How to solve the slippage of the conveyor belt? What to do if the conveyor belt slips

Conveyor belts. Slippage is also a type of production that is often encountered in production.

Fault. We should find effective solutions to keep our production up and running. To overcome the phenomenon of conveyor belt slippage, we must first find the cause of the slippage before we can take effective solutions, and the common causes and effective solutions are as follows:

The initial tension of the conveyor belt is too small. The conveyor belt leaves.

Drum. The tension is not enough to cause the conveyor belt to slip. This situation usually happens at startup, and the solution is to adjust.

Tensioning device. Increase the initial tension.

between the transmission roller and the conveyor belt.

Frictional force. Not enough to cause skidding. Most of the reasons for this should be water on the conveyor belt or a humid environment. The solution is to add some to the roller.

Rosin. End. But be careful not to add it by hand, but blow it in with a blower device to avoid happening. Personal accidents.

Tail rollers. Bearing.

Damage does not turn or go up and down.

Roller bearings. The damage does not turn too much. The cause of the damage is that the tail floats and sinks too much, and it is not repaired and replaced in time, which has been damaged or rotates inflexibly. Parts. Envoy.

Resistance. Slippage due to enlargement.

Starting too fast can also cause slippage.

At this time. Can be started slowly. If the squirrel cage motor is used, it can be jogged twice before starting, which can also effectively overcome the slippage phenomenon.

of conveyor belts. Load.

Oversized, exceeded.

Motor. Ability can also slip. The positive side of skidding at this point is that it protects the motor. Otherwise, after a long time, the motor will be burned. But for the operation it is slippery.

Accident. There's something I don't understand.

You can go to Qingdao Double Tiger.

Rubber and plastic. Take a look at it.

Belt slip teaches you a trick to solve easily, if you don't believe it, you can try it.

The solution to the slippage of the conveying manuscript belt is as follows:

1. Because the initial tension is too small, the tension of the conveyor belt leaving the pulley is not enough to cause the conveyor belt to slip, and the solution is to adjust the tensioning device and increase the initial tension.

2. Due to the lack of friction between the transmission roller and the conveyor belt, the conveyor belt slips, the solution is to blow a little rosin powder into the drum with a blower device;

3. Due to the slippage caused by the starting speed is too fast, the solution is to adjust the conveyor belt to clear the potato and start it slowly;

4. Due to the excessive load of the conveyor belt, which exceeds the capacity of the motor and causes slippage, the solution is to reduce the load of the conveyor belt, that is, to reduce the goods conveyed each time.

Conveyor belt slippage refers to the phenomenon that the conveyor belt and the driving device cannot transmit power well during operation, resulting in the failure of the conveyor belt to operate normally. Here are a few common causes of belt slippage:

Insufficient tension: When the tension of the conveyor belt is insufficient, it cannot generate enough friction to push the conveyed materials of the noisy Qinmu. This can be caused by improper tension adjustment, faulty tensioners, or aging belts.

Wet or viscous materials: Some wet or viscous materials can form a thin film on the surface of the belt, reducing friction in contact with the belt. This makes the belt slippery and unable to transfer power effectively.

Uneven load distribution: If the material is unevenly distributed on the conveyor belt, it can result in excessive load in some areas and insufficient load in others. This uneven load distribution can throw the belt out of balance, leading to slippage.

Belt slack or wear: Belts may become slack or worn after prolonged use. Loose belts can cause a lack of tension, while a worn belt surface has a reduced coefficient of friction, which can cause slippage.

Drive failure: When the motor or reducer that drives the belt fails, it may not be able to provide enough power, causing the belt to slip. Shoukai.

How to deal with material slippage on the conveyor beltHello dear, belt slippage solution for belt bogao conveyor: With the wide application of belt conveyors in industry and transportation, belt slippage has become a common problem for belt conveyors. This article provides you with a solution to belt slippage in belt conveyors:

Belt conveyors are used in agriculture, industrial and mining enterprises and transportation industries to transport a variety of solid lump and powder materials or finished items. The belt conveyor has the advantages of continuous, high efficiency, large inclination transportation, safe operation, easy use, easy maintenance, and low freight. It can be seen that the belt conveyor plays a role in reducing the project cost and saving manpower and material resources in industrial production and transportation.

