What should I do if my Glash tte watch gets water vapor?

Water treatment for watches:

Method. 1. If the watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb about 15 cm, bake for about 30 minutes, and the water vapor in the watch can be moisture. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method. 2. Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method. 3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will all disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

1. When there is very little fog, just put the watch in a cool and ventilated place and let it dry for a period of time, and the fog will dissipate.

2. Wear the watch backwards, put the dial facing inwards and the bottom of the watch facing outward, and wear it for a few hours to achieve the defogging effect.

3. Place the watch in a sealed container with granular silicone, and after a few hours, it can also achieve the effect of defogging. If there are no silica gel particles, you can also use rice instead, and after a day of resting, the mist can also be sucked away.

4. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate the moisture. Do not bake the watch close to the fire to avoid deformation of the watch.

If there is a slight fogging, it can be easily solved by the above methods.

The only best way to repair the watch is to open the back cover of the watch, treat the movement in the watch, and then oil each movement part. Therefore, if water enters the watch, the movement parts in the watch will be stained with water, which will lead to the hazard of rusting parts.

Therefore, the repair of water ingress in the watch should not only remove the steam in the watch, but also maintain the movement in the watch to prevent the harm of rust in the parts.

In fact, if you are the Glashütte watch metal big, you can find a watch, a store that does not have a watch, and the store will help you into that treatment.

If the watch gets water vapor, it should slowly evaporate in a dry place, and there is no need to manage it.

Send it directly to the after-sales service, or find a large maintenance shop for repair.

Glashütte Watch Aftermarket Repair Center: 400-659-0877

A very important reason for the fast movement of mechanical watches is the magnetization that we mentioned at the beginning. The most likely reason for the rapid operation of a mechanical watch is the influence of magnetic fields. After the hairspring is magnetized, the rings between the rings are only visible when worn.

There are sticky or short cycles, especially when the hairspring is on the façade. It sags due to its own gravity, and the shaking of its arms aggravates its radial motion and thus shows the effects of magnetic energy.

If the water ingress is not very serious, but there is fog on the watch glass, you can directly wear the watch on the wrist directly, and the best solution is to go to the after-sales center in time, and the maintenance technician will remove all the parts and wipe the oil one by one to ensure that the watch has no possibility of rust. It should be noted here that it is timely, delaying the repair will often delay the best time for Carl F. Bucherer watch maintenance, resulting in damage to the parts.

There are generally three ways to enter the water in the watch, the watch is worn backwards, the desiccant is removed and the lamp is baked to remove the water, it may seem that the effect is not bad, but the fact is not satisfactory, those methods can only remove the water stains on the surface, and the water stains that penetrate into the movement can not be removed with certainty, and it is not too much to treat those small watches, but for those famous watches, if this method is adopted, I am afraid that it will be regretted in the future. If this method can be handled completely, then the repairer will not have to eat. It is recommended to send it to a professional repair point if it enters the water.

Hello, the watch water generally has water mist or water droplets on the watch glass, and it will corrode the movement for a long time, resulting in inaccurate or non-time, so the earlier the watch water treatment time, the less damage to the movement, the recommended treatment methods are as follows:

Law. 1. Place the vent - dry the watch with a dry paper towel and then place it in a cool and dry vent for a few hours, and do not place the watch directly in the sun or dry, which is to prevent water mist from flowing into the movement.

Law. 2. Silicone drying - for the water inlet of the mechanical watch, you can use the granular substance of silica gel to absorb water, put the two in a closed container, and take it out after a few hours, and the water mist inside will be cleaned up; If it is a quartz point clock, you can take a few small pieces of calcium chloride, wrap them in gauze, and then open the electronic watch cover and seal it.

Law. 3. Wipe oil and remove rust - method 1 and method 2 can only clear a slight water mist, and for some more serious water ingress, these two work earlier, which is not enough for the rescue time of the movement, at this time it is best to find a professional watch repair center for ** maintenance, oil wiping treatment.

Glashütte Watch Care Center: 400-659-0877

Quartz watches allow a margin of error of 15 seconds per month. Quartz watches are powered by battery energy, and the typical battery life varies from 12 to 24 months, depending on the movement used in the watch. If your watch has a weak current display, the second hand will only jump every four seconds when the battery is almost exhausted, if this happens, you should replace the battery immediately.

If you find that the time is slow, it may be caused by insufficient power, you can go to the authorized maintenance center to check the power of the two-pin quartz meter to adjust one minute faster to compensate for the gap between the magnetic wheels.

