What is the reason for the water ingress of the Glash tte watch?

What to do if the watch gets water.

It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

Of course, there are also some daily repair methods for watches to get into the water:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

Many people don't pay attention to the problem of water ingress in the watch, and some problems will occur in the watch over time

First: Try wearing the watch backwards. Put the watch face inwards and the bottom case outward, put it on your wrist, and then send it to the repair center for processing, otherwise many metal parts inside the movement will oxidize and rust due to water vapor, causing more serious losses.

Second: Use silica gel to dry the granules. In the event of water ingress in the case, a granular substance called silicone can be used to place the watch in an airtight container with the water that has accumulated and remove the watch after a few hours.

Third: Dry with a hair dryer, the temperature is not too high, and the wind is mild until the moisture on the glass is not visible.

Fourth: After the watch is put into water, put it in rice, and after 24 hours, the water vapor is adsorbed.

None of these methods can guarantee that the moisture in the watch has been removed. If there is residual moisture and moisture in the watch, then the movement is very likely to be affected, which will affect the operation of the whole watch, and the later maintenance cost will be higher.

Hello! Glashütte watch into the water, you need to be cautious in this situation, first of all, the obvious water stains should be removed, and then sent to the brand after-sales or brand repair shop in time for testing and cleaning, washing and oil maintenance. Otherwise, if you do not treat it for a long time, it will oxidize the movement of your watch and cause damage to the internal accessories of the movement.

If necessary, you can take a free test at our store.

If the water ingress is not very serious, but there is fog on the watch glass, you can directly wear the watch on the wrist directly, and the best solution is to go to the after-sales center in time, and the maintenance technician will remove all the parts and wipe the oil one by one to ensure that the watch has no possibility of rust. It should be noted here that it is timely, delaying the repair will often delay the best time for Carl F. Bucherer watch maintenance, resulting in damage to the parts.

Hello, glad to answer for you!

1. If the water ingress is not serious, but there is a layer of fog on the surface, you can use toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly.

If the watch is faulty, you can click below to consult the official** or click on the avatar to call for consultation**!

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage. You can click on my homepage ** to consult, I hope to help you.

Water ingress in a Glashütte watch can cause damage to the watch movement, and if left untreated, it can corrode the watch movement, causing the watch to run inaccurately or even not to go. The stagnant water in the watch case should be removed in time, and then the watch should be sent to a professional watch repair center for oil washing and maintenance. Prevent serious damage to the watch caused by excessive time.

The watch is a sealed environment, and it is difficult for water vapor to volatilize on the dial, and if it is placed too long, it will cause the parts inside the watch to rust. The cost of different models of the same watch is also different, it is recommended to call ** for detailed consultation.

What should I do if my watch gets water?

1. If the watch is soaked in water, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the water vapor in the watch can be eliminated.

2. Put it in a rice jar and bury it deep in the dried rice for a period of time, if it is fast, you can see obvious results in one night.

3. You can use a granular substance called silica gel to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will disappear.

4. Take a hair dryer to dry, and then apply a layer of transparent nail polish on it to avoid impurities and prevent rust.

5. If there is water vapor in the watch, you can wear the watch face inward and the bottom shell outward, and wear it on the wrist to eliminate the water vapor in two hours. If there is too much water in the watch, the case must be opened and scrubbed. If you are not sure to deal with it yourself, you should send it for repair in time.

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Method 1: If the watch is soaked in water, you can use several layers of sanitary paper or flannel cloth that is easy to absorb moisture to tightly wrap the watch, put it at about 15 cm near a 40-watt light bulb, bake for about 30 minutes, and the water in the watch can be eliminated. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method 2: Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the moisture can be eliminated after a few hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method 3: Put granular calcium chloride into a closed container with the watch that has been flooded, and after a few hours, take out the watch and the stagnant water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

If the watch gets into the water, it should be dealt with in time, and it needs to be scrubbed and maintained by the watch maintenance institution. If the watch is not repaired in time, then the water will rust the steel parts in the watch movement, and the tiny clock parts usually need to be replaced once they are rusty, in addition to the movement parts, long-term contact with water vapor will also make the watch dial, blistering and rust occur.

Some people think that their watch is a waterproof watch, and they often fall into some misunderstandings. For example, wearing a watch to take a hot bath or go to a sauna is completely wrong. Because the watch itself is not an absolutely sealed shell, that is to say, waterproof is not necessarily waterproof vapor, no matter how many meters it is indicated, it cannot be used in hot water greater than 40C°.

