What to do if there is an inaccurate failure of the Glash tte repair shop watch after being hit

The following is an introduction to the five common reasons for the inaccuracy of the watch time

1: Insufficient power reserve: You need to check whether the power is sufficient, if the amount of exercise is small, the power reserve may be insufficient, you can supplement the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2: Insufficient power: If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3: The watch has been hit or impacted: the watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4: Need maintenance: The lack of oil in the movement or the wear and aging of the internal parts may cause the problem of running time, which needs to be maintained, and needs to be sent to the designated maintenance point for maintenance services.

5: In addition to the above common situations, some ambient temperatures affect the watch by magnetism: if the balance spring of the watch is magnetized, the watch will not be accurate.

Each watch has a different movement type, which leads to differences in the accuracy of each watch. The watch relies on the internal mechanism to control the uniform and accurate time of the watch, because the internal mechanism of the watch is affected by many external factors, such as gravity and ambient temperature differences, which will cause errors in the watch. In general, the error of mechanical watches is calculated on a daily basis, although they are different due to the differences in the movement model and manufacturing quality of each watch, but the error is generally less than 30 seconds per day, and this degree of error is normal.

Of course, some of the higher precision movements can have an error of about 10 seconds. In general, there are several situations that will cause the sudden increase in the timing error of the watch.

1. Insufficient power reserve: You need to check whether the power is sufficient, if the amount of exercise of the automatic watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of fast and slow.

2. The watch is magnetized: If the hairspring of the mechanical watch is magnetized, the watch will not be accurate.

3. Need for maintenance: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, and it needs to be sent to the designated maintenance point for maintenance services.

4. Hit or impacted: The watch is very precise, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause time problems.

5. In addition to the above common situations, the influence of some ambient temperature and the wearer's usage habits may cause an increase in the timing error. But you don't need to worry, please send the watch to the designated repair point for professional inspection and adjustment, and the watch can be restored to the normal error range.

The above 5 situations are usually the reasons that may cause the watch to have a time error, once the watch has a time error, we must find the reason, so as to find the corresponding solution, to avoid other reasons can not be solved in time and cause the watch to appear more serious.

If the watch stops due to a collision, it is likely that the internal movement or pinion will be rubbed and it will not function properly. As a result, the watch will not be able to move.

If there is a serious collision, the hands on the dial may stop or slow down due to vibration or loosening. Of course, there is also the case that the mirror surface is broken, and the remaining fragments are stuck in the movement of the pointer.

There is nothing wrong with the outside of the watch, but if the watch just doesn't go, it is recommended that you bring the watch to the after-sales center to detect the specific cause of the failure, so as to avoid your normal use.

Hello! If the watch does not go, in this case, there must be a problem inside the movement, it is recommended that you send it to the repair shop for inspection and repair in time to avoid further damage to the movement for too long. You can open the warranty coupon attached to the watch purchase, and there will be a service address on the warranty coupon under normal circumstances, or find a regular watch service center for inspection and maintenance.

Glashütte Watch Care Center: 400-659-0877

Deep scratches on the Glashütte case or strap should first be polished with an oil stone. This needs to be done under a magnifying glass. The aim is to grind the scratches evenly.

When the scratches are largely removed and flattened, choose sandpaper with the appropriate grain size and grind along the original grit pattern. Usually, all patterns will be radial around the center of the dial, so this is a careful job. It takes a little bit of time to make the grinding better and more realistic.

There are many reasons why your watch suddenly goes away, and it can be due to lack of power, faulty gears, lack of maintenance, or damage to other internal parts. In this case, it is recommended that you go to the relevant after-sales service center, or consult on my homepage. It can effectively help you solve the phenomenon that the watch does not go, and can also avoid the trouble caused by your own improper operation.

There are three reasons for inaccurate time:

First, the power is insufficient.

The power required by the watch is not the same, like a mechanical watch, it relies on the shaking of daily wear to store power, if you don't wear it for a long time, there is no power, then the watch will definitely stop or slow down. The manual one needs to be wounded up and down from time to time, and some rely on electronics to maintain rotation, so if the watch is inaccurate recently, it is likely that the electronics are out of power and need to be replaced.

2. External interference.

This is whether you pay attention to it when you wear it daily, for example, watches are relatively squeamish, waterproof, anti-magnetic, and shock-proof, if you don't do a good job, it is normal for the watch to be inaccurate. If you wear a watch that cannot be worn for strenuous exercise, and you wear it to play golf or badminton, the strong vibration may cause damage to the parts inside the watch, and the watch will not be accurate.

In addition, it is a cliché that watches are afraid of magnetism, if your job is to engage in some research things and need to be in frequent contact with large electronic devices, then try not to wear a watch, because the magnetic field existing around it will disturb the normal walking of the watch. Some people say that the watch is bought to wear, and the baby is not good every day, so why buy it? That's true, but you should also be careful when wearing it.

