What are the precautions for installing elevators

When installing the elevator, it is necessary to pay attention to the design of the elevator, the load-bearing installation of the elevator, the destruction of the housing structure and the space utilization rate and other factors. The recommended home elevator is a product of Asia Fuji Changlin Elevator Company. The brand has been engaged in the elevator industry for more than 30 years, and has stood at the highest point of the industry at the beginning of its establishment

The products are personalized and diverse.

1. Shaft location and space: The shaft location space determines the size of the elevator and the door. It is a good solution to install an elevator in the middle of the staircase and combine it with the staircase.

1. The middle of the stairs, the corner of the wall, and the plug-in can be used, and it is better to not block the passage in the center.

2. Use the width of the door to push back the width of the hoistway, and use the height of the top floor to push back the height of the car.

3. The load capacity is recommended for 3-4 people, 225-320kg, and the size of the car is square meters. The relative load capacity of the area can be larger than that of the passenger elevator, which increases the comfort.

In fact, it should be noted that they all know to the elevator company that the installation of elevators is not as big as you imagined, engineering, on the contrary, you need to have a certain procedure to get that approval, if you are an old community, that kind of testing and evaluation, it will take some time, I have had such a case, so it is clear that anyway, your early procedures are the most important, and the later project is nothing.

Since the elevator installation is a kind of high-altitude operation, in order to facilitate the installation personnel to carry out construction operations in the hoistway, the general contractor should cooperate with the needs of the elevator installation, build scaffolding in the appropriate part, the hoistway should be dedicated to the elevator, and the hoistway shall not be installed with equipment and cables unrelated to the elevator.

There should be good anti-seepage and anti-leakage protection in the pit, there shall be no water accumulation in the pit, and each floor should have a horizontal datum mark, and the safety protection of the elevator mouth should be done before the elevator is installed.

According to the location of the machine room, the elevator of the machine room at the top of the hoistway (upper machine room), the elevator of the machine room next to the bottom of the hoistway, and the elevator of the machine room inside the hoistway (without machine room).

(1) The civil structure and layout of the machine room and the hoistway must meet the requirements of the elevator civil layout drawing.

2) The main power switch must comply with the following regulations:

a. The main power switch should be able to cut off the maximum current of the elevator under normal use.

b. The elevator switch should be easily accessible from the entrance of the machine room.

3) The hoistway must comply with the following requirements:

a. When there is a space that can be reached by personnel under the bottom surface of the pit, and there is no safety gear device on the counterweight (or counterweight), the counterweight buffer must be installed (or the lower edge of the counterweight operation area must be extended) to the solid pile pier on the solid ground.

b. Before the elevator is installed, all the reserved holes of the landing doors must be equipped with a safety protection enclosure with a height not less than that, and should ensure sufficient strength.

c. When the distance between the adjacent two layers of door sill is greater than 11m, the hoistway safety door must be set up in the meantime, and the hoistway safety door is strictly forbidden to open to the hoistway, and the elevator can only run when the safety door is closed.

4) Requirements for the machine room before handing over to the elevator contractor:

a. There should be fixed electrical lighting in the computer room, and the illumination on the floor surface should not be less than 200lx.

b. The computer room should be ventilated, and the stale air extracted from other parts of the building should not be discharged into the computer room.

c. Elevator assembly personnel should be able to easily enter the machine room or pulley room, without the need for temporary use of other auxiliary facilities.

d. During the construction process, if it is necessary to overhaul the opening position of the trap door, in order to prevent personnel from falling, guardrails should be set around it.

e. There should be good anti-seepage and anti-leakage protection in the computer room.

5) According to the requirements of the elevator contractor, provide the passage and handling space required for the equipment to enter the site.

6) Since the elevator installation is a kind of high-altitude work, in order to facilitate the installation personnel to carry out construction operations in the shaft, the general contractor should cooperate with the needs of elevator installation and build scaffolding in suitable parts.

7) The hoistway should be dedicated to the elevator, and the hoistway shall not be equipped with equipment and cables unrelated to the elevator.

8) There should be good anti-seepage and anti-leakage protection in the pit, and there should be no water accumulation in the pit.

9) Each floor should have a horizontal datum mark.

10) Before the elevator is installed, the safety protection of the elevator mouth should be done.

11) Due to the large amount of elevators in this project, the general contractor should cooperate with the finished product protection of the elevator in the part where the elevator is installed.

The elevator belongs to special equipment, which is supervised by the Special Equipment Department of the Technical Supervision Bureau, and there are strict regulations.

Pay attention to the safety of construction personnel in the hoistway, and whether the installed parts are firm.