If the water ingress into the watch is more serious, remember not to dispose of it by yourself to avoid unnecessary losses. It is recommended to take the watch that has been damaged by water to a professional repair shop for oil polishing to remove moisture from the movement and prevent the watch parts from rusting.

Even if the watch is water-resistant, not all water is protected against water. For example, the 30-meter water resistance can only prevent hand sanitizer, face wash, rain, car splashing, etc. If you take a bath, swim, etc.

The watch can't stand it anymore. Consumers are reminded that no matter how deep the water is waterproof, they should not wear a watch sauna. The heat of the steam accelerates the deterioration of the waterproof rubber ring and does not protect the movement properly.

If there is water in the watch because the quality of the watch is still not up to par, and the closure is not strict, you must negotiate with the seller.

Glashütte Watch Aftermarket**: 400-659-0877

Generally speaking, if there are water stains on our Glashütte watch, and after a period of time there is a shutdown on the watch, then you can judge whether there are water stains on the watch, and if there are water stains on the watch, the error on the watch is large, and you can also judge whether there are water stains on the watch. In addition, when we look at the hands in the Glashütte watch, the hour hand in the watch does not look very clear, and we can also tell that the hour hand in the Glashütte watch has been flooded.

The reason why the watch gets water is because you didn't take off the watch when you took a shower or washed your hair, which caused water vapor to get in.

There are generally three ways to enter the water in the watch, the watch is worn backwards, the desiccant is removed and the lamp is baked to remove the water, it may seem that the effect is not bad, but the fact is not satisfactory, those methods can only remove the water stains on the surface, and the water stains that penetrate into the movement can not be removed with certainty, and it is not too much to treat those small watches, but for those famous watches, if this method is adopted, I am afraid that it will be regretted in the future. If this method can be handled completely, then the repairer will not have to eat. It is recommended to send it to a professional repair point if it enters the water.

Hello, the watch water generally has water mist or water droplets on the watch glass, and it will corrode the movement for a long time, resulting in inaccurate or non-time, so the earlier the watch water treatment time, the less damage to the movement, the recommended treatment methods are as follows:

Law. 1. Place the vent - dry the watch with a dry paper towel and then place it in a cool and dry vent for a few hours, and do not place the watch directly in the sun or dry, which is to prevent water mist from flowing into the movement.

Law. 2. Silicone drying - for the water inlet of the mechanical watch, you can use the granular substance of silica gel to absorb water, put the two in a closed container, and take it out after a few hours, and the water mist inside will be cleaned up; If it is a quartz point clock, you can take a few small pieces of calcium chloride, wrap them in gauze, and then open the electronic watch cover and seal it.

Law. 3. Wipe oil and remove rust - method 1 and method 2 can only clear a slight water mist, and for some more serious water ingress, these two work earlier, which is not enough for the rescue time of the movement, at this time it is best to find a professional watch repair center for ** maintenance, oil wiping treatment.

Glashütte Watch Care Center: 400-659-0877

Quartz watches allow a margin of error of 15 seconds per month. Quartz watches are powered by battery energy, and the typical battery life varies from 12 to 24 months, depending on the movement used in the watch. If your watch has a weak current display, the second hand will only jump every four seconds when the battery is almost exhausted, if this happens, you should replace the battery immediately.

If you find that the time is slow, it may be caused by insufficient power, you can go to the authorized maintenance center to check the power of the two-pin quartz meter to adjust one minute faster to compensate for the gap between the magnetic wheels.

The Shanghai Glashütte watch is in Room 918, 9th Floor, Landmark Plaza, Nanjing East Road Pedestrian Street, Huangpu District, Shanghai, and the watch must be kept dry at all times. If you accidentally get wet, wipe the water off your watch carefully and thoroughly with a dry, soft, absorbent cotton cloth to avoid rust.

Hello, the inside of the watch is flooded, I suggest that you go directly to the relevant after-sales service center to deal with it, and professional things should be done by professional people. You can also click on my homepage to consult and understand the after-sales service, and deal with the degree of water ingress in your watch to ensure that the watch is in good condition. It can also avoid unnecessary troubles caused by unfamiliar table structure when you operate independently.

Prepare a little paper towel or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. Later, you will notice that the moisture in the movement gradually disappears. Welcome to consult.

If the watch is flooded, it should be sent to the service center for repair in time, so as not to corrode the inside of the movement and increase the maintenance cost over time.

The address of Chengdu is in Room 05, 24th Floor, Sichuan Aviation Plaza.