3. Proper maintenance.

The watch is more precise, there are more small parts, and the mutual fit between the parts can operate normally, so the haul is indispensable for friction, so the watch is oiled, and it will inevitably dry up after a long time, plus there may be some impurities into the watch, so it will cause the watch to go inaccurate, at this time you have to go to maintain it, clean up the watch.

Glashütte Watch Aftermarket Repair Center: 400-659-0877

1. The slower the watch, the more likely it is to be equivalent to an automatic mechanical watch, wear it normally for 8 hours a day, and the normal momentum can support the time, generally speaking, the watch can go normally for 36 hours, if you don't wear it often, the duration of the goods is not long, that is the reason for the lack of energy.

2. The watch may lead to dry oil, insufficient lubricating oil, difficult movement operation, no maintenance throughout the year, and the temperature is too low or too long.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

The Glashütte Warranty Error After-sales Service Center is located in Room 918, 9th Floor, Landmark Plaza, Nanjing East Road Pedestrian Street, Huangpu District, Shanghai, if you want to wear it every day, the best way to maintain it is to tighten the mainspring every two weeks to ensure that its gears run normally and smoothly. Gently rotate the crown until you can feel a slight urgency.

Mechanical failures such as magnetism, lack of maintenance, malfunction of the watch hairspring, escapement system, slippage of parts, etc., can cause the watch to be fast and slow. Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc.

Reasons and solutions for inaccurate watch time:

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the special repair shop for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy, and send the watch to a special maintenance point to check the power or replace the battery.

3. Having been beaten or impacted. The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to a special repair shop for testing.

4. Maintenance is required. Lack of oil or wear and tear of internal parts of the movement may cause time problems, which need to be serviced and sent to a designated repair point for maintenance services.

5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the time error.

Sending the watch to a designated repair point for professional inspection and adjustment can restore the watch to the normal error range.

Note: 1. Mechanical watches vary according to the model and manufacturing quality of the movement, and the error of the general watch within 30 seconds per day is within the normal range. Some of the higher precision movements can reach around 10 seconds.

2. Generally speaking, the accuracy of quartz watches is high, and the Swiss standard is that the monthly error is within 15 seconds. Some precision movements can be within a few seconds per year.

Outstanding Contribution List Hongcun 139 Featured Entry Premium Version 1 Synopsis.

Your Glashütte watch is not on time, in this case, you can go to the watch repair shop on the first floor of China Resources Vanguard on Dongge Road in Nanning to get it repaired.

After this watch is not implemented, you went to find him from the watch you bought? The shop asked him to continue repairing, which was more cost-effective.

Hello, glad to answer for you!

Reasons for inaccurate time: insufficient kinetic energy reserve of the watch, insufficient battery of the watch, the watch has been hit or hit by an external source, the watch has not been maintained for a long time, and the watch is affected by magnetic fields.

Solution: It is necessary to go to the after-sales center for testing and maintenance.

The name is to be used in the oversized supermarket to sell the target industry, it has a repairman, you can look it up there and consult.

There are many reasons why the watch is not accurate, and you need to take it to the after-sales service center for testing.

The address of Chengdu is in Room 05, 24th Floor, Sichuan Aviation Plaza.

My Glasti watch can't go anywhere, there is a repair shop at the third traffic light in Langdong District, Nanning, and the technical level of the master here is still good.

Glashütte Watch Repair Center: Room 01, 20th Floor, Yingli International Financial Center, No. 28 Minquan Road, Yuzhong District, Jiefangbei, Chongqing.

If it is a new watch that you just bought and the strap is broken without wearing much, then you can go to the aftermarket to replace it. Generally speaking, the warranty period of the watch is 2 years, and although the strap is not covered by the warranty in many cases, it can also be found after sale for those who have just bought it.

If the strap of the watch that has been worn for a long time is broken, then it can be taken to a special maintenance point for repair according to the specific situation, which is also more convenient.

Different brands of different styles and different price points of watches, watch straps are also different, there are leather, there are steel, but also chains, etc., for the belt to break it also depends on what the situation, if it is really serious, there is no way to repair, then it can only be replaced with a new one.

If the watch is the kind of decorative strap, usually the kind of chain, then if one of the sections is broken, you can completely remove it and don't want it, and then re-buckle it, which is similar to many people's bracelets.

The watch is worn on the wrist and neck, which is very convenient to look at, but once you find that you want to disconnect it, you need to find a way to solve it. It's better to be leather, and you can glue it up by yourself if it cracks a little, so it won't be so easy to break it all.

Since the maintenance requirements of each strap are different, you need to choose a watch according to your own needs. For example, leather straps are very high-end, and they can show a unique personal temperament, but they are very unsuitable for summer wear, because the sweat in the human body is very corrosive to the strap, and it needs to be maintained accordingly.