1. The elevator installation site must be supervised by technical and safety personnel;

2. Before the elevator is installed, the staff should carefully inspect the tools and accessories, and replace the unqualified ones immediately to ensure normal use;

3. The elevator installation area is set up with a cordon, with obvious signs, and there must be a special person to supervise, and it is strictly forbidden for idle personnel to enter and exit the site during the installation;

4. During the installation process of the elevator, the installation staff is not allowed to throw items downward at high altitude;

5. During the elevator installation process, all staff must wear safety helmets, high-altitude personnel must wear non-slip shoes, and safety belts must be fastened and toolkits must be hung for high-altitude work;

6. During the installation of the room elevator, pay attention to the obstacles around the building, if there are obstacles, they must be removed before they can be operated to prevent accidents;

7. In the elevator installation process, the next installation process can only be carried out after the completion of each process after being inspected and approved by a special person;

8. During the installation of the elevator, the load of the cage is not allowed to exceed the rated installation capacity.

9. After the elevator installation is completed, the various mechanisms of the construction lifting and respecting machine should be carefully checked, whether each part should be in good condition, and the problems should be dealt with in time;

10. In strict accordance with the installation method of the product instruction manual, the various emergency situations in the process of outdoor elevator installation are correctly handled.

In general, there are many aspects that need to be paid attention to in the process of installing elevators, and it is important to remember that you should not take it lightly. At the same time, the working place must have sufficient lighting, the entire workplace must always be kept clean, all kinds of materials must be prepared, and attention must be concentrated during work to avoid unnecessary trouble.

1. Position and space of the shaft: The location and space of the shaft determine the size of the elevator and the door. It is a good solution to install an elevator in the middle of the staircase and combine it with the staircase.

1 In the middle of the stairs, Brother Hu's wall pants are fine, and the plug-in can be, and it is better to not block the passage in the center.

2. Use the width of the door to push back the width of the hoistway, and use the height of the top floor to push back the height of the car.

3. The load capacity is recommended for 3-4 people, 225-320kg, and the size of the car is square meters. The relative load capacity of the area can be larger than that of the passenger elevator, which increases the comfort.

1. When installing the elevator, there must be professionals on the site to supervise, and the installation area must be cordoned, and obvious signs must be placed in front of the elevator to avoid others entering and exiting the elevator. Before installing the elevator, it is necessary to prepare the required tools, and check the parts, and replace them in time once the parts are unqualified.

2. When installing the elevator, all construction personnel must obey the command of the commander, and a special person must be assigned to check the power supply. During the installation process, the construction personnel must wear safety helmets, wear non-slip shoes, fasten safety belts, and bring tool kits to avoid safety accidents.

3. Do not throw objects at high altitudes during installation, so as not to hurt passers-by. Not only that, during the installation process, it is also necessary to pay attention to observe whether there are obstacles around the building, and if there are, the obstacles need to be removed before installation, so as to avoid accidents.

With the continuous development of the economic level, many small villas or self-built houses have installed home elevators, so what are the installation precautions for home elevators? Next, pchouse will take you to understand.

1. Safety. In the process of installation, the home elevator must be made of steel structure in the shaft as required, so that the elevator car and system equipment can be firmly installed, otherwise it will endanger safety.

2. Sound insulation. The upper and lower tracks of the home elevator will produce noise, and the shaft must be soundproofed, otherwise the people who live next to the elevator will be disturbed by the noise.

3. Level. The home elevator door and the interior of the elevator should be kept at the same level as the hardcover ground finish surface of each floor, so that users can walk up and down the elevator smoothly, otherwise it is easy to fall.

I think the most important thing is to find a professional company to install a little better, otherwise it is a peace of mind to install it, if there are a bunch of problems it is not good, my friend's villa is very good, it looks very atmospheric, practical and safe, if you have money, you can install one, ha.

<>1.Construction elevator drivers must be trained in special safety technology, pass the examination, and be certified to work. Strict drunken work.

2.The driver must be familiar with the performance, structure, maintenance and repair knowledge of the elevator operated, and fill in the mechanical resume and the prescribed report in a timely manner according to the regulations.

3.Within 5m around the construction elevator, flammable, flammable materials and other sundries shall not be stacked, and trenches, pits and grooves shall not be dug within this range. A protective shed should be erected at the elevator ground inlet.

4.When the ladder cage is repaired, if the weight of the ladder cage is lower than the counterweight after removing the parts, the ladder cage must be locked on the guide rail frame.

5.It is strictly forbidden to use the derrick of the construction elevator to support horizontally and vertically, pull ropes, slogans and other items unrelated to the elevator.

6.The tower type lifting machine or other lifting machinery for the construction on the same site should be more than 5m away from the construction elevator, and there should be anti-collision measures that can be matched with the town ear.

7.After the installation of the construction elevator is completed, it must be inspected and accepted by the relevant personnel before it can be put into use.