The Shanghai Glashütte watch is in Room 918, 9th Floor, Landmark Plaza, Nanjing East Road Pedestrian Street, Huangpu District, Shanghai, and the watch must be kept dry at all times. If you accidentally get wet, wipe the water off your watch carefully and thoroughly with a dry, soft, absorbent cotton cloth to avoid rust.

Hello, the inside of the watch is flooded, I suggest that you go directly to the relevant after-sales service center to deal with it, and professional things should be done by professional people. You can also click on my homepage to consult and understand the after-sales service, and deal with the degree of water ingress in your watch to ensure that the watch is in good condition. It can also avoid unnecessary troubles caused by unfamiliar table structure when you operate independently.

Prepare a little paper towel or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. Later, you will notice that the moisture in the movement gradually disappears. Welcome to consult.

If the watch is flooded, it should be sent to the service center for repair in time, so as not to corrode the inside of the movement and increase the maintenance cost over time.

The address of Chengdu is in Room 05, 24th Floor, Sichuan Aviation Plaza.

Dear users, hello!

Book a repair service in advance and enjoy priority service!

Accessories: Original accessories throughout the process** to ensure the perfect operation of your watch!

**: Strictly implement the unified guide price of the brand!

Hello! Glashütte's after-sales center is in: Room 808, Block E1, Oriental Plaza Office Building, No. 1 East Chang'an Street, Dongcheng District, Beijing.

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Note: In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot vapor, and pay more attention not to be exposed to rain on rainy days.

What should I do if my watch gets water?

1. If the watch is soaked in water, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the water vapor in the watch can be eliminated.

2. Put it in a rice jar and bury it deep in the dried rice for a period of time, if it is fast, you can see obvious results in one night.

3. You can use a granular substance called silica gel to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will disappear.

4. Take a hair dryer to dry, and then apply a layer of transparent nail polish on it to avoid impurities and prevent rust.

5. If there is water vapor in the watch, you can wear the watch face inward and the bottom shell outward, and wear it on the wrist to eliminate the water vapor in two hours. If there is too much water in the watch, the case must be opened and scrubbed. If you are not sure to deal with it yourself, you should send it for repair in time.

1. Use silica gel to dry the granules. If water enters the case, a granular substance called silicone can be used to put the watch in an airtight container with the water that has accumulated water, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and the accuracy and longevity of the watch will not be compromised in any way.

The silica gel, which has been absorbed many times, can be dried at 120 degrees for several hours, has a renewable water absorption capacity, and can be used again and again.

2. Bake hot with an electric light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes, which will eliminate the moisture. Be sure not to bake the watch mask directly near the fire to prevent the watch from being deformed by heat.

3. Wear the watch backwards. You can also wear the mask with the cover facing inward and the bottom shell facing outward, and wear it on the wrist, and the moisture will be eliminated after two hours. If the water ingress is severe.

4. Send it to the watch shop to wipe the oil. None of the above three methods can remove water vapor, and it should be sent to a repair shop immediately to wipe the oil to remove moisture from the movement and prevent rust on the parts.

5Dry with a hair dryer, the temperature should not be too high, and the wind will be mild until the moisture on the glass is not visible.

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

Some people think that their watch is a waterproof watch, and they often fall into some misunderstandings. For example, wearing a watch to take a hot bath or go to a sauna is completely wrong. Because the watch itself is not an absolutely sealed shell, that is to say, waterproof is not necessarily waterproof vapor, no matter how many meters it is indicated, it cannot be used in hot water greater than 40C°.

If the water ingress into the watch is more serious, remember not to dispose of it by yourself to avoid unnecessary losses. It is recommended to take the watch that has been damaged by water to a professional repair shop for oil polishing to remove moisture from the movement and prevent the watch parts from rusting.

Even if the watch is water-resistant, not all water is protected against water. For example, the 30-meter water resistance can only prevent hand sanitizer, face wash, rain, car splashing, etc. If you take a bath, swim, etc.

The watch can't stand it anymore. Consumers are reminded that no matter how deep the water is waterproof, they should not wear a watch sauna. The heat of the steam accelerates the deterioration of the waterproof rubber ring and does not protect the movement properly.

If there is water in the watch because the quality of the watch is still not up to par, and the closure is not strict, you must negotiate with the seller.

Glashütte Watch Aftermarket**: 400-659-0877

Generally speaking, if there are water stains on our Glashütte watch, and after a period of time there is a shutdown on the watch, then you can judge whether there are water stains on the watch, and if there are water stains on the watch, the error on the watch is large, and you can also judge whether there are water stains on the watch. In addition, when we look at the hands in the Glashütte watch, the hour hand in the watch does not look very clear, and we can also tell that the hour hand in the Glashütte watch has been flooded.