I only have one network cable and the other end is at the landlord s, how can I complete the setup?

If you don't have a login password, you can do it if you do, but your landlord can change it.

Connect the computer network card with the LAN port of the router with a network cable and turn on the power of the router;

Enter the default username: admin and the default password: admin; Click OK.

Click Setup Wizard in the left rail, click Next;

Click on ADSL Virtual Dialing (PPPoE) and click Next;

Enter the bandwidth, password, and click Next;

Click Done.

Here's how to set up your router:

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: Generally, there are three types as follows:

ADSL dial-up: Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet (when you are not connected to the router), you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP Mode", and enter your fixed IP address, subnet mask, gateway, DNS domain name server and other parameters correctly.

4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the corresponding connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

How to configure the wireless router connected to the home network cable:

1.Connect the wireless router to a higher-level network device (e.g., modem, first-level router).

Connect the home network cable to the WAN port of the router, and when the WAN port light flashes on the router, the connection is successful.

2.Connect your computer wirelessly to your router.

The computer searches for the router's wifi name (the default wifi name is located on the nameplate on the back of the router) and connects to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the wireless gateway configuration page.

Open a browser, enter the IP address of the router gateway (usually, the default value is located on the nameplate on the back of the router) to enter the gateway configuration page. (This interface will pop up automatically for new routes).

4.Set up a wireless router to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and wifi password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key.

6.After the setting is completed, the router will automatically restart, please enter the new wifi password to connect, and you can access the network.

First connect the computer and the router with a network cable, then set the computer IP address to, then enter the route, the original login account password admin, and then check the wireless options inside, enable the wireless, set the password, turn on DHCP, and then log out, turn on the computer's wireless, set the wireless IP address to automatically obtain, and then connect the wireless sent by the router.

I don't know the account password, there is no way, http: go in the username and password are admin and then set up the router step by step, to know the broadband account password, I don't know if it doesn't work

Hello, after you have purchased the routing settings, you can follow the steps below to set them up!

1. Connect the home network cable to the WAN port of the router, 2. Connect your computer with another network cable at one end, and connect the LAN port of your router at the other end

interface! 3. Open the computer, open the browser, enter the route login IP in the address bar, 4, enter the route login account and password in the pop-up dialog box, friendly reminder, if you don't know the route login IP, login account and password.

code, you can turn the route over and look at it, and there is a writing on the back of the route!

5. After entering the routing setting interface, the quick setting interface will generally pop up, and you can select the broadband dialing method in this interface.

PPPoE, enter your Internet account and password!

6. After the settings are completed, save the exit and restart the route!

Once the routing restart is complete, your routing hardware connection and setup are complete!

In addition, there is another point to remind that if your home is a ** line and there is a cat, it is recommended that you turn off the power of the cat when you set the route, and when the route is set up, turn on the power of the cat!

The above is your route setting method, after the route setting is completed, connect to the three guest rooms with network cables from the remaining LAN ports of the route!

It's okay to buy a router with wireless one is better.

Buy a router, there are four breakout ports on it, one for your own use, the other three are connected to them, according to the manual on the route to set up your computer, it's very simple, about four or five steps.

Buy a router, set it up, and connect it. Those who make computers will do it, and let those who sell computers do it.

Buy a router and set it up on your computer.

The network cable can directly access the Internet, and it is also a good choice to buy a switch.

When connected to the LAN port of your router, your router is a switch, but there are two things to pay attention to:

1.The network cable connecting the LAN port of the router and the wall network port should be purchased as a cross cable, and the standard network cable directly connected to the computer should not be used (according to the length, it is also a few yuan a piece, and computer accessories are sold).

If you use an existing network cable to connect your router's WAN port:

Don't use a hub, a switch is even more not.

You're the account password of Hangzhou, right?

Let the landlord split two straight from the router LAN cable to you. Directly mount to 2 PCs.

Anyway, you are also renting a house, although the landlord's broadband is exclusive broadband, but there are more tenants, everyone still needs the same card. There is no solution to this.

Unless you call 10,000 by yourself and then pull the root line in, then you will be separated from the landlord.

Please note here that you do not use your landlord's ID card, but register with your own.

You said that she used the route to divide the line out, and you used the route again, this will not work, she is right not to tell you.

The cable that was connected to you was originally usable, but it was wrong for you to add the router to set the account password! This will conflict with the IP.,Not only will her account be disconnected at that time.,You can't connect yourself.。。。

What is said below can be connected, but you don't have any meaning, if the landlord is a 2m broadband, the router will be crossed to connect the router.

Your network resources are only 2M, no matter how much you jump, the broadband will not become larger. It's simply in vain!

Use your router as a switch, it's totally fine!

You use the original network cable to connect to the computer, ipconfig all, look at your network, the address of the router, the address of your host. ok！Use this address to set up the WAN port of your router, DHCP will be automatically assigned, connect to 4 computers, and surf the Internet! ok！

Use routing, route settings.

The WAN port IP is set to be dynamically automatically obtained, and it cannot be PPPoE

The LAN port IP is set to 2 253 numbers), and you can access the Internet by setting your two computer network cards to automatically obtain.

Connect directly to the router, set up no need for his account password, and directly use your own router for 2 computers.

Isn't it okay to have two lines directly?

Connect the WAN port, and then log in to your route wirelessly, set the next WAN port, set up a fixed IP, gateway, DNS, assuming the landlord's router address is, your route needs to be set to a different network segment, set it to or something else, the DNS and gateway in the WAN port settings are set to the landlord's routing address, and the IP of your machine will automatically search or specify the address in the network segment of your route.

The cable can only be plugged into the LAN port, because your line itself is split out on the router, and only the modem coming cable can be plugged into the WAN port. You need to change the address settings of your router so that it is not in the same IP range as your landlord's route.

It's normal... In your case, it is obvious that you need to set up a secondary route. Your wireless router will only work.