However, belt conveyor belt slippage is one of the most head-scratching problems in the work process, let's learn about the belt conveyor belt slippage solutions? Belt conveyor belt slippage solution: 1

The belt conveyor using the weight tensioner can be solved by adding a counterweight when the belt of the belt conveyor slips, and the belt does not slip until it is added. However, too much should not be added, so as not to expose the belt of the belt conveyor to unnecessary excessive tension and reduce its service life. 2.

Solve the slippage of spiral tensioning or hydraulic tensioning belt conveyor belts. Using a belt conveyor with spiral tension or hydraulic tensioning, the tensioning stroke can be adjusted to increase the base tension when the belt slips. However, sometimes the tensioning stroke is not enough, resulting in a permanent deformation of the belt conveyor belt, and the belt can be cut off and vulcanized again.

3.The use of nylon belt or EP is required to have a long tensioning stroke, and when the stroke is insufficient, it can also be re-vulcanized or increased to solve the belt slippage problem of belt conveyor. 4.

According to the problem description you provided: when there is water on the conveyor belt that causes slippage, the following measures can be taken to solve the problem:1

2.Increase friction: To increase the friction between the belt and the object, there are a few methods that can be used.

For example, belt hall contents can be sprayed with anti-slip agents, coated with anti-slip materials, or belt materials with a high coefficient of friction can be used. 3.Adjust belt tension:

Properly adjusting the belt tension can also help reduce slippage. Depending on the situation, the tension can be increased or decreased by adjusting the tensioner of the conveyor belt. 4.

Check the belt structure: Make sure the belt is structurally intact and there are no damaged or loose parts. If necessary, repair or replace damaged parts to ensure proper belt operation.

5.Control water sources: For water sources that may persist, steps need to be taken to control the flow of water, such as repairing leaking pipes or installing waterproof barriers.

This prevents water from re-entering the conveyor system.

Summary. Material slippage on the conveyor belt may be caused by the following reasons:1

Insufficient belt tension: If the belt tension is insufficient, the material will not be able to gain enough friction during movement, resulting in slippage. 2.

Belt surface wear or contamination: If there is wear or contamination on the belt surface, it can also affect the coefficient of friction between the material and the belt, which can lead to slippage. 3.

The humidity of the material is too high: some materials that are easy to absorb water are prone to problems such as adhesion and increased viscosity after being wet. This reduces the coefficient of friction between it and the belt and makes it prone to slippage.

4.The conveying speed is too fast or too slow: if the conveying speed is too fast, it may cause the material to fall and splash; If the speed is too slow, it may cause problems such as accumulation and stuck.

These can cause slippage.

Material slippage on the conveyor belt may be caused by the following reasons:1Insufficient belt tension:

If the tension of the conveyor belt is insufficient, the material will not be able to obtain enough friction during the slowing process, resulting in slippage. 2.Belt surface wear or contamination:

If there is wear or contamination on the surface of the belt, it can also affect the coefficient of friction between the material and the belt, which can lead to slippage. 3.The humidity of the material is too high

Some materials that are easy to absorb water are prone to problems such as adhesion and increased viscosity after being wet. This reduces the coefficient of friction between it and the belt and makes it prone to slippage. 4.

The conveying speed is too fast or too slow: if the conveying speed is too fast, it may cause the material to fall and splash; If the speed is too slow, it may cause problems such as accumulation and stuck. These can cause slippage.

Workarounds include:1Adjust the conveyor belt tension to ensure its normal working condition; 2.

Regularly clean and maintain the surface of the conveyor belt to ensure that it is smooth and flat; 3.Control the humidity of materials and take corresponding protective measures; Sell Min 4Adjust the appropriate operating slag speed according to actual needs.