Glash tte watch steals stopping, watch does not go, what is the reason

Hello, the reason why the watch does not go could be:

The power of the table is insufficient.

An automatic watch only needs to be wound by moving your arm, but if you don't exercise much, or if you don't wear your watch for too long, the watch may not be able to run out of time or stop due to lack of power. Of course, you don't have to throw your arms as a hula hoop in order to wind your watch, just move normally.

2.Wearing time is too short.

If it's really caused by too little exercise, don't worry, just take off your watch and shake it horizontally for about 2 minutes before going to bed, and of course you can also shake it for 4 minutes, because then it can walk longer. If your watch can be wound, you can also wind it clockwise. In order for your watch to last longer, it is recommended to have him wear it on your wrist for at least 6 to 8 hours a day.

3.Hairspring failure.

If neither of the above two reasons is the case, it may be the cause of the hairspring. If you exercise too much, the clockwork will be tighter. If it is really a lack of power caused by the winding, usually between 9 and 12 o'clock in the evening, the "calendar function table" at this time his needle wheel began to drive the calendar wheel, the load is large, the watch is tired, at this time if the power is insufficient and no one pushes it, it is easy to stop.

During this time, don't reverse the dial, many mechanical watches have a plastic calendar wheel, and if you are not careful, you will break the gear, if you break the tooth, it will be stuck at this time every day, or it will no longer jump until a fixed date. That's why the mechanical watch stopped.

4.Bump failure.

The parts of the watch are very delicate and small, if you are careless and accidentally bump into it, or if you are healthy and bump into it. This can easily cause the movement parts to fall off or break directly.

All automatic watches must be worn or wound regularly in order to function properly. If the mechanism stops working for a long time, it will cause the watch to deteriorate for a long time. Generally speaking, the power reserve of a large three-hand watch is probably no more than 38 hours, which means that if you do not wear the watch for more than 45 hours, the watch will eventually stop due to the exhaustion of the mainspring.

If you only have one or two automatic watches in your collection, you won't have to worry about wearing them often or stopping them to wind them in order to wind them. But if you have a large collection of mechanical watches, you have to make sure that all the watches don't stop, and everyone will feel a headache and trouble.

The following is an introduction to the five common reasons for the inaccuracy of the watch time

1: Insufficient power reserve: You need to check whether the power is sufficient, if the amount of exercise is small, the power reserve may be insufficient, you can supplement the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2: Insufficient power: If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3: The watch has been hit or impacted: the watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4: Need maintenance: The lack of oil in the movement or the wear and aging of the internal parts may cause the problem of running time, which needs to be maintained, and needs to be sent to the designated maintenance point for maintenance services.

5: In addition to the above common situations, some ambient temperatures affect the watch by magnetism: if the balance spring of the watch is magnetized, the watch will not be accurate.

1. Magnetization of the watch: Many things with magnetic fields are often together with the watch, which leads to the phenomenon of magnetization of the watch, which causes the watch to be inaccurate. After being magnetized, the watch may stop, slow, or fast.

After the watch is magnetized, its magnetism will not recede by itself, in which case it can only be demagnetized. Therefore, you can only go to a professional watch repair center for demagnetization so that it can return to normal.

2. Lack of maintenance: mechanical watches are maintained every 2-3 years, and quartz watches are maintained every 4-5 years. Watch maintenance requires the movement to be completely disassembled, cleaned, oiled, reassembled, adjusted, and functionally checked; Repair or replace any worn or malfunctioning movement components.

If the watch lacks maintenance, it will cause the parts to wear out, the sludge will dry up, affect the normal running time of the watch, and make the watch appear fast and slow. Regular maintenance of the whole machine can effectively prevent the occurrence of various failures of the watch.

3. Mechanical failure: Mechanical failures such as watch hairspring failures, escapement system failures, and parts and components may cause the watch to appear fast and slow, so when the watch is abnormal, you can first pull out the crown and take it to a professional maintenance organization for the maintenance technician to check the reason.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

First of all, you look at your hand to indicate whether it is manually wound or automatic, and there are several reasons why the watch does not go in general

First: mechanical watches need to be cleaned and maintained within 2-3 years of wearing.

Second: If the watch type is fully automatic winding, there may be a reason for the lack of power that causes the watch not to go.

Third: it is a problem with the movement, it is recommended to go to a professional maintenance place to check it.

Reason for stopping:

The more common reason may be the lack of kinetic energy, automatic mechanical watches do not need to be manually wound, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch uses the arbitrary swing of the rotor to wind up, and the rotor swings with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But if you often wear it on your hand and don't walk, it may also be a lack of kinetic energy, and then we need to manually wind it.

After the above methods, the machine is not gone, here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be the failure of the mechanical watch, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair.

Lacking in power, an automatic watch uses the movement of the arm to complete the winding. If the watch is left for too long or the amount of arm movement is less every day, the mainspring energy of the watch will be due to insufficient winding, and it is easy to produce inaccurate timing or night stopping. The hairspring is faulty, and the clockwork will be tighter if the amount of exercise is large.

