Do you want to match after cleaning the throttle?

Cleaning the throttle must be matched by the computer, because the cleaning of the throttle must be due to the blockage of the trachea, at this time, the computer is based on the blockage of the trachea for some related matching, the throttle is cleaned, and the relevant computer matching must be carried out. Otherwise, it doesn't match.

Throttle valve is a controllable valve used to control air entering the engine, and after entering the intake pipe, it is mixed with gasoline (different styles of cars, different design mixing parts) to become a flammable mixture of gas, which participates in combustion work. Four-stroke gasoline engines are roughly like this. The throttle valve is one of the most important components of the engine system of today's EFI truck, its upper part is the air filter [air grid], and the lower part is the engine block, which is the throat of the automobile engine.

Whether the car accelerates flexibly or not has a lot to do with the dirt of the throttle, which can reduce fuel consumption and make the engine flexible and powerful. Whether the throttle should be removed and cleaned is also the focus of much discussion among car owners.

The computer has a memory function, has adapted to the state before the throttle cleaning, after the cleaning of the throttle opening changes (even if it is very small) directly reflected to the computer, there are two kinds of signals, the common phenomenon is idle high and low or high idle, so it is recommended to use the detection computer to match.

Do I need to match after throttle cleaning? Don't be stupid and be cheated again, the old driver will teach you what to do.

The carbon deposition of the car is difficult to avoid, and the harm to the car after the carbon deposition is also very large, the carbon deposition is all over the throttle, air intake, injector, piston rod top, to clean up the carbon deposition in an all-round way only wash these areas. Carbon deposition on the throttle is the most obvious, just open the intake hose, the human eye can see the level of dirty throttle, and the intake hose is also very easy to open, with only one buckle. Therefore, drivers with a little self-learning ability can clean it by themselves, and there are many people who wash it by themselves, and the price of throttle cleaner is also very cheap.

Cleaning the throttle is not just a matter of spraying and wiping, and there is also the last key process after washing, the pairing of the throttle.

Do I need to match all the cars after they are washed? Not all cars need to do it, but all the cable throttle does not need to be matched, and all electronic devices must be matched. Since the cable-type throttle valve is closed when idling, only the air intake of the idle motor is used, so there is no harm to the idle speed after washing.

The electronic device throttle does not have an idle motor, and the throttle does not close completely when idling, and will continue to have a small opening. How can you tell if your car is cable-based or electronic? Just look at the throttle valve with a cable or a power plug, the one with a cable is a cable throttle, and the one without a cable and a power plug is electronic.

What are the effects of throttle mismatching? There is only one hazard, the idle speed will be high, and the level of the car is not the same, about 1300 rpm to 2500 rpm. High idle speed not only endangers fuel consumption, but also can not drive normally and safely, especially in the case of development and slow driving, the speed can not be well controlled.

How this happens is due to the fact that the throttle has an automatic memory adjustment effect. There was originally carbon deposit, the safety channel of the air intake was reduced, and the throttle valve would open a little more on its own to ensure that there was sufficient air intake at idle. If the carbon deposit is removed, the throttle opening will not be easy to shrink immediately, and the opening will continue to be maintained when there is carbon deposit.

At this time, the carbon deposit has long been gone, the safety channel has become larger, the air intake has expanded, and the idle speed has become higher.

If it can't be matched, the hanging wire throttle can be cleaned casually, and the electronic device throttle is best not cleaned by itself. Even if you clean yourself and go to the car 4S shop only to match, you have to pay a lot of labor costs, and the calculation is not as good as immediately letting the car 4S shop wash it. Even if the throttle has a self-learning effect, in fact, if it is not matched, it can be recovered after a few days of driving.

However, it is necessary to look at how high the speed is, if it is only 1300 rpm or even lower, it is not very harmful to be able to drive continuously for a few days. If it is more than 2000 rpm, there is no way to open, the instant vibration of the gear will be very large, not to mention the development of driving, everything is normal driving does not give the throttle speed ratio of 2000 rpm, to always use the brake to control the speed, both consume gasoline and diesel, and consume car brake pads, and the safety performance can not be ensured. Therefore, the high-pressure root cannot be opened at the waiting speed, and the only way to do it is to match.

The idle speed is unstable or about 30,000 kilometers to clean. There are 2 ways to clean the throttle: one is no-wash.

Because the computer has a memory function, it has adapted to the state before the throttle is cleaned, and the opening of the throttle after cleaning changes (even if it is very small).

