After the laptop is reinstalled, the system becomes black and the screen appears like this

If it's not**patch,Generally don't prompt reboot (there is an installation requirement to restart,I haven't heard**To restart,Unless it's a virus),If you can see the BIOS at boot,It means that there is no big problem,Press F8 after the BIOS interface,Select the last normal boot (equal to restoring the previous state),If you can successfully enter the system,Then you have to do a good job of antivirus,Check the hardware and driver。

If it doesn't start normally, it's best to find a system disk, enter PE, back up the data, and then reinstall the system.

Are you sure the system is already installed?

Agreed, install a better system.

It's basically a one-click installation, and if there is a problem, it will be safe.

Otherwise, it's not a hardware problem.

A flickering cursor in the upper left corner is a typical indication of a problem with your system or hard drive.

1. After booting up, keep pressing the F8 key to bring up the advanced startup items, enter the "Safe Mode", enable the "System Restore" function, and restore the system to the time period of the last normal boot. If you don't have the "System Restore" feature enabled on your system, you will have downloaded all the drivers, programs, and patches you have recently installed.

Second, if it doesn't work, there should be a problem with the system. It is recommended to reinstall the original system.

3. If it doesn't work, there is a problem with the hard disk. It is recommended to use a professional hard drive detection tool to conduct a comprehensive inspection of the hard drive.

Fourth, if it doesn't work, there is a problem with the motherboard. It is recommended to send it for repair.

1. After booting up, keep pressing the F8 key to bring up the advanced startup items, enter the "Safe Mode", enable the "System Restore" function, and restore the system to the time period of the last normal boot. If you don't have the "System Restore" feature enabled on your system, you will have downloaded all the drivers, programs, and patches you have recently installed.

Second, if it doesn't work, there should be a problem with the system. It is recommended to reinstall the original system.

3. If it doesn't work, there is a problem with the hard disk. It is recommended to use a professional hard drive detection tool to conduct a comprehensive inspection of the hard drive.

Fourth, if it doesn't work, there is a problem with the motherboard. It is recommended to send it for repair.

It's not installed.,Reinstall it and see.,Isn't it ** not right.。

**This? Send a picture to see what the problem is.

Reinstall the system computer boot black screen solution steps:

1. Press and hold the power button to force the shutdown, then press the power button to start the computer, and press the F8 key before entering the system screen.

2. Use the arrow keys up and down to select safe mode, and then press enter to enter.

3. Right-click on your computer in safe mode and select Manage.

4. Select Device Manager in Computer Management, click on the graphics adapter, right-click the graphics card driver and select Uninstall.

5. Check the delete driver software of this device and click OK to uninstall all the drivers under the graphics card, and then reboot the display to be normal.

7. After the installation is completed, the black screen of the computer will be solved when the system is reinstalled.

There are two possible scenarios for a computer to reinstall a black screen:

One is that after clicking OK in the hard disk installer, the computer should automatically restart after shutting down, and automatically enter the ghost interface, however, it can't enter the ghost interface, but a black screen, plus an English prompt, as shown in the following figure:

This is due to the hard drive installer that matches the computer. 、

The second is that after the ghost is successful, the screen is black when restarting the computer, which is a hard disk mode problem.

Now in the hard disk installer, click on the solution to the black screen after the OK, which is introduced as follows:

1. Replace a different version of the hard disk installer.

2. When the black screen appears, you can continue to use the command to operate.

1. Enter ghost

2. Press the OK button.

3. At this time, the English version of ghost will appear on the screen interface, as shown below

4. Press the OK button. As shown below:

5. Use the tab key and arrow key to the local, as shown in the following figure

6. Use the tab key and arrow key to enter the partition, as shown in the following figure

7. Use the tab key and arrow keys to enter the slave mirror. As shown below:

8. Enter the largest file marked with a small fish, as shown in the following figure:

9. Click OK. As shown below:

10. Click OK. As shown below:

11. Click OK, as shown below

12. After clicking y, you will enter ghost normally.

It is estimated that there is a problem with the system you have installed. You can try this.

Special note: If there is an accident during the installation process or the installation of individual machines is not satisfactory or ideal, or there are hidden partitions in some hard disks, please enter the PE system to repartition and reinstall. If you are a laptop, there are three modes of ATA AHCI IRRT in SATAoperations in BIOS, you can try to change it and redo it.

It feels like overload protection, take it to the repair computer shop and fix it. Or just get it and fix the TV.

Hello friends:

Causes and solutions for black screen after reinstalling the system:

The first is: the reason for the resolution:

1。Reason: This is mainly due to the black screen caused by the low resolution.

2.Solution:

1) Force the computer to shut down, then turn it back on and press and hold the [F8] key on the keyboard.

2) Go to the Windows Advanced Options menu, then use the up and down keys on the keyboard to select [Enable VGA Mode] and press the Enter key.

3) When selecting the operating system, select: Microsoft Windows XP Professional Enter. Enter the system.

4) After entering the system, the lowest resolution of the system is displayed. Now you can operate without a black screen.

Note: 19-inch LCD monitor (plain screen) 1280 1024

19" LCD monitor (widescreen) 1440 900

20" LCD monitor (widescreen) 1600 900

22 inch LCD monitor (widescreen) 1680 1050

24" LCD monitor (widescreen) 1920 1200

The second reason: the system is not installed well, can not be booted, Jianyi to change the system and reinstall.

The third reason is that the main boot record is wrong, resulting in the failure to boot the system, and Jianyi can rebuild the main boot record.

Hope it helps, I wish you happiness

Is it a black screen all of a sudden? Does the monitor's light come on after the screen goes black?