Why do my family s electric hair clippers keep cutting hair? 5

It should be that there is too much broken hair accumulated between the blades, which hinders the operation of the electric hair clipper, so the electric hair clipper keeps cutting the hair.

Solution: 1. Prepare tools, brushes and picks.

2. Observe the layout of the push head of the electric pusher, which is generally like this.

3. Place the pry blade in the middle of the front of the electric pusher head and the gap between the metal, look at the icon, the direction of the pry is the side marked in the previous step, don't work too hard, a little hard, you can pry up.

4. Remove the electric pusher, you can see that there is a lot of hair inside, clean it up with a brush.

5. The most important place is to press the lower part of the white part according to the diagram, separate the two metal pieces of the electric pusher, and clean the hair in the middle with a brush.

6. Install it back.

1. The contact distance of the scissor blade is loose, like the screw in the middle of the scissors is loose, and you can't cut anything, so you can disassemble and tighten it;

2. The blade has been aged for a long time or lacks oil, and it is not sharp, either change the knife head and try some oil first.

It shows that everyone uses hair source hair products, and the hair grows like a steel wire. It's not that the faders are bad!

I bought it online newly, and I just bought it back and kept cutting my hair.

Didn't you try it when you bought it?

It should be that there is too much broken hair accumulated between the blades, which hinders the operation of the electric hair clipper, so the electric hair clipper keeps cutting the hair. Solution: 1. Prepare tools, brushes and picks.

2. Observe the layout of the pusher head of the electric pusher, which is generally like this cover. 3. Place the pry blade in the middle of the front of the electric push head and the gap between the metal, look at the icon, the direction of the pry is the side marked in the previous step, don't work too hard, a little hard, you can make trouble to pry up.

The coil is heated and burns out.

1) If the use time is too long, beyond the allowable range, the new coil should be replaced, and the use conditions should be improved.

2) The armature is crushed to death under long-term power. The head should be cleaned or the armature position should be adjusted.

3) The internal turn short circuit due to aging of coil insulation or coil vibration. The coil should be replaced with a new one and securely fastened.

Summary. It may be that the blade is misaligned, adjust the position of the blade, you can use a screwdriver to loosen the two screws on the blade to adjust, remember to lock it tightly and fix it with the blade.

It may be that the blade is misaligned, adjust the position of the blade, you can use a screwdriver to loosen the two screws on the blade to adjust, remember to lock it tightly and fix it with the blade.

I can't find a place to adjust, I can't find a place to adjust, I can't find a place to adjust, I can't find a place to adjust.

I couldn't find a place to adjust.

Can't find a place to adjust.

There is also a possibility that the blade is blunt, and the blade needs to be replaced, and the electric clipper is generally composed of fixed pushing teeth, movable pushing teeth, adjusting the handle, the shell and the electrical parts installed in the shell. It is a haircut, a hairdressing tool. There are generally two types of electric hair clippers, one is plug-in and the other is rechargeable.

Lack of power, charge.

1) Beautiful appearance, light weight, flexible operation, labor-saving, low vibration and low noise.

2) The blade has good hardness, the scissor edge is sharp, and the cutting is light and free, without pulling and pinching.

3) The upper blade movement range is not less than. The contact surface of the lower blade should be flat and smooth. Blades should be available in a variety of specifications such as coarse, medium and fine.

4) The electric thrust shear insulation must be good and reliable, and there should be no leakage. At the same time, use continuous 8min for full load, 4min for closing, and then 8min for continuous use. The temperature rise of the lower blade should not be higher than 15, and the temperature of the solenoid coil should not be higher than 65.

2. AC electromagnetic type 1, the blade load is too large and is crushed; 2. The coil is broken; 3. If the blade is rusty, if you want to repair it yourself, you must first determine that the power is normal, and then disassemble the blade and clean it with kerosene or alcohol and then install it.

The hair clipper is yellow when it is charged, and the key is to push it up, and the yellow light is not on and does not run, what is going on.

The unfast hair clipper can be caused by a number of reasons, such as the blades have worn out, the inside of the machine needs to be cleaned and maintained, etc. If the electric hairclipper is not fast, we can try the following methods to solve this problem.

First of all, we can check if the blade needs to be replaced, if it is already worn, it will lead to an unhappy situation of the fader. At this time, we need to replace a new blade, usually the original factory of the electric hair clipper will give the blade replacement calendar and instructions, you can replace it according to the instructions.

Secondly, we can also consider a comprehensive cleaning and maintenance, because during use, hair and dust are easy to adhere to the inside of the machine, affecting the operation effect. Cleaning can be done with a special detergent or with clean water, and the blades and the inner case of the machine can be gently cleaned with a soft-bristled brush. Of course, when using detergent or water, you need to pay attention to cutting off the source of electric imitation seepage to avoid electric shock accidents.

Finally, if neither of the above methods can solve the problem, we need to consider enlisting professional help. Professional maintenance personnel can carry out a more comprehensive inspection and maintenance of the electric hair clippers to solve the problem as soon as possible. At the same time, repairing all kinds of big and small problems can also avoid problems such as excessive noise after using it for a long time.

In short, it is not a big problem for the electric hair clipper to be unhappy, and we can try to solve it with a new blade or do cleaning and maintenance. If you really can't solve the problem, you can consider contacting a professional maintenance personnel. In this way, we can keep our hair neat and tidy without being bothered by the slow and unpleasant electric hair clippers.