Yes. If this thing is particularly dirty, you need to make some adaptations after cleaning, so as to ensure the normal use of the car.

Yes, the cleaning throttle valve must be matched, otherwise it cannot be installed back, and these parts have strict dimensions.

You have to match accordingly, so that you can choose one that matches your car.

After cleaning the throttle body, it is best to use the diagnostic computer to do the initial setting, many models can also manually match the throttle body, the idle speed will be stable after matching, and the fuel consumption will be the most economical, if there is no difference between the idle speed and before cleaning, it means that the engine is working normally without any problems.

Be bold to dismantle, you can clean it yourself, it's very simple, the first step must be to remove the battery anode, wait a few minutes and then dismantle the throttle to clean, don't use the computer to match, after the car is driven down to speed down and drive out for a few laps on it, tens of thousands of cars are not so arrogant.

Do I need to match after throttle cleaning? Don't be stupid and be cheated again, the old driver will teach you what to do.

The car throttle does not need to be matched after cleaning, of course, you can do it if you want. Because most of today's cars are electronic throttle, the driving computer will inject fuel according to the intake volume of the throttle, and the driving computer is also relatively smart, with a self-learning function, when he finds that after the intake valve is cleaned, the air intake volume is on when idling, and it will inject less fuel according to the situation, so it is not needed.

After the car throttle is cleaned, it needs to be matched, because the mismatch will make it difficult for the car to control the accelerator during driving, and it will consume fuel.

Normally, it is necessary to match, but now the electronic system of many cars will automatically match, so there is less manual operation.

It must be cleaned, the car throttle valve produces blockage and garbage in the polluted air, and the car will be smoother only if the throttle is cleaned.

Do I need to match after throttle cleaning? Don't be stupid and be cheated again, the old driver will teach you what to do.

It is better to match the throttle after cleaning, otherwise the fuel consumption of the car will increase in a short time. It's okay that the mismatch is good, and the fuel consumption of the car will return to normal after driving for a while. Riders better match it, though.

Prolonged use of the throttle valve will cause carbon deposits that affect engine operation.

The ECU of the engine has a strong learning ability. When the ECU detects a carbon deposit on the throttle, it will use another set of control logic to control the throttle with the deposit. After the rider cleans the throttle, if it does not match the computer, the ECU still uses the control logic of the throttle to control the throttle without carbon deposits, which will lead to an increase in the fuel consumption of the car.

However, ECU is very capable of learning. After the car has been driven for a while, the ECU detects that there is no carbon deposit on the throttle, so it uses the control logic that has no carbon deposit to control the throttle.

Therefore, after cleaning the throttle, if it does not match the computer, the fuel consumption of the car will increase for a short time, but it will return to normal after driving for a while.

When you usually use the car, you can regularly clean up the carbon deposits on the throttle. It is recommended that cyclists should be equipped with a computer after each wash to avoid the phenomenon of increased fuel consumption of the vehicle.

When removing engine carbon deposits, it is recommended to use the walnut sand removal method, which has a significant effect. Many repair shops are using the bottle hanging method to remove carbon deposits, but the effect of this method is not obvious.

Millions of car purchase subsidies.

Not necessarily, all cable throttles do not need to be matched, electronic throttles need to be matched.

The cable throttle does not need to be matched, and the cable throttle has one more component than the electronic one, that is, the idle motor, and the electronic throttle does not have an idle motor. When the throttle is idle without the accelerator, the cable throttle baffle is completely closed, and the air required for idle is entered by the idle motor. The pull cord throttle does not have the ability to self-regulate, and if you don't step on it, you will turn it off completely, and the computer will always think that it is completely closed when you don't step on the accelerator.

The electronic throttle does not have an idle motor, and when the throttle is idle, the throttle flap also has a small opening to allow the air to enter the idle state, which means that it can never be completely closed. If the throttle is dirty, carbon deposits occupy the passage of the throttle, and the air entering the channel will not be smooth, resulting in insufficient air intake, unstable idling, or even inability to idle.

The throttle has a self-adjusting function, and if carbon deposits are detected blocking part of the channel, then open the throttle baffle a little more when idling, that is, let the throttle open a little more, and the channel will be enlarged, so that there will be enough air to enter. The ability to self-regulate is limited, it is impossible to adjust it infinitely, when it is adjusted to the maximum, there will be an unstable phenomenon of idling, and many cars will also light up the fault lights to tell the driver that the vehicle needs to be overhauled.