If there is a problem with the upper bar mechanism that causes insufficient power, it generally appears between 9 o'clock and 12 o'clock in the evening, "with a calendar function table" because at this time the hour wheel begins to drive the calendar wheel, and the load is large, if the power is insufficient, it is easy to stop during this time period. This time should not be reversed dial pin, now many mechanical watches use plastic parts of the calendar wheel, accidentally will break the gear, once the tooth is broken, every day at this time will be stuck, or to a fixed date will no longer jump. As a result, the mechanical watch was stopped.

Bump failure, the watch is a precision instrument, once the bump receives a violent vibration, then the parts may fall off or damaged, you can make the watch steal stop. The above three are common faults of mechanical watch stealing, how to judge the reason for their mechanical watch stealing, you can judge according to the above three, if you are not clear, you can go to [8th Floor, Block E1, Oriental Plaza Office Building, East Chang'an Street, Dongcheng District, Beijing] with an instrument to detect, so that it is more safe.

Reason for watch stealing:

1. Anyone who knows a little about mechanical watches knows that fully automatic mechanical watches rely entirely on the swing of the arm to complete the winding. Therefore, if the watch is left for too long or the amount of arm activity does not meet the requirements of the watch winding every day, the watch will cause the mainspring to be winding and the potential energy is insufficient, which will cause the watch to be unstable or stop when it is not worn at night.

2. If you accidentally bump or fall into the watch in daily use, and hit the watch hard, it may cause the movement gears and other parts in the watch to loosen and misalign, which will also lead to the situation of stealing the mechanical watch.

3. The failure of the hairspring is also one of the reasons for the stealing of the mechanical watch when it is running normally. If the amount of activity is too large, the winding mechanism will malfunction due to the tightening of the mainspring for a long time. It can also cause a lack of motivation.

1.A watch with a hand-wound movement should be wound at the same time every day as far as possible so that the watch has sufficient energy to operate in the next 24 hours.

2.The energy of a watch with a self-winding movement is the movement of the wearer's arm, so it does not need to be wound manually under normal wear, only when the wearer's movement is not enough to replenish enough energy to the mainspring, the manual winding method can be used to compensate, and the crown rotation is controlled within 20 revolutions when winding.

3.If a self-winding watch has not been worn for more than 40 hours, the movement should be reactivated by turning the crown twenty times when it is worn again.

4.To prevent moisture from penetrating the case and to maintain the water-resistance of the watch, make sure that the crown is locked at all times.

Reasons why the watch doesn't go:

The main core gear is misaligned, the watch is magnetized, bumped, and the oil sludge is dried for a long time. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch suddenly stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

1.Mechanical watches rely on mainspring windings to provide power, and the timekeeping is carried out by means of gearing. Mechanical watches are divided into manual and automatic winding.

Due to the complex structure, the phenotype is thicker and heavier. Because of the characteristics of the principle of time, it is affected by gravity, mechanical friction, temperature changes, usage and other reasons.

2.Mainly from the wearer's wrist activity, the wrist of the watch swings when the owner is active, so as to wind the watch, so when the wearer usually does not move much or does not wear it for a long time, the string force will be insufficient or empty, resulting in the watch is not accurate or stopped.

3.Automatic watches rely on the swing generated by relative motion to automatically wind, if the belt is in the hand, it is in a relatively stationary state for a long time, the watch can not be automatically wound, it will lose the ability to time, and there will be stopping.

4.Users only need to swing the watch dozens of times or up and down a few times (with hand adjustment function) to restore time. If you want to ensure that the automatic mechanical watch walks accurately, you should wear it normally for more than 8 hours a day.

1) Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. Especially for automatic watches, the efficiency of automatic winding is low, and the amount of arm activity needs to be larger, and typing on the keyboard while wearing a watch makes the range of motion of the wrist too small, and the winding efficiency is very low.

If the amount of exercise is small, it can be wound by manual winding.

2) Gear failure: Gear train failure such as deviation wheel and center wheel failure will cause the watch to stop secretly. The pallet fork touches the splint plate, the swing beam touches the hairspring, the outer pile or clamp, the fork head of the pallet fork is deformed and hits the disc or the fork head nail collides with the disc nail, etc., all of which can also cause the watch to stop.

These situations often require careful examination and testing to identify the problem and solve the problem.

3) Lack of maintenance: Mechanical watches need to be serviced every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated and silted inside. Friction between gears increases, causing slippage.

If there is a problem with the watch, you will need to take it to the place where the watch is repaired.

Glashütte Watch BAI Aftermarket Repair Center: DU400-659-0877

Why don't you leave the good quartz zhi watch? The reason is very dao

Simple, one of the main reasons for the first edition is that when the battery is completely discharged, the quartz watch machine stops working, it is generally recommended to replace the battery to avoid the low battery power after the battery leakage, and there will generally be a second pause for 4 seconds, and then a rapid jump of 4 seconds of walking state (previously it was a pause of 2 seconds); The second reason is that the gears of the quartz watch movement are faulty, and at the same time as producing a watch, they must pass through the level of installing the hands, if the hands are not installed, it may cause the hands to stop after going to a position, if it is not this problem, it may also be that there are impurities on the watch that will jam the hands, and then stop every time they move to which position.

Five reasons for watch time error and watch time inaccuracy:

1: Insufficient power reserve.

2: The battery is insufficient.

3: Having been hit or impacted.

4: Maintenance is required.

5: The watch is magnetized: If the hairspring of the watch is magnetized, the watch will not be accurate.