it on the watch with dry cotton, and then bake it with a 40-watt light bulb for 5 minutes, and all the moisture in the watch can be evaporated. However, if there is a water stain on the inside of the glass or on the dial, it must be treated by a professional institution.

Four Seasons" Zeng Li, Wu Xiaotian, Li Yongchang, Episode 27 to 52 Ending Song Broadcast Information, Broadcast Platform, Broadcast Date, Broadcast Column.

IWC watch repair points include IWC after-sales Jinan Jingshi store, IWC after-sales Chengdu Jingshi store, Shanghai Jingshi store, Beijing Xidan Jingshi store, Shanghai Ganghui store, etc.

1. Wanguo after-sales Jinan Jingshi store.

The service of Wanguo after-sales Jinan Jingshi store is 4001552501; The address of the outlet is Room 1005, 10th Floor, Block B, Qilu International Building, No. 180, Quancheng Road, Lixia District, Jinan City.

2. Wanguo after-sales Chengdu Jingshi store.

The service of Wanguo after-sales Chengdu Jingshi store is 4001552501; The address of the outlet is Baiyang Building Watch Repair Center, No. 18, Dongyu Street, Jinjiang District, Chengdu.

3. Bituan Shanghai Jingshi store.

The service of Shanghai Jingshi store is 4001552501; The address of the outlet is Room 918, 9th Floor, Shanghai Landmark Plaza, No. 409 Nanjing East Road, Huangpu District, Shanghai.

4. Beijing Xidan Jingshi store.

The service of Beijing Xidan Jingshi Store is 4001552501; The site of the wide section of the network is Room 702, 7th Floor, Xidan Joy City Office Building, No. 131, Xidan North Street, Xicheng District, Beijing.

5. Shanghai Ganghui store.

The service of Shanghai Ganghui store is 4001552501; The address of the outlet is Room 709, 7th Floor, Block 1, Shenshuyu Center, Ganghui Hang Lung Plaza, No. 1 Hongqiao Road, Xujiahui, Shanghai.

The above content reference: IWC-Wanguo after-sales Jinan Jingshi store.

What to do if the watch gets into water, don't worry, I'll tell you a little trick.

There are generally three ways to enter the water in the watch, the watch is worn backwards, the desiccant is removed and the lamp is baked to remove the water, it may seem that the effect is not bad, but the fact is not satisfactory, those methods can only remove the water stains on the surface, and the water stains that penetrate into the movement can not be removed with certainty, and it is not too much to treat those small watches, but for those famous watches, if this method is adopted, I am afraid that it will be regretted in the future. If this method can be handled completely, then the repairer will not have to eat. It is recommended to send it to a professional repair point if it enters the water.

1. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor.

2. Do not bake the watch directly near the fire, so as not to deform the watch by heating.

3. You can also wear the surface face inward and the bottom shell outward, and wear it on the wrist, and the water vapor can be eliminated after two hours.

4. If the water ingress is serious, it is best to send it to the watch shop immediately to wipe the oil and remove the moisture of the movement to avoid rust of the parts.

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

International Trade Store: Room 1102, Block D, Bloomage International Center, No. 6A, Jianguomenwai Street, Chaoyang District, Beijing.

If the watch is flooded, it can only be sent to the repair station for repair. After opening the watch, removing the water vapor in the watch, and lubricating the rotating part with oil, it can be used normally.

You can try to store it in a rice tank, which can effectively absorb water in a dry environment; If the effect is not obvious, it is recommended to go to a repair shop for repair.

What should I do if my watch falls into water? Watch water ingress treatment.

1) There is fog in the glass of the watch, and there may be some times and sometimes not, especially when the temperature difference is large.

2) There are water droplets solidified in the watch glass.

3) A large number of water droplets can be seen on the glass and dial of the watch.

There are also several properties of the water into which the watch is ingressive

1) Mineral water or distilled water.

2) Rainwater or tap water.

3) Beverages or beer (4) seawater (5) cosmetic products or chemical tests or potions distilled water are always in the best condition, and seawater is more corrosive, let alone chemical tests. The most important thing to do after the watch is flooded is to send the watch to the watch repair shop for water removal measures, and if the water is serious, it is necessary to wash the oil. If it is not repaired out of time, then the water will expose the steel parts in the watch movement, and the subtle clock parts will be rusted and generally need to be changed, and the cost of repair in the future will be very large, and the consequences of the watch after water are generally very serious.

In addition to the movement parts, prolonged exposure to water vapor can also cause the dial and scale hands of the watch to change color, blister and rust.

Then you first go to the place where the watch is repaired, the watch is not an electronic product, as long as the technology is good, it can still be repaired.

There are generally three ways to enter the water in the watch, the watch is worn backwards, the desiccant is removed and the lamp is baked to remove the water, it may seem that the effect is not bad, but the fact is not satisfactory, those methods can only remove the water stains on the surface, and the water stains that penetrate into the movement can not be removed with certainty, and it is not too much to treat those small watches, but for those famous watches, if this method is adopted, I am afraid that it will be regretted in the future. If this method can be handled completely, then the repairer will not have to eat. It is recommended to send it to a professional repair point if it enters the water.

Shanghai Watch Service Center is located in Room 1003, 10th Floor, Hongyi International Plaza, No. 299 Nanjing East Road, Huangpu District, Shanghai.

1. Use silica gel to dry the granules. If water enters the case, a granular substance called silicone can be used to put the watch in an airtight container with the water that has accumulated water, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and the accuracy and longevity of the watch will not be compromised in any way.

The silica gel, which has been absorbed many times, can be dried at 120 degrees for several hours, has a renewable water absorption capacity, and can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes, which will eliminate the moisture. Be sure not to bake the watch mask directly near the fire to prevent the watch from being deformed by heat.

3. Wear the watch backwards. You can also wear the mask with the cover facing inward and the bottom shell facing outward, and wear it on the wrist, and the moisture will be eliminated after two hours. If the water ingress is severe.

4. Send it to the watch shop to wipe the oil. None of the above three methods can remove water vapor, and it should be sent to a repair shop immediately to wipe the oil to remove moisture from the movement and prevent rust on the parts.

5Dry with a hair dryer, the temperature should not be too high, and the wind will be mild until the moisture on the glass is not visible.

IWC Watch water maintenance location can go to Room 1502, Block A, Office Building, Victoria Plaza, No. 103, Tiyu West Road, Tianhe District, Guangzhou, and there are several properties of the water in the watch: mineral water or distilled water, rainwater or tap water, beverages or beer, seawater, cosmetic products or chemical test drugs or potions. Today's watches are basically waterproof watches, and the waterproof standard is 30 meters, or 3 atmospheres of pressure.

This waterproof standard is called "survival waterproof", which can only prevent accidental splashing or accidental spills on the outside, and must not be worn to dive and prick.